PDF download Download Article
An easy-to-follow guide for creating homemade speakers
PDF download Download Article

Speakers produce sound by converting electrical energy into sound energy using magnets to "push" air using the cone of the speaker to push the air in and out at a certain frequency. While entire books have been devoted to this phenomenon, you only need a rudimentary knowledge of sound design to make your own simple speakers. Whether you want to spend weeks developing the next great sound system or just want to understand speakers a little better, read on to learn how to make your own speakers.

Method 1
Method 1 of 2:

Building a Basic Speaker

PDF download Download Article
  1. While there is a lot of calibrating that goes into high end speakers, the basic technology is actually pretty simple. An electrical current is run through a wire that is attached to a magnet. This current makes the magnet vibrate, and those vibrations are picked up by our ears as sound.[1]
    • To hear the sound well you should also get a small plastic tupperware or cup. This will amplify the sound much like yelling into a cone amplifies your voice.
  2. You want to wrap the wire 6-7 times starting from the middle. Make sure you leave several feet of wire unwrapped on either side of the magnet. Tape this coil onto the bottom of your tupperware, but without the magnet.[2]
    Advertisement
  3. Using both ends of the leftover copper wire, make an even large coil and tape this on top of the smaller one. Like before, you will leave roughly a foot of leftover wire on each side of the coil -- this is how you will attach your "speaker" to your music source.
  4. You want it to sit comfortable within both coils, but don't worry too much about touching every inch of wire.
  5. The most common attachment is an 1/8th inch cable or "Auxiliary" cord (the input on most headphones). Wrap one end of the wire around the top of the metal input and the other around the bottom.
    • Gator clips, which are small clamps that transmit electricity, can make attaching your copper wire to a music source easier.
  6. Try using a stronger magnet, keeping your coils tighter, using different "amplifiers," and playing different music sources at different volumes.[3]
  7. Advertisement
Method 2
Method 2 of 2:

Building High-End Speakers

PDF download Download Article
  1. While the basics of speaker technology have not really changed since 1924,[4] audio technicians have been perfecting the design, electronics, and sound of speakers ever since. That said, all speakers contain a few basic components:
    • Driver: Transforms an electrical signal into sound. Drivers come in many shapes and sizes, but all share the same function -- they make noise. Many speakers have multiple drivers to handle many frequencies. For example, "woofers" are large drivers that work well for low-frequency sounds like bass, while "tweeters" handle high frequencies.
    • Crossovers: These small relays take complex electrical signals and break them up into smaller parts to send to different drivers, isolating bass, treble, and mid-range frequencies.
    • Cabinet: This is the shell of a speaker where the electronics are housed. In order to eliminate noisy "resonance" or to get greater volume they are produced in a variety of shapes, sizes, and materials.[5]
  2. While you can certainly buy all of the parts separately, it is incredibly difficult to build good speakers without years of studying the principles of sound and electricity. However, the budding DIY speaker enthusiast has another option -- buying pre-designed speaker kits with drivers, crossovers, and cabinets included. When searching for a good speaker kit, you should consider:
    • Is the cabinet included? Many speaker kits only contain blueprints for the cabinet -- you will have to buy, cut, and fasten the wood together yourself.
    • Is the crossover pre-connected? Depending on your comfort level with electronics, you may want to purchase a kit where the crossover is already assembled, or you can attach and solder the pieces yourself.
    • How high-quality to you want your sound? Most audio professionals consult the Loudspeaker Design Cookbook or LDSB, for advice on choosing drivers and crossovers, and you can expect to pay more for better quality components.
    • How powerful, or loud, do your speakers need to be. In general, this is determined by the size of you drivers.[6]
  3. Solder the crossover together following the provided crossover pattern. You will need a soldering iron, hot glue, and a pattern to make sure your crossover works correctly. All speaker kits come with a chart illustrating how to attach everything, and sample patterns can be found with a quick internet search if you are working from scratch. This prevents your speakers from shorting or burning out.
    • Make sure you completely understand how to read wiring diagrams before continuing.
    • Once your parts are attached, secure them to a small board with a hot glue gun or zip ties.
    • Finish by attaching your crossover cables to the drivers with speaker wire.
  4. If your cabinet is not provided for you, you will need to buy the wood and cut it to fit your drivers. Most speakers are rectangular, but talented carpenters can play with other shapes, from polygons to spheres, to get better sound. While all cabinets are different, there are a few guiding principles to their design:
    • Use material that is at least 1.5" thick.[7]
    • Always measure your wood so that it fits together perfectly -- any sound that leaks out of the speakers will greatly diminish their quality. Fit the speakers together before adhering them.
    • Wood glue is the preferred adhesive, but you can also use a drill and screws or biscuit clips as well.
    • The paint or stain you chose for your cabinet will not affect the sound, but decorate your cabinet before installing components to protect your electronics.[8]
    • Be sure you are comfortable with carpentry equipment before building original speaker cabinets.
  5. If you followed your blueprints correctly the drivers should fit snugly into the holes you cut on the front of the cabinet. Adhere the crossover board to the cabinet so that the cables to the driver are not stretched or stressed.
    • The drivers are usually screwed into a plastic molding on the outside of the cabinet.
    • Use wood glue or adhesive to securely fasten the crossover to the cabinet.
  6. This specially designed fabric is meant to dampen sound inside the speaker so that you don't hear weird vibrations or echos. While not necessary, it can help the sound considerably.
  7. Advertisement


Community Q&A

Search
Add New Question
  • Question
    What is the resistance of a basic speaker?
    Community Answer
    Community Answer
    There is no standard resistance. Most speakers are either 4, 8 or 16 ohms resistance.
  • Question
    Can I take any magnet?
    Community Answer
    Community Answer
    Round magnets will be the best to use, but you can try to make it work with a different shaped magnet.
  • Question
    What is the channel of the speaker?
    Joe hamel
    Joe hamel
    Community Answer
    A channel is a pair of connections. On a speaker, this refers to a set of positive (+) and negative (-) inputs. On a single voice coil, you will only have one positive and one negative, so you only have one channel. On a dual voice coil speaker, you have two positives and two negatives, so without bridging, you have two channels.
See more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Warnings

Advertisement

Things You'll Need

  • Foam bowl
  • Paper plate
  • Button magnets
  • Paper (a4)
  • Copper wire (can be obtained through old TVs, radios)
  • Super glue or a hot glue gun
  • Scissors
  • Lighter

About This Article

wikiHow is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 33 people, some anonymous, worked to edit and improve it over time. This article has been viewed 524,910 times.
How helpful is this?
Co-authors: 33
Updated: June 3, 2024
Views: 524,910
Categories: Audio Speakers
Article SummaryX

To make your own speakers, you'll need copper wire, packing tape, a strong magnet, and a plastic container. First, wrap the copper wire around the magnet several times to make a coil so there are several feet of wire unwrapped on each side of the magnet. Then, remove the magnet and tape the wire coil to the bottom of the plastic container. Then, make a larger wire coil using a different round object and tape the coil to the top of the first one. Finally, put the magnet on top of the 2 coils and attach the ends of the copper wire to a music source. To learn how to build high-end speakers, scroll down!

Did this summary help you?

Thanks to all authors for creating a page that has been read 524,910 times.

Reader Success Stories

  • Sanjeev Kumar

    Sanjeev Kumar

    Feb 21, 2017

    "This was very helpful article for me because I want to know the technology on a very basic level. In my mind, I..." more
Share your story

Is this article up to date?

Advertisement