This article was co-authored by wikiHow Staff. Our trained team of editors and researchers validate articles for accuracy and comprehensiveness. wikiHow's Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards.
This article has been viewed 127,816 times.
Learn more...
It is easy to do regular cleanings on antlers when they get dusty and dirty. Cleaning a new set of antlers that you pick up on the hunt, however, is a bit more labor-intensive. You need to remove all biological material, ensuring that you don’t bring disease into your home. The whole process, however, should only take about an hour.
Steps
-
Saw the antlers off the skull cap. Get a hacksaw and place it against the antlers, at the point where the antlers meet the skull. Saw both the antlers off, while securing the skull so that it doesn’t move, altering the trajectory of the saw so that the cut is uneven.[1]
- Consider using a clamp to hold the skull in place, so that it doesn’t move while you saw it.[2]
-
Scrub the antlers with a wire brush. You need to remove all remaining organic material from the antlers. Scrub every part of the antler well, but give special attention to the area where the antlers met the skull cap. This is where hair and tissue are most likely to be hiding.[3]
- Wire brushes are available at most hardware stores. They are abrasive enough to pick up tissue without requiring too much force.
-
Boil the antlers outside. Fill a large cooking pot with water and, for best results, a pinch of salt. Allow it to reach a boil on a stove or a fire pit. Once it boils, submerge the entire antler in the cooking pot and allow to boil for 30 minutes.[4]
- This step is important for removing dangerous bacteria from the antlers.
- You should boil the antlers outside, otherwise they will stink up your house.
- Before beginning, test to see if the cooking pot is large enough to fit the antlers inside. All of the antlers should be submerged during boiling. If you don’t have any pots large enough, you can try using prongs to force them underwater or adjust them periodically during the boiling process.
-
Remove antlers from the boiling water after 30 minutes. Keep prongs on hand that you can use to remove the antlers without burning yourself. The antlers will feel soft when you pull them out of the cooking pot, but they will harden up after a few minutes.[5]
-
Allow the antlers to air dry for a day. Leave the antlers outside somewhere safe, where they will get sun and dry off. Do not, however, allow them to be out in the sun for more than 24 hours. The sun will erode the color of the antlers after more than a day of constant exposure.[6]
-
Apply water and soap to a towel. Too much water can damage the antlers, so be sure that the towel is only damp, not wet. Squeeze excess water out of the towel. Apply a nonabrasive soap—not bleach.
- Bleach and bleach-based cleaners can damage the antlers.
-
Scrub the antlers with the towel. Feel free to use force when scrubbing the antlers. Scrub until all dust and grime has been removed.[7]
-
Dry the antlers with a towel. You do not want the antlers to remain wet. Use a new towel that is dry to go over them, picking up excess moisture. It is alright if the antlers are still somewhat damp at the end of the process.[8]
Community Q&A
-
QuestionDoes boiling antlers take away from the aesthetics?.Community AnswerNo. Boiling not only improves aesthetics, but it removes the smell. If boiling alone does not work to your satisfaction, soak the antlers in water with added bleach.
-
QuestionI'd like to use antlers for dog chews. How long should they be cut?Community AnswerI do not advise using deer antlers as dog chews. Bone splinters, depending on the age of the antlers, could possibly harm your pet. A better idea would be to ask your butcher for suitable bones for your dog to gnaw on.
-
QuestionWe have antlers that were placed in a rusty container. They are now very orangey-brown. What is the best way to clean them to get off the rust?Community AnswerRust-covered deer antlers can be whitened by soaking in water plus bleach. I tend to be heavy-handed with bleach, but it won't dissolve the bone.
Tips
References
- ↑ http://deerhuntingfield.com/efficiently-clean-deer-antlers/
- ↑ http://goneoutdoors.com/clean-deer-antlers-4881647.html
- ↑ http://deerhuntingfield.com/efficiently-clean-deer-antlers/
- ↑ http://deerhuntingfield.com/efficiently-clean-deer-antlers/
- ↑ http://goneoutdoors.com/clean-deer-antlers-4881647.html
- ↑ http://deerhuntingfield.com/efficiently-clean-deer-antlers/
- ↑ http://deerhuntingfield.com/efficiently-clean-deer-antlers/
- ↑ http://deerhuntingfield.com/efficiently-clean-deer-antlers/
About This Article
Cleaning a new set of deer antlers that you picked up on a hunt can seem a bit labor-intensive, but the entire process shouldn’t take more than an hour. Use a hacksaw to saw both antlers off where they meet the skull. To remove any organic material, scrub them with a wire brush, giving special attention to the area where the antlers meet the skull cap. After giving them a good scrub, fill a large pot with water and a pinch of salt, bring it to a boil, and submerge the antlers. Allow them to boil for 30 minutes to remove any bacteria. Once your antlers are clean, allow them to air dry in the sun for a day. To learn how to perform regular maintenance on your deer antlers, keep reading!