This article was co-authored by Jonas Jackel and by wikiHow staff writer, Kyle Hall. Jonas Jackel is the Owner of Huckleberry Bicycles, a bicycle retail store based in San Francisco, California. Jonas has over 20 years of experience managing bicycle retail stores and has operated Huckleberry Bicycles since 2011. Huckleberry Bicycles specializes in servicing, repairing, and custom building road, cross, gravel, touring, folding, and e-bikes. Jonas was also previously sat on the Board of Directors for Bike East Bay, a bicycle-advocacy non-profit organization based in Oakland, California.
wikiHow marks an article as reader-approved once it receives enough positive feedback. This article received 18 testimonials and 88% of readers who voted found it helpful, earning it our reader-approved status.
This article has been viewed 1,106,030 times.
Routinely adjusting your bike brakes will help them perform better and ensure you’re riding safely. The two main things you’ll want to adjust in your bike’s brake system are the brake pads and the brake cables. Worn down brake pads that are too low or high on the rim can be a safety hazard. Brake cables that are too loose will make it harder to brake. Fortunately, you can easily fix these issues with some simple tools!
Bike Brake Adjustment Guide
Loosen the bolts on the brake pad with an Allen wrench. Then, move the pad up or down until it is centered and re-tighten the bolts. To tighten the brake cables, turn the barrel adjusters counterclockwise. Or, loosen the bolt on the brake cable and pull the cable outward.
Steps
-
Check your brake pads before you make any adjustments. The brake pads are the pads that clamp down on the front tire of your bike when you pull the brake lever. If the brake pads are worn down past the line labeled “wear line,” you’ll need to replace them before you make adjustments to your brakes.[1]
- If the wear lines on your brake pads aren't labeled, they should be marked by grooves on the side of the pads instead.
- You can order new brake pads online or pick some up at your local bike shop.
- Make sure your wheel lines up correctly in the dropouts as well, or else it won't make good contact with your brakes.[2]
-
Squeeze the brake lever to see where the pads hit the rim. Both brake pads should be coming into contact with the rim of the front tire at the same time. They should be hitting the center of the rim, with an equal amount of space above and below the pad. If the pads are hitting the rim too high or low, they could come into contact with the rubber part of the tire or the spokes on the bike.[3]
- Crouch down to get a good look at the brake pads as you're squeezing the brake lever.
- If your bike has a quick-release mechanism, check that it isn't loose or hasn't come undone. Otherwise, your brakes won't squeeze tightly on the wheel.[4]
Advertisement -
Use an Allen wrench to loosen the bolts holding the brake pads in place. Turn the Allen wrench counterclockwise to loosen the bolts. Don’t loosen the bolts all the way or the brake pads will come out of the brake pad holder.[5]
-
Move the brake pads up or down in the brake pad holder. They should easily move up and down once the bolts are loosened. If the pads were too low on the rim, move them up until they’re centered. If the pads were too high on the rim, move them down until they’re centered.[6]
-
Re-tighten the brake pad bolts with the Allen wrench. Keep turning the Allen wrench clockwise until the bolts are fully tightened. Check to make sure the brake pads are centered. Readjust if needed.[7]
-
Test the tightness of your cables by pulling each brake lever. When you pull the brake levers, they should be about 1 ½ inches (3.8 cm) away from the grip on the handlebars. If the levers hit the handlebars when you pull them, the brake cables are too loose.[8]
-
Loosen the barrel adjusters for minor brake cable adjustments. If your brake cables are just slightly loose, loosening the barrel adjusters might fix the problem. The barrel adjusters are located where the brake cables meet the brake levers.[9]
- Loosen the barrel adjuster attached to the loose brake cable by turning it counterclockwise. Loosening the barrel adjuster will actually slightly tighten the brake cable.
- After you loosen the barrel adjuster, pull the brake lever to see if it fixed the problem. If the brake cable is still too loose, you’ll need to adjust it on the caliper. Leave the barrel adjuster as it is. Don’t tighten it yet.
-
Unscrew the bolt holding the brake cable on the caliper. The caliper is the main frame of the brakes that the brake pads are attached to. The brake cable is the thin cable extending off the caliper. Locate the bolt that’s holding the brake cable. Use an Allen wrench to turn it counterclockwise a few times until the bolt is slightly loose.[10]
- Don’t unscrew the bolt all the way. Just rotate the Allen wrench counterclockwise 2-3 times until the bolt is loose.
-
Pull the brake cable outward to tighten it. Now that the bolt is loosened, you shouldn’t have any problem pulling the cable. Hold it in place with your fingers once you’ve pulled it taut. As you pull the cable, the brake pads should tighten on the rim of the front tire. You want them to be tight enough that there’s some resistance when you turn the tire, but not so tight that the tire isn’t able to turn at all.[11]
- If you can't turn the tire at all, pull less hard on the brake cable so it's not as tight.
-
Tighten the bolt holding the brake cable on the caliper. Use the Allen wrench and turn it clockwise 2-3 times until it won’t turn anymore. The cable should be secure in place once the bolt is tightened.
