PDF download Download Article PDF download Download Article

Garlands come in a variety of different styles and make excellent Christmas decorations. If you want to hang garland on a brick wall, there are several methods that you can use. If you have evenly-spaced bricks and don’t want to damage your wall, hang brick clips on raised bricks to attach your garland. If the wall contains bricks of different sizes but you still don’t want to drill holes, you can use adhesive hooks to hang garland on brick. If you don’t mind drilling, you can always install wall anchors and screws in the mortar between your bricks to hang garland.

Method 1
Method 1 of 3:

Using Adhesive Hooks

PDF download Download Article
  1. Adhesive hooks, or command strips, are plastic strips with hooks on them that have a strong adhesive on the back. Most adhesive hooks are designed to hold less than 20 pounds (9.1 kg), so make sure that you get some heavy-duty clips if you’re hanging a heavy or large garland. Read the label on a package carefully to ensure that the adhesive on the back will work with brick.
    • Adhesive hooks are the best option if you don’t want to drill into brick but you can’t find brick clips that match your brick pattern.
    • Purchase some adhesive hooks from your local hardware or big box store. They can also be purchased online.

    Tip: Some adhesive hooks are not designed to be removed. Purchase permanent hooks if you plan on leaving a garland up for a longer period of time.

  2. Place at least 1 hook for every 2–6 feet (0.61–1.83 m) of garland. Use a measuring tape to space out each hook equally if you’re going for a symmetrical look by measuring the same distance between each of your hooks. Hold a level between potential hooks to determine if a location is even by checking the air bubble in the level. Mark the location for each hook with a pencil.[1]
    • Different adhesive hooks have different weight thresholds, usually between 2–30 pounds (0.91–13.61 kg) each. The higher the weight threshold for a set of hooks is, the further apart you can place them.
    Advertisement
  3. For each location that you’ve marked off, peel off the cover for the adhesive tape on the back of each hook with your fingernail. Hold the hook up against the brick to position it and slowly lower it against the wall.[2]
    • The cover for the tape should come off relatively easily, but if it doesn’t, use a small knife to peel the corner open.
    • If you misplaced the hook but you haven’t pressed down yet, you may be able to reposition it.
  4. Once you’ve positioned a hook, place both hands on the opposite ends of the hook so that one is on the top of the hook and one is on the bottom. Apply equal, firm pressure into the hook for 5-10 seconds to adhere it to the brick.[3]
  5. Run the garland’s center branch or twine over each of the adhesive hooks. Start in the middle so that you can adjust each side to make it even. If you ever need to remove or adjust any of the hooks, you can either pull on the tab in the bottom of the hook, or use a dull knife to pry it off from the bottom.[4]
    • Some hooks come with small strips that stick out of the bottom to remove them. Pull this strip directly down to remove a hook.
    • If there isn’t a removal strip attached to the hook, use a flat, dull kitchen or putty knife to get leverage under the hook. Pry it up 1-2 millimeters and then remove the hook by pulling it off.
  6. Advertisement
Method 2
Method 2 of 3:

Hanging a Garland with Brick Clips

PDF download Download Article
  1. If the bricks on your wall stick out at least 14 in (0.64 cm) past the mortar, you can hang clips around the bricks to hang your garland. Brick clips hook around the edges at the top and bottom of a brick and rely on the brick’s weight to keep the clip in place. However, if the mortar is flush with your bricks, there won’t be enough room to hang the clips.[5]
    • Brick clips are an excellent option if you don’t want to drill into the mortar or put any adhesive material directly on to your brick.
    • Brick clips will only allow you to hang a garland horizontally if your bricks are in even rows.
  2. Measure the height of a brick on the wall where you plan on installing or hanging the garland. You can purchase brick clips from a local hardware store or online retailer. They come in different sizes, so read the label on a package carefully to ensure that the clips are designed for bricks that are the same size as the bricks in your wall.[6]

    Tip: Brick clips can usually be adjusted to fit a range of 0.2 inches (0.51 cm) in either direction, so if your brick’s height is 3 inches (7.6 cm), you can likely use brick clips designed for bricks that are 2.8–3.2 inches (7.1–8.1 cm).

  3. Hold the brick clip slightly above the brick you’re attaching it to and slide it down so that the top of the clip is on top of the brick. Once the top of the clip is hanging on the top of a brick, slide the bottom under the bottom of the brick. Most brick clips will snap into place under the brick. Install each brick clip so that the hook on the face of the clip is facing up.[7]
    • It’s easy to reposition a brick clip if you don’t like how it’s placed. Pop it off of a brick by pulling the bottom down while pulling it off.
    • Use a stable ladder to reach bricks that are high off of the ground.
  4. You can arrange your hooks however you’d like. If you’re hanging the garland around a door or fireplace, place 2 symmetrical hooks above fixture or door. If you’re hanging the garland horizontally, place all your clips along the same row of bricks. The amount of space you leave between clips will determine how many dips there are in your garland.[8]
    • For example, if you use 3 brick clips, you will have 3 distinct dips in the garland on the wall where you’re installing it. The more clips you add, the less distinct the dips will be.
  5. Start with the centermost hook and run the garland through the hook on the brick clip. While it is hanging on the centermost hook, adjust the length hanging off of each side by carefully pulling on an end to make the garland center.[9]
    • If the hooks on the brick clips are too big for the twine of your garland, leave 2–4 feet (0.61–1.22 m) of garland hanging off of each clip on both ends. The weight from the garland will keep the rest of the twine or branch in place.
  6. Advertisement
Method 3
Method 3 of 3:

