PDF download Download Article PDF download Download Article

With a little ingenuity, a ride-on mower can be transformed into a garden snow plough. This article will explain how to do this by adapting your existing garden tractor using reclaimed materials, a welding tool and appropriate safety equipment.

Method 1
Method 1 of 3:

Choosing Your Tractor

PDF download Download Article
  1. Your tractor will also need to be able to bear the weight of the plough blade on its frame. Don’t attempt the conversion unless you are sure it can handle it.
    • Rather than risk converting the mower yourself, consider purchasing one that already has a snow plough attachment available from the manufacturer. John Deere tractors offer this as an option.
  2. You’re advised to get your tractor serviced before you begin. Check the frame carefully for rust. Rust will weaken the structure, making it less likely that it will be able to bear the weight of a snow plough blade at the front while also being able to push snow out of the way.
    Advertisement
  3. Remember also that garden tractor tires aren’t usually intended for use on snow. You might like to consider fitting snow chains to the tires in addition to converting the front fitting.[1]
    • Wheel weights may also help rebalance the vehicle.
  4. Not all ride-on tractor mowers will be suitable for turning into a snow plough. Some cheap models won’t be heavy or sturdy enough or have enough horsepower to push deep snow out of the way.
  5. Advertisement
Method 2
Method 2 of 3:

Making the Shovel or Plow Blade

PDF download Download Article
  1. You’ll need to find something to form the shovel or blade of your snowplow. Items you can use to make this include:[2]
    • A half oil drum or piece of flat steel sheet about a quarter inch thick.
  2. If using a steel sheet, cut a piece about twice as wide as your tractor and about one and a half times as tall as the front of the tractor. Using a piece of chalk, mark out five sections of equal height along the vertical length of what will be your plow bucket.
    • You’ll want to fold in the top and bottom quarters of the bucket to create curved edge to scoop the snow.
  3. You can bend this sheet by scoring the metal (cutting a shallow groove in it, not all the way through). This will enable you to bend the steel into shape by hammering it between pieces of wood.
    • Once bent, weld the sheet into place at the bend to make sure it retains its shape.
  4. If you don’t have sheet metal, you could try using an old oil drum cut in half or something like an old hot water tank. Oil drums are likely to be lightweight, which means that they will work better for a lighter frame tractor. They will also cut through the snow well but they are also likely to buckle under pressure.[3]
    • Remember that there will be sharp edges where you cut so make sure to store it where someone, like a child, will not be able to reach it.
  5. Advertisement
Method 3
Method 3 of 3:

Putting the Snowplow Together

PDF download Download Article
  1. On most models of tractor you’ll need to make a bracket on the frame and bring that forward slightly in order to position the plowing blade at the front.[4]
    • You can use reclaimed steel joists, or something like metal trusses, as these are adaptable and usually strong enough for the purpose. A welding tool is likely to be useful in attaching the bracket to the vehicle’s frame.
    • Try to remove the motor deck and cutting tool before doing this, both for safety reasons and ease of access.
  2. You now need to attach the plough bucket or blade to the frame using a welding tool. Try to incorporate a pin or lever to allow the plough bucket to manoeuvre side to side. Add a hand-operated lever to the bucket so it can be pushed to manoeuvre it while you are sitting on the tractor.[5]
    • If you are left-handed, consider doing this on the left-hand side.
  3. If you want to incorporate a lift mechanism, you may need to modify the frame slightly to allow for this. You’ll probably need to create a hand or foot lever so the bucket can be lifted by the person riding the mower.
  4. Special garden equipment snow chains are available. Check the tire to see what the wheel size it (it should be written on the tire).
    • Your local garden store may carry these, or you can purchase them online.
  5. Start fitting your snow chains by laying the chain out on the ground by the side of the tractor wheel. Remove any tangles and check for any damage. Drape the chain over the wheel. You’ll then need to move the tractor forward a few inches to wrap the chain around the tire.
    • Finally, clip the chain into place and do up the rest of the fittings so it is securely fastened around the tire and tight enough to grip the snow as required.
  6. For stability, consider adding some weight onto the back end of your tractor to balance out the new weight at the front added by the snowplow blade. To do this:[6]
    • Strap bricks to the back of the tractor. Wheel weights may also help stabilize and balance your tractor.
  7. Advertisement

Community Q&A

Search
Add New Question
  • Question
    What do I do if I don't have chains for the tires?
    Community Answer
    Community Answer
    Drill holes in a strap. Then put bolts into the holes and screw in nuts. That should give you traction.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

  • You also have the option of making a wooden frame to attach the plow with, in which case you’re advised to put a steel edge on as this will help the plow cut through snow.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Warnings

  • Remember also that skin should not be exposed to cold metal when it is below freezing or it can be very painful. You might like to wrap some rags around the level just as a precaution.
Advertisement

About This Article

Charley Helvy
Reviewed by:
Automotive Expert
This article was reviewed by Charley Helvy. Charley Helvy is an Automotive & Diesel Expert based in Avondale, Arizona. He is the founder of Charley’s Garage, an educational YouTube channel focusing on simple videos for automotive and truck enthusiasts. He has over 31 years of experience in the automotive world. He is a Diesel Instructor at the Universal Technical Institute and is a certified ASE Master Heavy Truck Technician. He offers training on gas and diesel engines on his YouTube channel, along with other DIY and explanation videos for beginners and enthusiasts alike. In 2024, he published a complete guide on Emissions Systems in Automotive and Diesel Vehicles. This article has been viewed 100,329 times.
56 votes - 62%
Co-authors: 3
Updated: February 3, 2020
Views: 100,329
Thanks to all authors for creating a page that has been read 100,329 times.

Reader Success Stories

  • Anonymous

    Anonymous

    Aug 12, 2016

    "Steel drum is a great idea, time saver."
Share your story

Did this article help you?

Advertisement