The Complete DIY Guide to Installing a New Faucet in Your Kitchen

You don’t need to call a plumber to install a brand-new faucet in your kitchen. With an adjustable wrench, the new faucet, and some Teflon tape, you can remove the old faucet and set up the new one all by yourself. Depending on the type of faucet you buy and the number of holes in your sink, the process might vary, but with these step-by-step instructions, your kitchen faucet can be up and ready to go in no time.

Things You Should Know

Shut off the hot and cold water supply valves, then use a wrench to disconnect the supply lines connected to them.
Remove the nuts from the old faucet, pull it out, and clean any grime below it. Assemble the new faucet and cover any excess holes with an escutcheon plate.
Feed the supply tubes into the faucet hole and position the new faucet, then tighten the nuts underneath. Attach the new water supply line hoses to the hot and cold valves.

Part 1

Part 1 of 4:

Disconnecting the Water Supply Lines

Download Article

1
Shut off the hot and cold water supply valves under the sink. Open the cabinets under your sink and find the knobs that control the water valves attached to your pipes. Turn the knobs so they’re perpendicular to the pipes to close them. If you don’t have water valves under your sink, turn off the main water line.^{[1]
X
Research source}
- If you have a garbage disposal under your sink, unplug it. If you have an electrical outlet below your sink, turn off the breaker that connects to it before you remove the old faucet.
- If you have difficulty turning the valves, use a rag or pair of pliers to improve your grip.
- Clear out all supplies and products under the sink.^{[2]
  X
  Research source}
2
Turn on your faucet to relieve any water pressure. After turning off the hot and cold water supply valves, lift or turn the handles to your existing faucet to relieve any pressure in the lines and clear out any water that might be trapped in the pipes.^{[3]
X
Research source}
- Keep a shallow bowl or pan and a couple of old towels nearby to catch water while you’re working.
Advertisement
3
Disconnect the supply lines that run from the faucet to the hot and cold valves. The supply lines are hoses connected to the hot and cold pipes with hexagonal nuts. Use an adjustable wrench to unscrew the nuts from the hoses until you can detach them completely.^{[4]
X
Research source}
- Keep one hand on the water pipe as you loosen the supply lines to make sure you don’t damage any connections behind the cabinet.^{[5]
  X
  Research source}
- Home improvement specialist Allen Lee says that if the “angle stops that turn the water on and off” are leaking and haven’t been touched in years, “you're going to want to definitely have that looked at by someone who's trained in that and knows how to replace angle stops if that is needed.”^{[6]
  X
  Expert Source
  
  Allen Lee
  Home Improvement Specialist
  
  Expert Interview. 10 June 2020.}

Part 2

Part 2 of 4:

Removing the Old Faucet

Download Article

1
Use a basin wrench to remove the nuts from the faucet. Adjust the length of the wrench handle and place the jaws of the wrench around the nuts connecting your faucet to the hose. Turn the wrench counterclockwise to loosen the nut completely.^{[7]
X
Research source} If you have a sprayer, use the wrench to take off the nut connecting the diverter to the sprayer hose, too.
- A basin wrench is a long-handled tool that can make it easier to reach underneath your sink.
- A single-handle faucet will typically be connected to a single shank that contains the hot and cold supply lines. A 2-handle center-set faucet will have the mounts on both supply lines.
- If any nuts or mounting hardware is rusted or difficult to remove, apply a penetrating oil to loosen it. You may have to apply it multiple times before you can get the nut off.^{[8]
  X
  Research source}
Tip: Have someone help you hold the faucet from above so it doesn’t spin while you loosen the nut.
2
Pull the faucet out of the sink and clean any grime or residue. Once you remove the nuts and mounting hardware, simply pull the faucet up and out of the holes in the top of your sink. Use a multipurpose cleaner and a cloth to clean any grime that may have developed around the old faucet.^{[9]
X
Research source}
- You may have to apply pressure to break the caulk seal.
- You can also scrape off any caulk or plumber’s putty with a putty knife—just be careful not to scratch the sink or countertop.^{[10]
  X
  Research source}
- If you’re having trouble removing any grime, let the cleaner sit on it for 1 minute before trying to scrub it off again.

Part 3

Part 3 of 4:

