How to Jam a Network

Download Article

Co-authored by Luigi Oppido

Last Updated: April 11, 2024 Fact Checked

Download Article

Using a Jammer

|

Preventing Interference

|

Q&A

|

Tips

|

Warnings

To jam a network, you need to broadcast radio signals on the same frequency, overpowering the original signal. Jamming devices that broadcast on a wide range of frequencies at once can disrupt everything from police radar to GPS systems, and are illegal in many countries. You can use your own WiFi router instead, or another wireless device that broadcasts on a more narrow range of frequencies. Better yet, adjust your own setup to avoid interference and save your relationship with the neighbors.

Method 1

Method 1 of 2:

Using a Jammer

Download Article

1
Use a jamming device if legal in your area. Using a jamming device is illegal in many countries, including the United States.^{[1]
X
Trustworthy Source

Federal Communications Commission
Independent U.S. government agency responsible for regulating radio, television, and satellite, and phone communications

Go to source} If it is legal in your area, all you need to do is buy one and turn it on close to the source of the network. However, in most areas, you will need to resort to the more complex, legal methods below. Alternatively skip to the section below instead for legal ways to prevent neighbors from using your signal, and reduce nearby signals' effect on your own network.
- Jamming can interfere with emergency radio communications and other vital communications. Even if it is legal in your area, it's best not to use a jamming device in a densely populated area.^{[2]
  X
  Expert Source
  
  Luigi Oppido
  Computer & Tech Specialist
  
  Expert Interview. 30 September 2021.}
- Don't assume jamming devices are legal just because someone in your area is selling them. These merchants may be breaking the law.
2
Identify the frequency you want to jam. Assuming jamming devices are illegal in your area, you'll need to use a more targeted method. Each wireless device sends signals on one or more frequencies. To drown this signal out, you'll need to operate on the same one. Look up the name of the device you're trying to jam, or use this guide to Wi-Fi frequencies:
- Wi-Fi routers that follow the 802.11b or 802.11g standards operate at a frequency of 2.4GHz. This is a safe bet if you can't identify the router.
- Wi-Fi routers with the 802.11a standard operate at 5GHz.
- The 802.11n standard can operate at either 2.4 or 5GHz. You may need to jam both frequencies. Some modern routers with this standard can alter their frequency automatically, which will make it much harder to jam.^{[3]
  X
  Research source}
- If you don't know the type of router being used, try downloading a program or app for viewing nearby wireless networks. Some of these will identify the frequency and channel being used, but the free versions usually do not.
Advertisement
3
Turn on a device at the same frequency. You can block a 2.4GHz wireless signal by operating a microwave, an older cordless phone, a Bluetooth device, and many other wireless devices. As long as it's labeled 2.4GHz, it should interfere with a nearby 2.4GHz network. The effect can vary between a slight slowdown and a complete shutoff, but unfortunately there's no way to tell in advance which it will be.
- The device must be broadcasting a signal. For instance, play music into a phone, or tape down the number buttons so they're being pressed continually.
- Do not run a microwave with nothing inside.
- To improve the jamming ability of a 2.4GHz cordless phone, expose the circuitry, then attach the antenna leads to a wire taped to a CD.^{[4]
  X
  Research source} This may violate laws where jamming is illegal.
4
Alter your router for more control over jamming. If your Wi-Fi router operates on the same frequency, you can fine tune its settings to cause intentional interference.^{[5]
X
Expert Source

Luigi Oppido
Computer & Tech Specialist

Expert Interview. 30 September 2021.} Start by accessing your router's settings. To do this, open an internet browser and enter the address of your router in the URL bar. Try the following common options, until you see a page of router options:
- http://192.168.0.1
- http://192.168.1.1
- http://192.168.2.1
- http://192.168.11.1
- If none of these work, search for your router model's IP address online, or try to find it listed in the Network or WiFi settings of your computer or mobile device.^{[6]
  X
  Research source}
- You may need to log in before you can view the settings. Refer to your router manual if you do not know the password.
5
Select the transmission channel. A router does not use its entire range of possible frequencies at once. Instead, the range is divided into 14 channels in the 2.4GHz range, and 23 channels in the 5GHz range.^{[7]
X
Research source} Depending on your router, you may not have access to all these channels, or you may have limited ability to change this setting. Do your best to use as many channels as possible.^{[8]
X
Expert Source

