PDF download Download Article PDF download Download Article

Adjusting the action on a bass (which is the height of the strings from the fret board) is an important part of the overall setup of the instrument. This must be done when the instrument is new. In addition, exposure to temperature changes, humidity changes and changes in string gauge can affect the setup of your bass and necessitate adjustment of the action.

Part 2
Part 2 of 4:

Inspect the Neck of the Bass

PDF download Download Article
    • It takes time for the neck of a bass to settle into its final position after significant changes have been made to the forces applied to it.
    • Waiting longer periods will increase the accuracy of your adjustments.
  1. [2]
    • The neck of your bass must have a slight bow to play properly. If the neck were straight, you would get fret buzz, especially on notes played on the first 5 frets.
    • If you have a capo, attach it at the first fret; otherwise, hold down the E-string (or B-string on a 5-string bass) at the 1st fret with your left index finger. Hold the string down at the 12th fret with your right thumb or right elbow. Use a feeler gauge to determine the largest gap between the string and the tops of the 4th through 8th frets. If the string is touching any of these frets, the neck needs more relief. If the gap between the string and any of these frets is greater than 0.020 inch (0.5 mm), then the neck needs less relief.
    • Alternatively, attach a capo at the first fret or hold down the G-string at the 1st fret with your left index finger. Press the G-string down at the end of the neck with your elbow. Use a feeler gauge to measure the gap between the bottom of the string and the top of the 8th fret. If the gap exceeds 0.012 inch (0.3 mm), the neck needs less relief. If there is no gap, the neck needs more relief.
    • The truss rod needs to be adjusted if inspection of the neck indicates that it needs either more or less relief.
  2. Advertisement
Part 3
Part 3 of 4:

Adjust the Truss Rod

PDF download Download Article
    • Depending on the model of your bass, you will need a small Phillips screwdriver to remove the screws securing the truss rod cover or a small flat-blade screwdriver to "pop" or pry off the truss rod cover.
  1. [3]
    • If the neck needs less relief, you will tighten the truss rod by turning the truss rod nut clockwise.
    • If the neck needs more relief, you will turn the truss rod nut counterclockwise.
  2. After a 1/8-turn, tune the strings again and remeasure the string height.
    • If there is fret buzz when playing at any of the first 5 frets, the neck is too straight and the truss rod needs to be loosened.
    • If there is fret buzz only above the 12th fret, there is too much relief in the neck and the truss rod needs to be tightened.
    • If there is fret buzz consistently up the neck, the truss rod is likely set properly and the bridge needs to be raised to adjust the action.
  3. Advertisement
Part 4
Part 4 of 4:

Adjust the Action

PDF download Download Article
  1. [4]
    • If your bass does not have individual saddle height adjusting screws, you must adjust the action by raising or lowering the entire bridge. There are many bridge designs, each with its own specific adjustment features. Select the proper tool for the adjustment hardware on your bass. Typically, tightening (turning clockwise) bridge height adjusters will raise the action and loosening (turning counterclockwise) bridge adjustment adjusters will lower the action.
    • If your bass has individual saddle height adjusting screws, make general action adjustments by raising or lowering the entire bridge, then make your final adjustments by changing the height of the individual string saddles. Individual string saddles are generally adjusted with allen wrenches.
  2. You have lowered the action too much if you hear fret buzz.
  3. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    How do you recommend people maintain their guitars?
    Nicolas Adams
    Nicolas Adams
    Professional Guitarist
    Nicolas Adams is a 5th generation musician of Serbian Gypsy descent and the lead guitarist of the band Gypsy Tribe. Based in the San Francisco Bay Area, Nicolas specializes in Rumba Flamenco and Gypsy jazz and playing the guitar, Bouzouki, Balalaika, and piano.
    Nicolas Adams
    Professional Guitarist
    Expert Answer
    Avoid leaving it out. Always keep it in a case or covered with humidity control, especially for guitars without a truss rod. As far as physical appearance, avoid sunlight for long periods of time, which will fade and damage the guitar. Avoid severe heat, severe cold, and severe moisture. Keep it in that perfect temperature range of around 68 degrees to 72 degrees. As far as dust and dirt and oils go, make sure that the guitar is cleaned properly before putting it away. Wipe down all the strings. Make sure there's no oil from your hands or other things on the face, top, or sides of the guitar, which can get into the guitar or damage the varnish. There are whole kits that come with everything such as oil cleaner, wax, and fret polish. It's important to clean in between the frets, where dirt and grime can go because those can wear down the frets faster.
  • Question
    What makes playing the bass difficult?
    Nicolas Adams
    Nicolas Adams
    Professional Guitarist
    Nicolas Adams is a 5th generation musician of Serbian Gypsy descent and the lead guitarist of the band Gypsy Tribe. Based in the San Francisco Bay Area, Nicolas specializes in Rumba Flamenco and Gypsy jazz and playing the guitar, Bouzouki, Balalaika, and piano.
    Nicolas Adams
    Professional Guitarist
    Expert Answer
    One of the harder things is keeping your focus and not losing your place when dealing with different strings. Also, learning different patterns can be difficult such as different walks, runs, and structural patterns on the baselines. It also wears on your hands a lot more than any other guitar because it's heavier. If you don't have a callus, you'll definitely develop one.
  • Question
    What's a good cleaner for the neck of a bass guitar?
    Community Answer
    Community Answer
    There are many different products made for wooden instruments. Go to your local music shop and tell them the type, age, and brand of your instrument and they should be able to advise you.
See more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!

Warnings

  • Do not force the truss rod nut. If it does not turn freely, stop and contact a qualified dealer or repair center. It is possible to break the truss rod by over-tightening it, and end up paying a lot more than you were willing to give.
Advertisement

Things You'll Need

  • Electronic tuner
  • Capo
  • Feeler gauge
  • Small Phillips screwdriver
  • Small flat-blade screwdriver
  • Allen wrenches

About This Article

Nicolas Adams
Co-authored by:
Professional Guitarist
This article was co-authored by Nicolas Adams. Nicolas Adams is a 5th generation musician of Serbian Gypsy descent and the lead guitarist of the band Gypsy Tribe. Based in the San Francisco Bay Area, Nicolas specializes in Rumba Flamenco and Gypsy jazz and playing the guitar, Bouzouki, Balalaika, and piano. This article has been viewed 390,541 times.
180 votes - 86%
Co-authors: 11
Updated: March 28, 2021
Views: 390,541
Categories: Bass Guitar
Article SummaryX

Adjusting the action on your bass is important when you have a new bass or when the instrument’s been exposed to temperature or humidity changes. To start, use an electronic tuner to tune your bass as you normally would. This will ensure the strings are at the proper tension when you adjust the action. Once you’ve tuned it, wait 30 minutes for the strings to settle. Then, inspect the neck of your base to see how much relief it has. A bass neck should normally have a slight bow. Too much bow or too little bow means you need to adjust the truss rod on the bottom of the headstock. Once you’ve done this, raise or lower the bridge or the individual string saddles on the bridge with an Allen wrench. Test your action adjustments by playing your bass at each fret. If you hear buzzing, you’ve lowered the action too much and need to adjust it. To learn how to test your truss rod adjustments with a capo, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 390,541 times.

Reader Success Stories

  • Mark Meszaros

    Mark Meszaros

    Feb 4, 2019

    "Although I already knew how to set up my bass (in fact, any guitar), I liked this guide a lot. Also, this is what I..." more
Share your story

Did this article help you?

Advertisement