Installing the New Faucet

Download Article

1
Buy a faucet that fits the number of holes in your sink. The number and placement of the holes can limit the kind of faucet you can install.^{[11]
X
Research source} However, some setups, like a wide set faucet where the handles and faucet and separate individual units, can be installed with any number of sink holes.
- If you have 3 holes in your sink, measure between the center of the first hole and the center of the second hole. This is called the “spread,” which determines what size faucet you can install.
- A single-handle center-set faucet can be mounted directly in 1 hole, or you can buy an escutcheon plate to cover up the 2 outside holes in a 3 hole sink.^{[12]
  X
  Research source}
- A 2-handle centerset faucet has separate hot and cold handles that are connected to the base and fit cleanly into 3-holed sinks.
Tip: If you have additional holes left in your sink, you can use them for a built-in soap dispenser or a sink sprayer. If you’d like a sprayer but don’t have enough holes, you can buy a pull-out sprayer that stretches out from the spout of the faucet.
2
Assemble the faucet and cover any extra holes with an escutcheon plate. Follow the manufacturer’s instructions for the proper assembly of your specific sink faucet. If you’re not using some of the holes at the top of your sink, use the included escutcheon (or deck) plate or buy a separate one to cover them.^{[13]
X
Research source}
- Wrap 3 layers of Teflon tape around the threading of the supply tubes that came with your faucet, then screw the supply tubes onto the faucet fixture using an adjustable wrench.
- Most escutcheon plates included with sink faucets also have a rubber gasket that attaches underneath the plate to seal the holes at the top of your sink.
  - If the base of your faucet doesn’t come with a rubber gasket, apply a bead of silicone caulk or plumber’s putty to the faucet base.^{[14]
    X
    Research source}
Align the faucet over the center hole at the top of your sink and feed the tubes through one at a time so they’re easier to manage. After the tubes are in, lower the faucet onto the sink and hold it in the position where you want to secure it.^{[15]
X
Research source}
4
Secure the faucet by tightening the nuts with your basin wrench. Have a helper hold the faucet from above the sink so it doesn’t shift or move around. Screw the nut with your fingers until it almost hits the underside of the sink, then tighten down the mounting screws evenly until the faucet is tight against the underside of the sink.^{[16]
X
Research source}
- If your faucet assembly doesn’t have mounting screws, simply use a basin wrench to screw on the nut until it’s tight against the underside of the sink.
- Try to avoid over-tightening the nuts.
Set the sprayer base in one of the holes in your sink and screw on the mounting nut to secure it in place. Feed the sprayer hose through the base and attach the end of the hose to the bottom port on your faucet.^{[17]
X
Research source} Depending on the type of sprayer, you may just have to push the hose in place or screw it together.
6
Attach the water lines to the faucet supply hoses. Hold the supply hoses with the nuts attached to them from the faucet up to the hot and cold water valves. Wrap 3 layers of Teflon tape around the threading of both valves in the same direction as you’d tighten the nuts in.^{[18]
X
Research source} Screw the nuts onto the valves with your fingers and tighten it down with an adjustable wrench.
- Keep one hand on the pipe for the water supply valve running into the wall as you tighten the valves so you don’t damage any connections.
- For faucets with 2 handles, make sure the hot water line is connected to the side that controls hot water, and the cold water line is attached to the cold handle.
- If you had to disconnect a garbage disposal earlier, plug it back in.

Part 4

Part 4 of 4:

Cleaning out Debris & Checking for Leaks

Download Article

1
Turn the water on and check for leaks under the sink. Turn on the hot and cold water valves under the sink and test out your faucet and sprayer. With the water running from the tap, check if there are any leaks in any of your faucet connections. If you find a leak, use an adjustable wrench to tighten the connections until it stops.^{[19]
X
Research source}
- Keep a towel or bucket underneath your valves until you’re sure they don’t leak anymore.
2
Unscrew the aerator from the end of the faucet to flush out debris. The aerator is a small layer of metal mesh used to control the water flow. Twist the aerator counterclockwise to remove it from the end of your faucet.^{[20]
X
Research source}
- Check the instruction manual for your faucet to see how to remove it from your exact model.
3
Turn on your faucet and let the water run for 1-3 minutes. Lift or turn the handles on your faucet so the water runs out. Keep the faucet on for a few minutes so any debris or dust inside is flushed out of the water lines.^{[21]
X
Research source}
- If your faucet has 2 handles, turn both of them on to clear out all of the lines.
- Afterward, turn off your faucet and screw the aerator back on. Now you can use your new faucet!^{[22]
  X
  Research source}
Tip: Check underneath your sink again while the water is running to see if you notice any leaks. If so, tighten the nuts on the water lines.

Expert Q&A

Search

Add New Question

Question

Do I have to install a kitchen faucet myself?

Allen Lee
Home Improvement Specialist
Allen Lee is a Home Improvement Specialist and the Owner of Honest Lee Handyman Services, a licensed and insured handyman business servicing Sacramento, California, and surrounding areas. Working with homeowners and businesses to get their small repairs done in a timely and efficient manner, Honest Lee Handyman Services provides gutter and dryer vent cleaning along with fixture, fence, drywall, and toilet repairs.

Allen Lee

Home Improvement Specialist

Expert Answer

If you don’t feel comfortable replacing a faucet or are confused by any of the pipes under your sink, contact a plumber to come do the job for you.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 0 Helpful 2
Question

What do I do if my angle stops are leaking?

Allen Lee
Home Improvement Specialist
Allen Lee is a Home Improvement Specialist and the Owner of Honest Lee Handyman Services, a licensed and insured handyman business servicing Sacramento, California, and surrounding areas. Working with homeowners and businesses to get their small repairs done in a timely and efficient manner, Honest Lee Handyman Services provides gutter and dryer vent cleaning along with fixture, fence, drywall, and toilet repairs.

Allen Lee

Home Improvement Specialist

Expert Answer

Unfortunately, this is a common issue with older valves. I suggest you hire a professional to replace the angle stops before you continue doing any work.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 0 Helpful 0

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

If you have a wall-mounted faucet or you need to remove additional plumbing to access the old faucet, you might have to call a professional plumber to do the job instead.^{[23]
X
Research source}

Thanks
Helpful 0 Not Helpful 0
If you don’t have hot and cold water valves under your kitchen sink, consider installing them so you can turn off the water easily in the future.

Thanks
Helpful 0 Not Helpful 0
Place a pillow at the edge of the cabinet to lean on while you’re working underneath the sink.

Thanks
Helpful 0 Not Helpful 0

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Try to avoid over-tightening the nuts on the bottom of your sink because it could damage your sink or cause leaks.

Thanks
Helpful 0 Not Helpful 0
Wear safety glasses to prevent dirt and debris from falling into your eyes while you work under the sink.^{[24]
X
Research source}

Thanks
Helpful 0 Not Helpful 0