Luigi Oppido
Computer & Tech Specialist

Expert Interview. 30 September 2021.} If you can only use one or two channels at a time, switch between each channel and test whether the nearby network's signal strength has dropped.
- At 2.4GHz, most routers operate on the 1, 6, and 11 channels. Use these channels as well to interfere with the other network.
- Nearby channels overlap with each other, causing some interference. Using channels 3, 7, and 11 will slow down almost any nearby Wi-Fi network, at least a little.
- At 5GHz, there are many more channels available.
6
Change other settings. There's no standard settings menu for all routers. You may not have access to all these settings, or your router may use different names. Look at your router's documentation for more information. If you do see any of the following settings, make these changes:^{[9]
X
Research source}
- Set "Channel Width" or "Bandwidth" to the largest possible range.
- Disable automatic channel selection.
- Boost power output to maximum.

<span="prevent">

Method 2

Method 2 of 2:

Preventing Interference

Download Article

1
Position physical barriers. Walls and other objects will significantly reduce the range and strength of a Wi-Fi signal. Metal objects, containers of water, and other conductive objects have an especially strong effect. Positioning these in front of thin walls and windows can make it harder for a neighbor to steal your signal. This can also block incoming signals that interfere with your own device.
- 5Ghz Wi-Fi signals are particularly bad at penetrating objects.
2
Reduce your router's power level. Most high-quality Wi-Fi routers have an adjustable power level setting. Turn this down to reduce the strength of the signal. You may need to experiment to find a setting that keeps your Wi-Fi at a suitable strength throughout your home.
- If your kids are sneaking online when they're supposed to be sleeping, consider turning the power level down to minimum each night. Increase it again in the morning.
3
Install a directional antenna. Replace your router's antenna with a directional antenna if you only need to broadcast the signal to one spot, such as your desktop computer or living room. This will significantly weaken the signal everywhere the antenna isn't pointing.
- To save some money, make your current antenna "directional" by placing a sheet of aluminum foil in any direction you don't want the signal to travel.
4
Alter your router channels. Access your router settings through an internet browser, then change the channel setting to avoid interference with other networks.^{[10]
X
Expert Source

Luigi Oppido
Computer & Tech Specialist

Expert Interview. 30 September 2021.} Test channels 1, 6, and 11, testing the Wi-Fi signal strength around your home at each setting. One of these will usually provide a fast, low-interference network.
- If your router allows access to channels 12 or higher, test the highest channel.
- Many modern routers have the option to automatically detect low-interference channels and switch between them. Enable this option if available.
- Each router manufacturer arranges its own settings. If you can't find a channel option, refer to the router manual for a guide.
5
Improve Wi-Fi security. Change your router password if you suspect a neighbor is connecting to your network. This option is available in your router settings, through your browser.
- Select WPA encryption, which is more difficult to hack than WEP.

Community Q&A

Search

Add New Question

Question

Is it possible to jam any communication signals?

Community Answer

Yes, it's possible, but FCC regulations prohibit such jamming without the right license.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 7 Helpful 30
Question

How do I know if somebody is jamming my frequency?

Community Answer

Check the connected devices panel in your router.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 40 Helpful 41
Question

How do I stop a neighbor from using a scanner to access my garage opener frequencies to open my garage door?

Aasim

Top Answerer

Use a rolling code garage door opener. These are available at many garage door stores. A rolling code uses one-time codes that can only be learned by using the "learn" button.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 6 Helpful 14

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Common jamming devices have an operating range of 9 meters (29.5 ft). If the network you want to jam covers a larger area, the jamming device will create a 9-meter blind spot within the network.

Thanks
Helpful 0 Not Helpful 0
If you're trying to block a neighbor's Wi-Fi signal with your own, this will slow down your own network as well. To increase your own network speeds, change your Wi-Fi settings according to the opposite of the advice above.

Thanks
Helpful 0 Not Helpful 0

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

In the United States, it is a federal crime to sell or use a jamming device, except for use by the government. Jamming devices are illegal in many other countries as well.

Thanks
Helpful 4 Not Helpful 0
Jamming another person's network is a rude and unproductive tactic, even if you use legal methods. It's more effective to avoid interference instead, which you can accomplish with the above information on Wi-Fi channels.

Thanks
Helpful 3 Not Helpful 3