PDF download Download Article PDF download Download Article

Camping can be a lot of fun and a great way to enjoy nature. Many people enjoy using a tent for the ease at which they can be set up. However, tents can be heavy and bulky to carry with you on a camping trip. To make your camping trip less difficult, you may want to use a tarp shelter. Tarps are lightweight and fairly easy to build a shelter with, helping to make your camping trip a comfortable one.

Method 1
Method 1 of 3:

Finding a Good Spot

PDF download Download Article
  1. The best areas for building a tarp shelter are places that have flat ground. This can make creating the shelter a bit easier and will allow you a more comfortable place to sleep in. Take some time to find a nice, flat area before building your tarp shelter.[1]
  2. Once you've found a nice place on the ground for your shelter, you will want to look above it. Dead branches can pose a serious hazard to campers if they are knocked down by wind. Always avoid placing your shelter under any branches that look old, dead, or dangerous to avoid having one fall on you.[2]
    Advertisement
  3. Many tarp shelter designs require you to place a sturdy cord or rope between two trees. This cord will act as the ridge-line for your tarp shelter. It's a good idea to look for a flat spot that has two trees for you to place this cord between.[3]
    • If you can't find two trees, you could try placing two anchor branches in the ground instead.
    • These trees should be roughly as far apart as your tarp is long.
  4. Although it may be sunny and dry when you set your tarp shelter up, the weather may change during your camping trip. It's important to consider what the weather might do in the near future, allowing you to stay comfortable and avoid any damage to your tarp shelter.[4]
    • Figure out which way the winds are blowing. Any “wall” of your tarp shelter should face away from the wind.
    • Avoid putting your shelter in any areas that are low or seem like they could flood during rain storms.
  5. Advertisement
Method 2
Method 2 of 3:

Making an A-Frame Shelter

PDF download Download Article
  1. The ridge-line will support the top section of your tarp shelter. This line is created by stringing a length of cord between two trees. This gives your tarp an elevated point of support and will form the shape of the a-frame tarp shelter. Place the ridge-line using these steps:[5]
    • Tie one section of the rope to a tree. Place it as high up the tree trunk as you would like the roof of your tarp shelter to be.
    • Bring the other end over to the adjacent tree and tie it at the same level.
    • Make sure the cord is as tight as it can be to ensure a strong ridge-line.
  2. Once your ridge-line has been created, you can lay the tarp over top of it. For an a-frame tarp shelter, place the tarp over the ridge-line in the center of the tarp. This will leave equal halves of the tarp hanging down from the ridge-line.[6]
    • Make sure the tarp is equally hanging from both sides of the ridge-line to avoid problems.
  3. After you've placed the tarp over the ridge-line, you can fasten it to the ground. Take one of the bottom sections of tarp and pull it outwards, away from the center of the tent. Once you've gotten it to a place that you like, secure it to the ground by taking these steps:[7]
    • Place a tent stake into the ground, near to the point the tarps corner while it is stretched out.
    • Tie a length of cord between the tent stake and the corner of the tarp.
    • Make sure this cord is tight and holds the tarp securely to the ground.
    • Do the same thing for each of the other three corners of your a-frame tarp shelter.
  4. Advertisement
Method 3
Method 3 of 3:

Making a Lean-to Shelter

PDF download Download Article
  1. The lean-to tarp shelter makes use of a ridge-line. This ridge-line is created by tying a length of rope tightly between two trees or other points of support. This will create a point that you can secure your tarp to and finish your shelter.[8]
    • Find two trees that are as far apart as your tarp is long.
    • Tie one end of the rope around the trunk of a tree. Tie it at the height that you want the top of your shelter to be at.
    • Tie the other end of the rope at the same level on the opposite tree.
    • It's very important that the ridge-line is as tight as it can be.
  2. The lean-to tarp shelter requires you to fix one edge of your tarp to your ridge-line. You can attach the tarp to the ridge-line using cord or rope and many tarps will come with grommets or loops built in. Make sure you attach the tarp to the ridge-line tightly to build a strong tarp shelter.[9]
    • Your tarp may have holes pre-made along its edge. If so, you can thread the ridge-line through these for an easy way to join them together.
    • Many tarps will have loops along the corners or edges that can be used to tie them to your ridge-line.
  3. Once the top edge has been tied to the ridge-line, you can secure the bottom edge of the lean-to tarp shelter. Pull the bottom edge away from the center until it is at an angle that you want. Place anchoring stakes in the ground at the corners of the tarp and tie the tarp to them. This will hold the bottom portion of your shelter securely in place.[10]
    • Most people recommend using a 45 degree angle for their lean-to.
    • Try adjusting the angle to raise or lower the height of the shelter's "ceiling".
  4. Advertisement

Community Q&A

Search
Add New Question
  • Question
    What size tarp would I need to make an enclosed shelter?
    Community Answer
    Community Answer
    It depends how big your shelter is. If you don't know how big your shelter is, then get someone to measure it.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

Show More Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

About This Article

wikiHow Staff
Co-authored by:
wikiHow Staff Writer
This article was co-authored by wikiHow Staff. Our trained team of editors and researchers validate articles for accuracy and comprehensiveness. wikiHow's Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards. This article has been viewed 158,534 times.
73 votes - 81%
Co-authors: 18
Updated: December 20, 2024
Views: 158,534
Categories: Tents
Article SummaryX

Building a tarp shelter when you’re out in the open is a great way to keep you cool and dry. To make an A-frame shelter, look for flat ground with 2 trees as far apart as your tarp’s length. Make sure there are no loose branches in the trees above since they could fall on your shelter. Tie a cord between the trees as high as you want your tarp to be. Make sure the sides of your tarp will face away from the wind. Then, fold your tarp over the cord so both sides are equal in length. Finally, attach a string to each corner of the tarp and stake the strings into the ground. For more tips, including how to make a lean-to shelter with your tarp, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 158,534 times.

Reader Success Stories

  • Anonymous

    Anonymous

    Apr 10, 2018

    "A good reminder of a task I did but needed refreshing so step by step instructions were useful."
Share your story

Did this article help you?

Advertisement