Drilling Masonry Screws or Hooks into Mortar

PDF download Download Article
  1. If you want your hooks or screws to be symmetrical, use a measuring tape to place your marks in equidistant intervals. If you plan on using hooks to hang your garland, keep each screw location on the same horizontal plane by using a level to ensure that each gap is even and flat.[10]
    • You can use any kind of pencil to mark the location of each screw.
  2. You can purchase hooks, anchors, and screws at a local hardware store or online. Choose hooks or screws that will fit between your bricks without touching them. In most cases, a screw with a 14 inch (0.64 cm) head will be perfect. Screws and hooks should fit at least 1 12 inches (3.8 cm) into the mortar.[11]
    • Check a package of wall anchors to ensure that it will fit the threading of your screw. Most wall anchors will fit several types of screw though.
    • If your garland is under 3 pounds (1.4 kg), you don’t need to use wall anchors. Unless your garland weighs more than 30 pounds (14 kg), any plastic wall anchor that fits your screw will work.
    • Hooks are better for garlands with thicker leaves or tinsel.
  3. Before you drill into your brick wall, set out a drop cloth along the wall where you plan on drilling. If there is any furniture along the wall, you can either move it out of the way, or cover it. Drilling into mortar will send dust flying all over the place, and cleaning it up can be a pain if you don’t have a drop cloth.[12]

    Warning: Do not drill directly into your brick. You could risk splitting the brick, and mortar is easier to fill in if you ever want to repair your holes. Always wear protective eyewear, a dust mask, and gloves when drilling into mortar. The dust can be a lung and eye irritant.

  4. Hold a masonry drill bit up to the length of your wall anchor until you’ve found a bit that is at least 132 inch (0.079 cm) thinner than the wall anchor. Attach the drill bit to your drill by unscrewing the bolt at the top and sliding it in. Drill a pilot hole that is at least half of the length of your wall anchor into each location where you want to add a screw or hook.[13]
    • A pilot hole refers to any incision that you make so that a screw or fixture can be screwed in more easily.
  5. Use a screwdriver or drill with a fitted drill bit to screw each wall anchor into a pilot hole. Drill each wall anchor in so that it is flush with the mortar.[14]
    • You can use a can of compressed air to blow away any mortar dust if you’d like. This will keep the anchors from shedding dust particles over time.
  6. Drill your screws into the wall anchors so that 1–3 inches (2.5–7.6 cm) of the screw are sticking out. If you are installing hooks, screw the threaded side into the wall anchor by hand and stop once the threading is hidden in the wall. Rotate the open end of each hook until it is pointing up towards your ceiling.[15]
  7. Start in the centermost hook so that you can adjust the length on both sides to make it even. If you’re hanging the garland with hooks, run the center of the garland through the center of each hook. If you’re hanging the garland over the screws, balance the twine of the garland over the screw where it meets the wall. If there are loops in the garland’s twine, you can loop them around each screw and then drill the screws in all the way to hide the anchors.[16]
    • If you find your garland slipping off of a hook, consider wrapping the garland around the hook or taping a leaf or branch to the top of the screw. Garlands aren’t typically very heavy, so it won’t take much tape to keep garland hanging.
    • You can always fill in holes in the mortar by mixing water and mortar in a bucket or tray and use a trowel to apply it.
  8. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Things You’ll Need

  • Ladder
  • Measuring tape
  • Level
  • Pencil

Hanging a Garland with Brick Clips

  • Brick clips

Using Adhesive Hooks

  • Adhesive hooks

Drilling Masonry Screws or Hooks into Mortar

  • Drill
  • Protective eyewear
  • Dust mask
  • Gloves
  • Wall anchors
  • Screws or hooks

You Might Also Like

Advertisement

About This Article

Peter Salerno
Co-authored by:
Installation Expert
This article was co-authored by Peter Salerno and by wikiHow staff writer, Eric McClure. Peter Salerno is the owner of Hook it Up Installation, a professional installation company, which has been hanging art and other objects around Chicago, Illinois for over 10 years. Peter also has over 20 years of experience installing art and other mountable objects in residential, commercial, healthcare and hospitality contexts. This article has been viewed 88,016 times.
4 votes - 75%
Co-authors: 6
Updated: April 27, 2024
Views: 88,016
Thanks to all authors for creating a page that has been read 88,016 times.

Reader Success Stories

  • Lynda Waldmann

    Lynda Waldmann

    Nov 10, 2021

    "Im 74 and I wanted to decorate for Christmas. My husband usually did these things but sadly passed away two years..." more
Share your story

Did this article help you?

Advertisement