PDF download Download Article
Step-by-step instructions to construct a concrete foundation for a variety of projects
PDF download Download Article

A concrete foundation is a base for a structure.[1] The type and size of concrete foundation you will need is based on the structure you will place upon it. You may need a concrete foundation for a fountain, or your patio furniture, or even for an air conditioner unit.

  1. The type of foundation depends on the area of the foundation will be located on and the type of structure that will be placed on it.[2]
    • Shallow foundations are built on level ground and hard surfaces.[3] Shallow foundations are no more than 3 feet (0.91 m) (91.44 cm) deep and are used primarily for smaller, simpler projects like holding patio furniture, a fountain, or an air conditioning unit.
    • Deep foundations are used for more complex projects.[4] Deep foundations are also used when soil conditions are poor or when building a structure on a hill. Deep foundations are more than 3 feet (0.91 m) (91.44 cm) deep and can have varying depths throughout. This type of foundation is suited for a shed or a detached garage.
  2. Add 2 feet (0.61 m) (60.96 cm) on either side.[5] This properly spaces the form work and allows you the space you need to lay your foundation.
    Advertisement
  3. Situate and lay down the boards in the planned foundation shape and size.
  4. Adjustments to the form can not be made after the concrete is poured. Because concrete is very heavy, be extra sure your formwork is strong and firmly in place.
  5. [6]
    • Dump the dry cement into the wheelbarrow.
    • Add the water very slowly. Stir constantly.
    • Stir the mixture thoroughly. Mix in just enough water so your cement is chunky. Don't let the mixture get too soupy.
    • Remember to wear safety glasses, gloves, and a mask when mixing concrete.[7]
  6. [8]
    • Pour your ready concrete into your form.
    • Use your trowel to level it off and smooth it over.
    • Make grooves with your trowel if you want a non-slippery surface.[9]
  7. [10]
    • Let the concrete dry.
    • Remove the forms after the concrete thoroughly dries. This will take at least 24 hours.
    • Keep the concrete wet to avoid cracking if it's hot outside.[11] Soak it with a hose at least twice daily, three times if it is very hot outside.[12]
    • Cover the pad if it looks like rain. Rain can cause depressions in the concrete and cause your foundation to be uneven.
  8. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    How deep does a concrete foundation need to be?
    Gerber Ortiz-Vega
    Gerber Ortiz-Vega
    Masonry Specialist & Founder, GO Masonry LLC
    Gerber Ortiz-Vega is a Masonry Specialist and the Founder of GO Masonry LLC, a masonry company based in Northern Virginia. Gerber specializes in providing brick and stone laying services, concrete installations, and masonry repairs. Gerber has over four years of experience running GO Masonry and over ten years of general masonry work experience. He earned a BA in Marketing from the University of Mary Washington in 2017.
    Gerber Ortiz-Vega
    Masonry Specialist & Founder, GO Masonry LLC
    Expert Answer
    It depends on how high you want to make the wall. For instance, if I need a two foot brick wall, I will pour a solid eight inch foundation. The foundation would be eight inches of pure concrete, and I would also put in rebars facing upwards in the concrete, and then I'll place the cinder blocks. After the cinder blocks and the foundation are ready, I can start laying in the bricks.
  • Question
    What is used to make concrete?
    jacob jabben
    jacob jabben
    Community Answer
    The paste, composed of portland cement and water, coats the surface of the fine (small) and coarse (larger) aggregates. Through a chemical reaction called hydration, the paste hardens and gains strength to form the rock-like mass known as concrete.
  • Question
    How do I repair a block foundation?
    jacob jabben
    jacob jabben
    Community Answer
    First find what's wrong with the foundation. For example, if it is a damaged block, you need to remove the block and measure the length of the gap or missing block. Mix up molder and replace the new block, making sure it rests evenly.
See more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Reader Videos

Tips

Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Things You'll Need

  • Boards
  • Shovel
  • Wheelbarrow
  • Cement
  • Water
  • Aggregate
  • Trowel

About This Article

Gerber Ortiz-Vega
Co-authored by:
Masonry Specialist & Founder, GO Masonry LLC
This article was co-authored by Gerber Ortiz-Vega and by wikiHow staff writer, Sophia Bell. Gerber Ortiz-Vega is a Masonry Specialist and the Founder of GO Masonry LLC, a masonry company based in Northern Virginia. Gerber specializes in providing brick and stone laying services, concrete installations, and masonry repairs. Gerber has over four years of experience running GO Masonry and over ten years of general masonry work experience. He earned a BA in Marketing from the University of Mary Washington in 2017. This article has been viewed 635,374 times.
27 votes - 69%
Co-authors: 24
Updated: November 21, 2024
Views: 635,374
Categories: Home Maintenance
Thanks to all authors for creating a page that has been read 635,374 times.

Reader Success Stories

  • Sheryl Smith

    Sheryl Smith

    May 11, 2016

    "I'm a DIYer and I love to read articles that can help me make my home beautiful."
Share your story

Did this article help you?

Advertisement