PDF download Download Article
The best tools and methods for creating holes in plexiglass
PDF download Download Article

Plexiglass, also known as Lucite and Perspex is a type of acrylic.[1] Drilling through Plexiglass is notorious for causing it to crack, but with a round drill bit and low drill speed, this should be a breeze. Just take your time and make sure you have the right equipment. Here, we’ll walk you through the entire process so that you can drill clean, smooth holes without damaging anything.

Things You Should Know

  • Put scrap acrylic or MDF sheets behind the Plexiglass you’re drilling to brace it and minimize cracking.
  • Use a spiral drill bit designed specifically for plastic to slowly drill through the Plexiglass at the lowest drill speed.
  • Use short bursts of low surges until the hole is drilled. If you smell burning, pour water on the hole as you drill.
Part 1
Part 1 of 3:

Safety & Setup

PDF download Download Article
  1. Wear safety goggles. Acrylic can chip quite easily if you aren’t careful, so protect your eyes with protective goggles. If you’re working in an enclosed space with no ventilation, put on a dust mask or respirator, too.
    • Drilling Plexiglass isn’t bad for your lungs, but the aroma of the melting acrylic from the drilling can be kind of unpleasant if you’re sensitive to strong odors.
  2. Acquire some spiral drill bits designed for plastic. Plexiglas, the company that makes Plexiglass, explicitly says spiral bits are ideal when it comes to drilling through their products.[2] These bits have a different geometric structure that digs through acrylic more easily, so they’re less likely to crack the Plexiglass. Attach the bit to whatever drill you’re using based on the size of the hole you’re making.[3]
    • Any drill will work with Plexiglass. You don’t need to use any special tools for this.
    Advertisement
  3. Practice with smaller pieces of scrap acrylic before attempting to drill into a large sheet. This will help you get a sense for the ideal speed. The hardest part of this process is getting the speed right, since too slow will cause the bit to skid while too fast will cause cracks.[4]
  4. Advertisement
Part 2
Part 2 of 3:

Preparing and Aligning the Drill Point

PDF download Download Article
  1. Set the acrylic you’re going to drill through on top of a sheet of damaged Plexiglass or MDF (medium density fiberboard). This will make it less likely that you will chip the back of the board or scratch it when the drill bit goes through.
    • Some DIY enthusiasts have a lot of success putting painter’s tape around the sides of the area they’re drilling through.
    • If there’s a protective film on the Plexiglass, leave it on. It’ll help minimize the odds of a crack.
  2. Use as many clamps as is necessary to secure the sheet. For larger sheets, you may need as many as 3-4 clamps. You can secure the sheets between two tables, two sawhorses, or even a single saw table.
    • If you have adjustable C-clamps with custom pressure settings, don’t overdo it. So long as the Plexiglass is stable, it’s fine. If you over-tighten the clamps, you could shatter the sheet.
  3. Use a dry erase or permanent marker to indicate where you’re going to drill, since it can be kind of tough to stick to a spot on the clear Plexiglass. Also, make sure that the hole you’re drilling isn’t within 3–5 inches (7.6–12.7 cm) of the edge of the sheet. Acrylic is notorious for chipping near the edge when it is punctured.[5]
    • If you do need to drill near the edge, sandwich the acrylic between multiple sheets of MDF or acrylic and only leave the edge exposed.
    • Acrylic and Plexiglass can be kind of hard to drill through since there are no points of reference. Marking the spot will help you keep track of where you’re working.
  4. Advertisement
Part 3
Part 3 of 3:

Driving the Drill Through

PDF download Download Article
  1. Plug your drill in or place a charged battery inside. Then, turn the dial on the front of the drill to one of the lower numbers (if you have options from 20-1, 5 or under are ideal settings. Test the drill to confirm the drill bit is seated perfectly in the chuck.
    • If the drill bit isn’t seated perfectly, unlock the chuck by twisting it counterclockwise and retighten it.
  2. Hold the drill steady over the mark you made at as perfect a 90-degree angle as possible. Maintain a moderate amount of pressure and slowly squeeze the drill. Work slowly in short bursts to ensure you don’t crack the acrylic.[6]
    • If the drill bit skids, just reset and realign your drill bit against the Plexiglass.
  3. Aim for a calm penetration rate as you continue to drill. Acrylic drill bits will produce plastic shavings, so once they start to surround the drill bit, stop and remove them to get a better view of what you are doing.[7]
    • You can actually tell if you’re drilling at a healthy speed and energy by the shavings. If the shavings come off in thin, coherent sheets like you’re sharpening a pencil, you’re good to go.
  4. Plexiglass gets very hot when you drill into it, so it may start to melt if you’re drilling through anything thicker than a fraction of an inch. If you notice the area around the hole you’re drilling melting or you smell burning, stop and pour room-temperature water over the hole.
    • Keep working until you’ve punched out the hole and repeat the process as needed!
    • If your hole is too rough for your liking, deburr it by drilling through the hole again from the opposite side or by smoothing the inside down with sandpaper.
  5. Advertisement

Community Q&A

Search
Add New Question
  • Question
    Is there a special bit needed to drill plexiglass?
    Community Answer
    Community Answer
    There are special drill bits. They aren't "needed," but they are helpful and do a better job.
  • Question
    How do I cut a square in the middle of a Plexiglas sheet?
    Community Answer
    Community Answer
    You'll need a hand saw with a removable blade (like a hacksaw) and a drill bit that is a slightly larger diameter as the saw blade. Sketch the square in the location you want it on the material, then drill into the four corners of the square, taking care to make sure the hole doesn't cross over the square boundary you drew. Next, fit the blade through the hole and proceed to cut along the lines you've drawn. Cut the square a bit smaller than your final dimensions so you can go back with some sandpaper to clean up the cut, and use a sharp blade (use gloves!) to deburr and/or cut a chamfer into the edges.
  • Question
    If I glue the plexiglass to the wood strip first, will that keep it from breaking when I drill it?
    Community Answer
    Community Answer
    The trick is to go slowly, use a good sharp bit, and ensure that the section of material you are drilling is supported and will not bend, twist, or otherwise deviate from "flat". You could drill progressively larger holes, but in my experience this can cause chipping around the edges of the hole. Simply drill with the exact size you want, go slowly, and keep the cutting tool as close to perpendicular as you can.
See more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

  • It is possible to drill acrylic with regular metal drill bits. However, the likelihood of melting, chipping, cracking, or breaking the acrylic is much higher. Ensure you go slow, stop often to cool the drill and always support the sheet.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Things You'll Need

  • Safety goggles
  • Round drill bits
  • Clamps
  • Medium Density Fiberboard (optional)

About This Article

Jason Phillip
Co-authored by:
Handyman
This article was co-authored by Jason Phillip and by wikiHow staff writer, Eric McClure. Jason Phillip is a handyman and owner of Iconic Interior Installations based in New York City, New York. With over five years of experience professionally mounting and installing objects through his company, Jason's work includes mounting window AC units, designing art gallery walls, installing kitchen cabinets, and replacing light fixtures on drywall, brick, and plaster. He has been rated a "Top Pro" every year since 2016 by Thumbtack for being one of the highest-rated, most popular professionals on Thumbtack. This article has been viewed 328,938 times.
3 votes - 67%
Co-authors: 9
Updated: February 4, 2024
Views: 328,938
Thanks to all authors for creating a page that has been read 328,938 times.

Reader Success Stories

  • Sandy M.

    Sandy M.

    Jun 5, 2017

    "It was important to find out that I would need special drill bits and that I would have to make sure that they..." more
Share your story

Did this article help you?

Advertisement