How to Clean and Polish a Conch Shell

Download Article

Preserve your conch for years to come with a little bleach and polish

Reviewed by Claudia & Angelo Zimmermann

Last Updated: January 16, 2024

Download Article

Soaking in Bleach

|

Removing Barnacles

|

Avoiding Mistakes

|

Q&A

|

Things You'll Need

If you picked up some shells at the ocean, it's important to clean them when you get home. A properly cleaned conch shell can be a great souvenir for years to come. To start, soak your shell in bleach for a day. Then, pick off any barnacles and polish the shell with mineral oil.

Things You Should Know

Put on gloves and goggles, then submerge your shells in a diluted bleach solution. Soak them in the solution for 24 hours.^{[1]
X
Research source}
Wedge a screwdriver or pick under any barnacles to pry them off. Then, use a scrub brush to remove stubborn dirt.
Let the shells air dry, then rub them with cotton balls soaked in mineral oil. Allow the shell to dry for 12 hours, then add another coat.

Part 1

Part 1 of 3:

Soaking Your Shells in Bleach

Download Article

When working with bleach, it's vital to wear protective gear for your safety. Put on thick gloves and goggles before mixing your solution. Also, be sure to mix bleach in a well ventilated area such as outdoors or in a garage.^{[2]
X
Research source}
To soak a conch, mix a solution using half bleach and half water. The precise amounts you need of each depends on how many conches you're soaking. You need enough bleach and water to fully submerge your conches.

Advertisement
3
Soak your shells for 24 hours. Once you've mixed the bleach and water, add your conches to the solution. In about 24 hours, you can remove them from the solution. Some of the dirt will have come off, and any stuck on barnacles will be easier to remove.
- Make sure to wear gloves when putting your conches in the solution, as well as when you remove them.

Part 2

Part 2 of 3:

Removing Barnacles

Download Article

1
Pick off any barnacles. A dental tool, flathead screw driver, or strong pick is used to pick off barnacles. Wedge the pick or tool under the barnacle and gently pry it off. This should be fairly easy, as the bleach should have loosened the barnacles.^{[3]
X
Research source}
- If barnacles are being stubborn, chisel them off using a hammer and screwdriver. Angle the screwdriver under the barnacle and gently tap on the end with the hammer. This should dislodge the barnacle.
2
Scrub down your shell. After removing barnacles, take a scrub brush and wipe down your conches. Use light, scrubbing motions to remove any remaining dirt and debris form the shell.^{[4]
X
Research source}
- If some dirt or stains are not coming off, use your thumbnail to gently scratch them out of the shell.
3
Let the shells air dry. It's important that your conch shells air dry. Set them in a dry place where they will not be disturbed, such as a cupboard or cabinet. Do not attempt to polish your shells until they are completely dry to the touch.
- It can sometimes take conch shells awhile to completely dry, especially if you live in a cooler region. It is not unusual for shells to take a couple of days to dry completely.
4
Cover your shell in oil. Once your shells are dry, they may look a little dull from the cleaning process. To brighten them up, dab some mineral oil onto a cotton pad or cotton ball. Rub the cotton on the shell and cover it completely with oil. If the shells is not as shiny as you want after one layer, add another.
- If you do multiple coats, let the shell dry for 12 hours between each coat.

Part 3

Part 3 of 3:

Avoiding Common Mistakes

Download Article

Make sure the shells you take from the beach do not house aquatic life. Tap the shell gently after picking it up to make sure it is empty. If you hear any scuttling, or see an animal in the shell, put it back where you found it.^{[5]
X
Research source}
To dry your shells faster, you can place them out in the sun. However, do not leave them in the sun for more than a few hours. If shells are left in the sun for too long, they will start to lose color.^{[6]
X
Research source}
Be extra cautious when removing barnacles. Only use the chiseling method if it's absolutely necessary. You do not want to crack or damage your shell while removing barnacles.^{[7]
X
Research source}

Community Q&A

Search

Add New Question

Question

Will it harm or fade the pink inside of the shell?

Community Answer

If the shell is artificially colored, it may lose its color. Add a tad bit of mineral oil to brighten up your conch shell if it has dulled during the cleaning process.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 5 Helpful 5
Question

I have a very old, porous, fragile conch shell. I would like to paint it. Would I try to condition it with mineral oil first, or just go ahead and paint it? Should I start with a sealer?

T. Chinsen

Top Answerer

Oil will prevent paint from sticking to the shell, and oil paints will need to used instead. Sealing the shell can do the same if too thick of a coating is applied. If paint and sealant are both water-based, you can combine them and apply it in one step instead of two. Read product label or call their help hotline for an answer. Milk has calcium and can remove ingrained dirt by depositing calcium on the shell under the dirt, causing it to lift off. It may take several days, and the shell needs to be completely covered.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 5 Helpful 4
Question

I have several shells with a broken edge. I want to plant them with succulents. How can I finish the broken edge so it is not sharp?

T. Chinsen

Top Answerer

You can sand down the edges with sandpaper. A sapphire nail file can be an option. Treat the broken edge like a fingernail: file in one direction using the rough side, then the fine side. Like a nail, the shell is formed in layers, and it needs to be treated carefully to avoid breaking more of the shell.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 2 Helpful 4