How to Hang a Curtain Swag

Co-authored by Garrison Hullinger and Kyle Hall

Last Updated: November 18, 2021 References

Whether it's traditional or scarf-style, a curtain swag can make your window look more formal and elegant. To hang up a curtain swag, you'll just need a curtain rod, a couple brackets, and a drill. Once you have all your supplies, putting up the swag is a breeze!

Part 1

Part 1 of 3:

Choosing Rods and Brackets

Download Article

^{[1]
X
Expert Source

Garrison Hullinger
Interior Designer

Expert Interview. 11 November 2021.} If you’re just going to have the swag over the window without any curtains, single curtain rod brackets are the way to go. Single brackets will hold up 1 curtain rod, which is all you need for the swag.^{[2]
X
Research source}
2
Get double brackets if you want to hang curtains up with the swag. Double curtain brackets come with 2 slots instead of 1 so they can hold 2 curtain rods. If you want to hang up regular curtains that you can open and close along with the swag, you’ll need to use 2 rods.^{[3]
X
Research source}
- The swag will go on the front rod, and the curtains will go on the back rod.
Advertisement
^{[4]
X
Expert Source

Garrison Hullinger
Interior Designer

Expert Interview. 11 November 2021.} To measure the width of the window, take measuring tape and measure from the outer edge of the window frame on the left side of the window to the outer edge on the right side of the window. Write the measurement down so you have it when you're shopping for curtain rods.
4
Get a rod that's at least 2 inches (5.1 cm) longer than the width. Traditionally, curtain rods extend further than the width of the window. The more the curtain rod extends over the sides of the window, the larger the window will appear. If you want to make the window seem bigger, choose a rod that's up to 1 foot (0.30 m) longer than the width of the window.
- Avoid using a rod that's not at least 2 inches (5.1 cm) longer than the width of the window frame or it could be too short.
- Don't use a rod that's longer than 1 foot (0.30 m) or it could look too long above the window.
5
Use a decorative or cafe curtain rod for your swag. Both decorative and cafe curtain rods can hold a swag, whether it's scarf-style or made with a rod pocket. If you're using a particularly heavy swag, you may want to go with a decorative rod since they're sturdier.
- Avoid using a traverse curtain rod for your swag. Traverse curtain rods are designed to hold curtains that have pins that hook into the rod. Since curtain swags don't have these pins, a traverse rod won't work.^{[5]
  X
  Research source}

Part 2

Part 2 of 3:

Installing the Brackets

Download Article

1
Mark 4–8 inches (10–20 cm) above your window on either side. This is the level you’ll hang the curtain brackets at. The higher you hang the brackets, the larger your window will appear. Avoid hanging the brackets more than 8 inches (20 cm) above your window or your swag may look too high.^{[6]
X
Research source}
- Make the marks with a pencil so they’re easy to erase.
- Don't hang the brackets less than 4 inches (10 cm) above the window or it may look too crowded.
2
Hold the brackets on the wall above the frame and mark the screw holes. You want 1 bracket on either side of the window frame. Hold them so the screw holes are level with the marks you made earlier.^{[7]
X
Research source}
- Make sure the distance between the brackets isn’t greater than the length of the curtain rod or else the rod won’t fit. Use a tape measure to measure the length of the rod and then measure the distance between the brackets. If the distance between the brackets is greater, move them closer in toward the frame.
Place the level between the bracket marks so the top edge is lined up with the each of the marks. Then, check the gauge in the center of the level — if the air bubble is outside of the marked lines, the bracket marks aren't level. If that's the case, redraw the bracket marks so they're level with each other.
A pilot hole is a pre-drilled hole that makes it easier for screws to go into a surface. To drill the pilot holes, use a drill bit that’s slightly smaller than the screws that came with the brackets. Drill into the screw hole marks you made on both sides of the window.^{[8]
X
Research source}
Hold the brackets on the wall so the screw holes are lined up with the pilot holes you drilled. Then, drill the screws that came with the brackets through the holes until the brackets are secure.^{[9]
X
Research source}

Part 3

Part 3 of 3:

Putting up the Rod and Swag

Download Article

1
Slide the swag onto the curtain rod if it has a rod pocket. Rod pocket curtain swags have a pocket along the top edge that slides onto the rod to hold the swag in place. If your swag has a rod pocket, slide it onto the end of the curtain rod. Then, center the swag on the rod so the front of the swag is facing out.^{[10]
X
Research source}
- If you’re not using a rod pocket swag, you can skip this step.
2
Wrap the swag around the curtain rod if it’s a scarf-style swag.^{[11]
X
Expert Source

Garrison Hullinger
Interior Designer

Expert Interview. 11 November 2021.} Scarf-style curtain swags don’t have a rod pocket. Instead, wrap the fabric around the curtain rod so it drapes like a regular swag. Start by hanging one end of the swag over one end of the rod. Then, hang the other end of the swag over the other end of the rod. Let the fabric in the middle drape down.^{[12]
X
Research source}
- When you’re finished, the draped fabric in the center should look like a regular curtain swag.
- With a scarf-style swag, you can experiment with different wrapping techniques until you find something you like. For example, you can wrap the swag so it's asymmetrical, with one end of the fabric hanging down further than the other end.
Put the curtains on the second curtain rod if you're hanging any. Attach the curtains to the second curtain rod using the rod pocket, holes, or clips that the curtains came with. When you're finished, there should be 2 curtain panels on the rod.
4
Mount the curtain rod in the brackets.^{[13]
X
Expert Source

Garrison Hullinger
Interior Designer

Expert Interview. 11 November 2021.} Set the ends of the rod in the bracket holders so the rod is centered over the window. If you’re using double brackets with 2 rods, mount 1 rod in the back bracket holders and the other rod in the front bracket holders.
- With double brackets, the rod with the swag should be in the front and the rod with the curtains should be in the back.
5
Adjust and center the curtain swag. If you're using a rod-pocket swag, make sure it's slid all the way to the center of the rod. Also, check to make sure there aren't any parts of the rod pocket that are bunched up — if there are, smooth them out with your hands.
- If you're using a scarf-style swag, make sure the draped part of the fabric is centered on the rod.

Community Q&A

Search

Add New Question

Question

What if I have a curtain rod and an extra one for the swag that fits over the curtain?

Pat morneau

Community Answer

Unless you put swag in middle of two curtain sides, swag will blend in.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 0 Helpful 1
Question

How can I hang swag without using a pole?

Pat morneau

Community Answer

Hang the top of swag over the top of the curtains. You may have to pin swag to curtains to keep it from slipping down.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 4 Helpful 5
Question

Should I steam a new swag before hanging it, steam it in place, or both?

Rodd Cohen

Community Answer

Steam in place so you can hand dress it. Often valances require other invisible support such as Velcro, tape, or pins which is not evident until it is hung in place.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 0 Helpful 0