PDF download Download Article PDF download Download Article

Gas dryers offer a more energy efficient means of drying clothes than electric dryers, but they are more challenging to install. Knowing the proper tools and connections to use are critical to successfully installing a gas dryer. Before installation, make sure your dryer is compatible with your home. Connect the gas line and exhaust vent correctly, and take proper steps to finish the installation.

Get Product Support Solve Any Problem

wH
Hi there! Do you have a question about how to use or repair your home appliance? I’ve read the manuals so you don’t have to. Select your product, brand, and model, then ask away!
*
*
Part 1
Part 1 of 4:

Making Sure the Dryer Works with Your Home

PDF download Download Article
  1. Most new gas dryers use 120 volts of electricity. Make sure your home supports this. Some older homes only offer 110 volt service, while most modern homes are equipped to support 240 volt service. Check your circuit breaker to make sure you have two columns of 120 volt circuits.[1]
    • If you’re not sure what to look for, ask a qualified electrician to look at your circuit breaker and make sure that your home can handle a 120 volt dryer.
  2. The vent on your dryer needs to match up with the one in the wall in your laundry room. Most exhaust vents are 4 inches (10.16 cm) in diameter.
    • If the vent in your dryer does not match the one on your wall, you should be able to purchase a vent adapter or transition pipe at a hardware or home supply store.
    Advertisement
  3. Your gas dryer will need an appropriate gas hookup. The gas line should have a supply valve in the same room where you intend to install the dryer, preferably within 6 feet (1.8 m) of the unit.[2]
    • If there is no gas pipe in the laundry room, you will have to have one installed by a qualified technician.[3]
  4. Advertisement
Part 2
Part 2 of 4:

Connecting the Gas Supply

PDF download Download Article
  1. The breakers can be turned off at the main breaker panel. The location of this varies from home to home, but they are usually found in the garage or basement for houses and in utility closets or bedrooms for condos and apartments. The gas valve can be turned off at the supply valve for the dryer’s gas pipe, or at the main gas service shutoff valve.[4] The location of the main shut off valve varies from home to home.
    • In many homes, the gas valve can be turned off by using a 12 to 15 inch (30.5 to 38.1 cm) adjustable wrench. Turn the valve until the tang (handle you attach the wrench to) is perpendicular to the pipe.
    • If you are unsure of how to turn off the gas valve, contact your gas supplier.
  2. Before connecting the piping on your dryer to the gas pipe in your wall, you will need to coat all threaded connecting pieces with a pipe thread compound. This will help create a good seal between the pipe components and prevent dangerous gas leaks.[5]
    • Look for a pipe thread compound designed for use with liquid petroleum gas (LPG) at your hardware or home supply store.
  3. Fasten a flexible connector with stainless steel fittings to the gas pipe on the dryer. These are sometimes included when you purchase a dryer, or you can find them at your local hardware store. Explain what you are doing and the store employee should be able to help you find what you're looking for.
    • You may need an adapter to attach the 3/4 inch (1.9 cm) end of the pipe connector to the 3/8 inch (1 cm) pipe end on the dryer.
    • Make sure your connector is long enough to connect your dryer to the pipe in your wall.
    • Do not attempt to reuse an old pipe connector! If you are replacing a previously installed gas dryer, throw away the old connector and replace it with a new one.
  4. Once you’ve hooked the pipe connector to the pipe on the dryer, connect the other end to the gas pipe in your wall.[6]
    • The gas pipe should have a threaded valve component attached to it. You will be attaching your pipe connector to the valve component.
    • If you have older gas fixtures in your home, you may wish to replace the old valve with a modern-style ball valve designed for use with gas. If you choose to do this, you will have to shut off the gas at the main service valve first.[7]
    • You will probably need an adapter to attach the connection pipe to the valve.
  5. Use a pair of adjustable wrenches to tighten the connections between all the gas line components. Take care not to over-tighten and torque the pipes or strip the threads.
  6. Make a solution of one part water and one part mild dish detergent. Spread a thin coating on the connectors between the various gas pipe components. Then, switch on the gas at the dryer supply valve. If you see bubbles forming on the connectors, this means there are leaks in your gas line.[8]
    • If you do see leaks, turn off the gas, carefully tighten your connections, and try again.
    • To be extra certain that there are no leaks, you can rent a gas leak detector from your local hardware store.
    • Never attempt to test for gas leaks with an open flame!
  7. Shut the gas off again at the dryer supply valve. Leave the gas off until the full installation is complete.
  8. Advertisement
Part 3
Part 3 of 4:

Attaching the Exhaust Vent

PDF download Download Article
  1. You'll need a venting system, but you'll have to choose between two types. There is rigid venting, which comprises a hard metal tube that works for distances no greater than 40 feet (12.2 m). There is also semi-rigid venting, which uses a flexible hose that works for no more than 20 feet (6.1 m).
    • In general, rigid venting is best for dryer vents that are installed at floor level.
    • If you need to attach your dryer to a vent above floor level, you may need a semi-rigid vent hose. Or, if you use a rigid vent hose, you can attach a pair of elbow-shaped bends to the top (where the hose connects to the wall) and the bottom (where the hose connects to the dryer).
    • Dryer vent hoses should be 4 inches (10.16 cm) in diameter.
    • Use a metal vent hose rather than plastic or vinyl, as these are a fire hazard.
  2. Make sure the connections at both ends of the vent hose are secure. You can do this with hose clamps, duct tape, or foil tape. However, hose clamps are the most secure option, as tape can eventually dry out and lose its adhesive properties.[9]
  3. Make sure that it is clear of lint and other blockages, and that the vent hood is still in place. Carefully clean out any buildup.
  4. Advertisement
Part 4
Part 4 of 4:

