PDF download Download Article PDF download Download Article

DVDs are ubiquitous in the entertainment world today, and DVD players can be purchased for less than the price of a nice dinner. Hooking up a DVD player to your TV will give you access to countless hours of movie-watching bliss, and most modern TVs and DVD players make the setup process a breeze.

Setting Up a DVD Player

Plug the HDMI cable into the television, then plug the other end into the DVD player. Plug the DVD player's power cord into the wall, then press the "Power" button on the player and TV. Change your TV's input mode to the appropriate HDMI port.

Method 1
Method 1 of 5:

Powering On the DVD Player

PDF download Download Article
  1. Before trying to hook up your player, make sure it is plugged in and turns on when you press the "power" button. Usually, a small light or welcome message appears when the DVD player is working correctly.
  2. There are at three common ways to connect a DVD player, and each needs a different cable to work. Your DVD player should come with all of the appropriate cords, but you need to check which connections your TV accepts as well. Look into your owner's manuals or check the TV and DVD Player yourself to see what connections you can use. The three most common are.
    • HDMI: The most modern connection, HDMI resembles a longer, thinner USB cord. HDMI connections are the highest quality connections and you only need one cord for both the audio and video.
    • A/V Cables (Three-Prong): Standing for Audio/Visual cables, this is the most common connection for DVDs. There are three prongs at either end-- red, yellow, and white -- and they match up to corresponding colored inputs on both the TV and DVD player.
    • Component Cables: Sporting better quality than A/V cables but less than HDMI, component cables are a set of five colored prongs attaching to five matching inputs on both the TV and the DVD player.
    Advertisement
  3. Once you know what connection you will use, locate the cable and make sure it is not torn or frayed. If you need a new cable, or are missing one, take a picture of the input you want and bring it to your local electronics store to find a replacement.
    • If possible, use an HDMI cable, as they are the easiest to install and have the best quality video.
  4. Once you know what connection you will need, make sure you put the DVD player close enough to the TV so that you can reach the appropriate cables to the back.
    • Do not stack different electronic equipment on top of one another -- they can quickly heat up when in use and damage the electronics.
  5. This prevents the likelihood of electric shocks and protects the equipment.
  6. Most projectors have the same set of inputs as TVs, so don't be intimidated if you want to hook up a projector instead.
    • Some projectors use a "DVI Input" instead of the three connections listed above. If so, follow the same procedure as "Connecting with an HDMI Cable," substituting a DVi cable for an HDMI.[1]
  7. Advertisement
Method 2
Method 2 of 5:

Connecting with HDMI Cable

PDF download Download Article
  1. Look for the "HDMI" or "HDMI Out" label and fit the cable securely into the socket.
    • This is the highest quality connection for audio and video and is typically found only on modern DVD players.
  2. Just like DVD players, only newer TVs have HDMI sockets. There may be multiple sockets available. Each HDMI socket will be labeled "HDMI" or "HDMI In" along with a potential input number.
    • If there is an input number, like "HDMI 1," remember it for later. This is the setting your TV must be set at to see your movies.
  3. An HDMI connection only requires one cable that carries both audio and video signal, and it does not matter which end goes where. But if the cable is pulled too tightly, or one of the connections is loose, you may not get a good signal.
    • There are a lot of different HDMI cords available, but unless you want a pristine, perfect picture then any length and type of cord will work just fine as long as it reaches.[2]
  4. Insert a DVD so that you can test both the picture and the audio.
  5. Sometimes labeled "input," this button allows you to switch where your TV gets the video and sound information. The input you choose on the TV should match the input you used for the cables.
    • If there is no label or you don't know what input to use, leave the DVD player on and test each input for 5-10 seconds to see where the video appears.
  6. Advertisement
Method 3
Method 3 of 5:

Connecting with A/V Cables

PDF download Download Article
  1. The sockets are color-coded to match the cable (Red, White, and Yellow). Look for the "Output" or "Out" group. The Red and White sockets (Audio) may be separated from the Yellow one (Video).
    • The set of sockets are typically grouped together with a border or line indicating the included sockets.
  2. Like on the DVD player, these will be color-coded to match the cable and grouped into input groups. Look for the "Input" or "In" designation. A/V inputs are typically numbered to indicate which input you will need to select on the TV.
    • The input sockets are usually grouped together, and are often marked by a border or a line separating the group from the other Inputs.
    • The Red and White sockets (Audio) may be separated from the Yellow one (Video). The labels should indicate which socket goes with which Input.
  3. Match the colored plugs on the cable to the colored sockets on both the DVD player and TV.
    • The Yellow video plug may be a separate cable from the Red and White audio cable.
  4. Insert a DVD so that you can test both the picture and the audio.
  5. Sometimes labeled "input," this button allows you to switch where your TV gets the video and sound information. The input you choose on the TV should match the input you used for the cables.
    • If there is no label or you don't know what input to use, leave the DVD player on and test each input for 5-10 seconds to see where the video appears
  6. If you are only getting video or only getting audio, or you aren't getting any signal at all, your cable may be plugged in incorrectly. Check to make sure that each colored plug is attached to the correctly colored socket.
    • If the video is not showing up, ensure that the Yellow plug is connected to the correct Input on the TV and Output on the DVD player.
    • If the audio is not coming through, ensure that the Red and White cables are plugged into the correct Input on the TV and the correct Output on the DVD player.
  7. Advertisement
Method 4
Method 4 of 5:

Connecting with Component Cables

PDF download Download Article
  1. The sockets are color-coded to match the cable (Green, Blue, Red, White, Red) and are typically grouped and labeled. Look for the "Output" or "Out" group. The Green, Blue, and Red sockets (Video) may be separated from the Red and White pair (Audio), so make sure all five cords are plugged in.
    • You will notice that a component cable has two Red plugs, which can make things confusing. To figure out which is which, lay the cable out flat so that all of the prongs line up. The order of colors should be Green, Blue, Red (video), White, Red (audio).
    • Some component cables only have the Green, Blue, and Red video plugs. You will need a separate Red and White plug audio cable in order to hear your DVDs, like the one found in the A/V section above.
  2. Like on the DVD player, these will be color-coded to match the cable and grouped into Input groups. Look for the "Input" or "In" group. They are typically numbered to indicate which Input you select on the TV.
  3. Match the colored plugs on the cable to the colored sockets on both the DVD player and TV.
  4. Insert a DVD so that you can test both the picture and the audio.
  5. Sometimes labeled "input," this button allows you to switch where your TV gets the video and sound information. The input you choose on the TV should match the input you used for the cables.
    • If there is not a label or you don't know what input to use, leave the DVD player on and test each input for 5-10 seconds to see where the video appears
  6. If you are only getting video or only getting audio, or you aren't getting any signal at all, your cable may be plugged in incorrectly.
    • If the video is not showing up, make sure that the Green, Blue, and Red video cables are plugged into the correct Input on the TV and the correct Output on the DVD player.
    • If the audio is not coming through, ensure that the Red and White cables are plugged into the correct Input on the TV and the correct Output on the DVD player.
    • Double check that the Red cables are plugged into the correct sockets. If they are in the wrong ones, both the audio and video will be messed up.
  7. Advertisement
Method 5
Method 5 of 5:

Troubleshooting

PDF download Download Article
  1. DVD players need a power source in order to work, so double-check that the player is plugged into the wall or a power strip.
  2. DVD players will display on one of the Input or Auxiliary channels. They will not show up on Channel 3 or 4 like some VCRs.
    • Some TVs will label the Input channels based on the type of input, such as "HDMI", "AV", and "COMPONENT." Refer back to Method one if you have a question about which input type you are using.
  3. Sometimes, old cables can become frayed and the plugs can start coming loose. This can lead to a poor or nonworking connection. Try a new cable to see if your problem can be fixed.
    • Note: There are a lot of companies that market extremely expensive cables. For the most part, you will not see any significant difference using high-end cables. This is especially true for HDMI, where a $5 cable will perform the same as an $80 cable.[3]
  4. Advertisement

Community Q&A

Search
Add New Question
  • Question
    Why is my DVD player in black and white?
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer
    This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer
    There are several possibilities here. One is that you’ve not connected the cables properly; check that the cables match the color coded jacks they’ve been attached two. The second possibility is that there is a fault with the chroma signal due to either the connections or chipset having a fault. The third possibility is that the color saturation on your display has been turned down to black and white by mistake––unusual but worth checking. Or, finally, you may have inserted a black and white DVD, somewhat common with older TV shows and movies that you expected to be in color or colorized but were not.
  • Question
    How do you hook up a DVD player to a smart TV?
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer
    This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer
    You’ll need to hook up the DVD player to a smart TV using either an HDMI, composite, component or S-Video cable. The instructions accompanying your new smart TV should make it clear which is the correct cable and will also explain how to place the cables into the sockets of both devices. Once connected, you need to select the proper source or “input” on your TV to be able to view the DVD player for use. Detailed instructions for one type of smart TV, a Samsung TV, can be found here: How to Connect a DVD Player to Samsung TV.
  • Question
    Can I plug yellow into green?
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer
    This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
    wikiHow Staff Editor
    wikiHow Staff Editor
    Staff Answer
    In some of the newer TVs, there isn’t a standard White, Red, Yellow socket sequence; rather it may be White, Red, Green. The thing to try here is to see if the Green socket is either labeled Video (above or below), or has a yellow line around the green. Either of these indicates that it is okay to use the Green socket for the Yellow component. Test the connection by switching on both the TV and DVD player; you might need to cycle through the TV input channels via your remote to fine tune the color.
See more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

  • The DVD player will most likely come with a "Quick Start Guide", which will provide basic instructions on how to set up the DVD player and start using it.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

About This Article

wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 48 people, some anonymous, worked to edit and improve it over time. This article has been viewed 1,985,070 times.
How helpful is this?
Co-authors: 48
Updated: September 27, 2024
Views: 1,985,070
Article SummaryX

1. Determine which type of connector you’ll use.
2. Connect the necessary cable from the player to the TV or receiver.
3. Connect audio cables if desired.
4. Turn the DVD player and TV on.
5. Use the TV remote to switch the ″source″ to the DVD player.

Did this summary help you?

Thanks to all authors for creating a page that has been read 1,985,070 times.

Reader Success Stories

  • Ms. Chappell

    Ms. Chappell

    Feb 4, 2017

    "The detail your article gave helped tremendously. I read the DVD player's installation guide thoroughly, but,..." more
Share your story

Is this article up to date?

Advertisement