-
Tighten the barrel adjusters on the handlebars. Turn the barrel adjusters you loosened before clockwise several times until they’re fully tightened. Tightening the barrel adjusters will loosen the brake pads that are clamped onto the front tire. Once the barrel adjusters are tightened, your brake cables should be all set!
- Test the brake cables again by pulling the brake levers. When you pull the levers now, there should be 1 ½ inches (3.8 cm) between the lever and the grip on the handlebars.
Community Q&A
-
QuestionHow do I adjust the back brakes? The pads do not close onto the rim at the same time.Paul SCommunity AnswerThe calipers have an internal recoil spring on each side. The small screw on the side near the pivot mount increases or relieves the tension. A clock-wise turn pulls that side away from the rim, while a counter-clockwise turn on the opposite side will help pull the closer pad away from the rim. Adjust each at the same time in half-turn increments, testing the brake pull after each adjustment. Usually the pads can be centered evenly after 2.5 to 3 turns. Neither side should be full-turned to its maximum in or out. Lubricate the pivot mount with a little WD-40 and insure the brake cable is not binding.
-
QuestionOne brake caliper touches the wheel, and when I tighten the caliper, the tire never moves away. When I loosen it, no break bits touch the tire. What do I do?Paul SCommunity AnswerThere is a recoil spring tension adjustment on the calipers near the mounting pivots on each side. Turning it clockwise increases the tension on the internal spring, allowing it to pull farther away from the rim. The side that is moving too far would need counter-clockwise turns to relieve tension, and the side not pulling away enough, clockwise turns. Turn these screws in half-turn increments, testing after each adjustment. Each side works together and should be adjusted at the same time.
-
QuestionAfter squeezing the brake cables, the brake pads do not retract fully and rest on the tire. They are rubbing the tire and slowing motion, how would I adjust to solve this problem?Bireswar settCommunity AnswerFirst check that the brake pads are in good condition. If they are not, then replace them. If it's still not working, then check the lever that around the wheel that is holding both the brake pads in position and adjust the lever by loosening the central screw on it. Make sure that both the brake pads are in equal distance from the rim of wheel and then tighten the screw again.
Tips
-
If you have mechanical disc brakes, position the bike rotor on the stationary disc rather than the one that moves.[12]Thanks
Video
Things You’ll Need
Adjusting Your Brake Pads
- Brake pads
- Allen wrench
Tightening Your Brake Cables
- Allen wrench
References
- ↑ https://www.mensjournal.com/gear/repair-maintenance-how-to-adjust-your-road-bike-brakes-w434268
- ↑ Jonas Jackel. Bicycle Shop Owner. Expert Interview. 18 February 2020.
- ↑ http://www.cyclingweekly.com/videos/bike-fit-and-maintenance/how-to-set-up-your-brakes-video
- ↑ Jonas Jackel. Bicycle Shop Owner. Expert Interview. 18 February 2020.
- ↑ https://www.youtube.com/watch?v=Qba8JOggjbA&feature=youtu.be&t=167
- ↑ https://www.youtube.com/watch?v=Qba8JOggjbA&feature=youtu.be&t=167
- ↑ https://www.youtube.com/watch?v=Qba8JOggjbA&feature=youtu.be&t=167
- ↑ https://www.youtube.com/watch?v=hg6s596PPRY&feature=youtu.be&t=36
- ↑ http://www.cyclingweekly.com/videos/bike-fit-and-maintenance/how-to-set-up-your-brakes-video
- ↑ http://www.cyclingweekly.com/videos/bike-fit-and-maintenance/how-to-set-up-your-brakes-video
- ↑ https://www.youtube.com/watch?v=hg6s596PPRY&feature=youtu.be&t=92
- ↑ Jonas Jackel. Bicycle Shop Owner. Expert Interview. 18 February 2020.
About This Article
To adjust the brakes on your bike, start by checking your brake pads, which are the pads that clamp down on the front tire of your bike when you pull the brake lever. Pull on the brake lever and see where the pads hit the rim. They should hit the center of the rim with an equal amount of space above and below them. If they're hitting too high or low on the rim, you'll want to adjust them. Just loosen the bolts holding the brake pads in place with an Allen wrench, and move the pads up or down so they're centered on the rim. Then, retighten the brake pads with your wrench. You might also need to adjust your brake cables if your brake levers hit the grip on the handlebars when you pull on them, which is a sign that the cables are too loose. If your cables are just slightly loose, loosen the barrel adjuster attached to each cable by turning it counterclockwise. This will tighten the cables. If one of the cables is still too loose, unscrew the bolt that's holding the cable to the caliper. Then, pull the brake cable out away from the bike and hold it taut to tighten it. You want the cable to be tight enough that there's some resistance when you turn the tire, but not so tight that you aren't able to turn the tire at all. Once you've found the right position, tighten the bolt that's holding the cable on the caliper. Finally, tighten the barrel adjusters you loosened before. For tips on how to tighten or loosen the brake cables on your bike, read on!
Reader Success Stories
-
"Very clear instructions. I love the GIFs to visualize before performing the fix. I had to tighten my handbrake for the rear wheel and had given up entirely on my front wheel (unlatched the caliper). I ended up fixing both because of this article. Thanks."..." more