Finishing the Installation

PDF download Download Article
  1. If your dryer does not come with a cord, buy a power cord which is suitable for the dryer you have purchased. You will also need a strain relief to keep the cord from becoming damaged.
    • The appropriate cord and strain relief type should be listed in the manufacturer's manual.
    • Install the strain relief at the power cord through-hole.
    • Open the terminal block access cover and attach the ends of the power cord to the appropriate terminals.
    • Tightly secure the ends of the power cord and the strain relief with the screws, and then replace the terminal cover.
  2. It should be several inches away from the wall. It should also not be located in an area that is overly cold, as this can inhibit the dryer's function.
    • If you are using a flexible or semi-rigid exhaust vent hose, take extra care not to crush the hose between the dryer and the wall.
  3. Keeping your dryer level will ensure that it is stable. Get a basic level and check it side to side and front to back, at all four corners, and at the center. If necessary, adjust the lengths of the legs on the dryer to make it completely level.[10]
  4. You should now be ready to use your new dryer.
  5. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    Why should I shut off the breaker?
    Mark Spelman
    Mark Spelman
    Construction Professional
    Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.
    Mark Spelman
    Construction Professional
    Expert Answer
    This is not necessary unless you are installing a new power outlet, or moving one.
  • Question
    Is it best to call a plumber to install a gas dryer?
    Mark Spelman
    Mark Spelman
    Construction Professional
    Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.
    Mark Spelman
    Construction Professional
    Expert Answer
    Yes. If you are not comfortable installing the dryer yourself, call a plumber.
  • Question
    Who do I call to install a gas dryer?
    Mark Spelman
    Mark Spelman
    Construction Professional
    Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.
    Mark Spelman
    Construction Professional
    Expert Answer
    Call a plumber.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Tips

  • Keep the vent hose as short as possible. This will help dry your clothes quickly.
  • The main gas service shutoff valve is usually located in the front or side of the house. However, it may be located in a cabinet enclosure that is built into or located inside the house.
  • Unlike electric dryers, gas dryers use standard plugs. Additional extensions are not required to use a gas dryer.
Show More Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

You Might Also Like

Advertisement

About This Article

Mark Spelman
Co-authored by:
Construction Professional
This article was co-authored by Mark Spelman. Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987. This article has been viewed 566,142 times.
6 votes - 53%
Co-authors: 17
Updated: August 6, 2022
Views: 566,142
Article SummaryX

Before installing a gas dryer, make sure your home can support one. To do this, first check the voltage on the dryer. Most modern gas dryers use 120 volts, so look at your circuit breaker and make sure you have 2 columns of 120-volt circuits. You’ll also need an exhaust vent in your laundry room that matches the one on your dryer. If they don’t match, check for a vent adapter or transition pipe at your hardware or home supply store. Finally, make sure there is a gas line installed in your laundry room. Ideally, the supply valve should be within about 6 feet (1.8 m) of where you plan to install the dryer. When you’re ready to connect the gas supply to the dryer, switch off the breakers that supply power to the laundry room, and turn off the gas supply using the valve in the laundry room. You can also shut off the gas at the main supply valve for your home. Put a little threading compound on the end of the dryer’s gas pipe, and apply some to the threaded end of the laundry room gas hookup, too. This will help create a better seal and prevent gas leaks. Use a flexible pipe connector with stainless steel fittings to connect the gas pipe on the dryer to the gas hookup. Then, use a pair of adjustable wrenches to tighten the connections between all the gas line components. To make sure there are no leaks in your hookup, coat the connectors between the components with a mixture of 1 part water and 1 part mild dish soap. Then, switch on the gas. If you notice bubbles forming on any of the connections, tighten them and try again. Turn the gas back off before moving on to the next part of the installation. Next, connect the exhaust vent on the dryer to the vent in your wall with a vent hose. If possible, use a rigid metal vent hose instead of a plastic or vinyl one to reduce the risk of fires. Secure the vent in place at both ends with hose clamps. Then, check the outside duct opening on your exhaust vent to make sure it’s clean, clear of debris, and still has a vent hood attached. To finish up the installation, plug in the dryer’s power cord and move the dryer into its final position. Use a level to make sure the dryer is sitting nice and flat, which will help keep it stable and working correctly. Switch the breakers and gas back on, and you are ready to use your new gas dryer. For tips from our Home Improvement reviewer on how to use dish soap to test for gas leaks in the pipe connections, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 566,142 times.

Reader Success Stories

  • Amy Thompson

    Amy Thompson

    Jan 30, 2017

    "Everything was very useful. I have never hooked up a gas dryer and have never worked with gas so I read everything...." more
Share your story

Did this article help you?

Advertisement