PDF download Download Article PDF download Download Article

Wind chimes, a decorative piece that can liven up your home, can be made from a variety of materials such as ceramic pieces and metal tubing. If you are going for a natural look and mellow tone, bamboo is an excellent material to use. You can make a simple project out of creating your own bamboo wind chime by following the steps below.

Method 1
Method 1 of 1:

Making a Bamboo Wind Chime

PDF download Download Article
  1. If you are lucky, bamboo may already be growing wild in your area, and it is simply a matter of obtaining permission and cutting the bamboo plant to a proper size. If there is no local source, you may be able to purchase a common bamboo pole, used for fishing. You can also often buy bamboo poles of varying sizes at garden supply stores.
    • Make sure your bamboo is thoroughly seasoned and is not split or rotten.[1]
  2. Each length should be composed of two of the plant's "sections", with one end above the partition-like segment end, and the other below it, so you have an open tube to work with.
    Advertisement
  3. of each piece. This can be done with a very sharp knife, but care must be used, since both the splinters from the bamboo and the knife can impale or cut you. If you have a vice, it might be easier (and less risky) to fix the bamboo in the vice and cut it with a saw, especially if it is quite tough. Taper the last inch (2.5cm) or so off at an angle.[2]
  4. Drill 1/8 inch (3mm) holes just above the section on the solid end of each piece, parallel to the cut you made on the opposite end. This will ensure the hollow, concave bamboo "channel" will be facing out on each tube when they are assembled.[3]
  5. or other material about 7 times the diameter of the average piece of bamboo. In the photos, each piece was about 1 inch in diameter, so the plywood disk is 7 inches (~18cm).
  6. Lay out the disk into 6 equal spaces around the circumference, then drill a 1/8 inch (3mm) hole about 3/4 inch (~2cm) on either side of the layout marks, near the edge of the disk.
  7. The string should be about 48 inches (1.2m) long to begin with; any surplus can be cut off after each tube is tied in place. Heavyweight fishing line can be used for hanging the tubes, as in the photos, but a more flexible string will give better results.
  8. Thread your string through the holes in the end of one bamboo section, then back through the hole in the plywood on the other side of your layout mark. Continue doing this until each bamboo is hanging under the plywood disk, then tie off the end of your line.
  9. so that each one is staggered higher or lower than the adjacent one. This is what changes the tone of each bamboo, so you can experiment here until you obtain a pleasant sound with the tonal variation you desire.
  10. Measure and cut three equal lengths of string, about 30 inches (0.75m) long, and tie them together on one end, allowing a small loop to be formed.
  11. in the plywood, snug them slightly, and while holding the disk level, drop some hot-melt glue on each to secure it in place.
  12. Drill three 1/8 inch (3mm) holes spaced equally about the center of this disk, about 3/4 to 1 inch (1.9 to 2.5 cm) from the center. Thread the loose ends of your three center strings through these holes, allowing it to hang about 1/4 of the distance down from the top of the bamboo sticks.
  13. , using hot-melt glue again, keeping this smaller disk level also. This disk will be the "hammer", the striker that produces the sound of your chimes.
  14. Cut a shape of plywood or other material to hang below the hammer, or lower disk, and tie it on the end of your three strings. This will catch the wind, causing the hammer to strike the bamboo tubes as the wind makes it sway back and forth. One with a larger area will move more in a lighter breeze. Feel free to experiment with different materials in different sizes and weights.
  15. Secure any loose ends of strings, gluing everything with an extra bit of hot-melt glue so nothing comes untied while your chime blows in the breeze. Sand and varnish, or paint your chimes if you like.
  16. Advertisement

Community Q&A

Search
Add New Question
  • Question
    Does the bamboo have to be dried first or can I do this when its still green?
    Community Answer
    Community Answer
    Either way is fine. You can start with green bamboo and it will dry after it's been hanging for a few days. Whichever way you prefer working with the bamboo should guide your choice.
  • Question
    Why do I have to split the end of the bamboo?
    Community Answer
    Community Answer
    When the bamboo knock together, the wind gets carried up throughout the stick and it makes the music or melody louder.
  • Question
    How do I tune each piece of the bamboo?
    Community Answer
    Community Answer
    Cutting the bamboo shorter makes it a higher pitch, while cutting it longer makes a lower pitch. Bamboo chimes work when wind makes the bamboo sticks hit against each other, creating sound. You can test the bamboo sticks by hitting them.
See more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

  • Cutting different diameter tubes, or different lengths, will produce different sounds. Generally speaking, larger tubes produce deeper tones.
  • Similar steps can be used with any hollow material, such as PVC tubing or metal pipe.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Warnings

  • Some neighbors really, really, do not like the sound of wind chimes. Be considerate where the wind chime is placed.
  • Sharp knives are used in this project, and can harm you. Be sure to use carefully.
  • Splinters from bamboo pieces may hurt or impale you as well.[4] Take caution when cutting, and use protection for your eyes and hands, such as safety goggles and gloves, if necessary.
Advertisement

Things You'll Need

  • Bamboo
  • 1/4 inch (.6cm) thick plywood, about 2 square feet (30.5 sq cm) in length
  • String
  • Drill and saw
  • Hot-melt glue gun and glue
  • Optional - Paint or stain sealant for the plywood disk(s)

Expert Interview

Thanks for reading our article! If you’d like to learn more about hobbies and crafts, check out our in-depth interview with Diane Henkler.

About This Article

Diane Henkler
Co-authored by:
Crafting and Home DIY Specialist
This article was co-authored by Diane Henkler. Diane Henkler is a Crafting and Home DIY Specialist based in Lexington, South Carolina. She is the owner and creator of InMyOwnStyle.com, a crafting, DIY, and home design blog. She started her blog in 2009, and has now been blogging about affordable decorating, creative DIYs, and lifestyle tips for 15 years. Her career background was in retail display curation, which led her into the world of DIY decorating and home design. In her blog, she features pieces on decorating inspiration, seasonal holiday decor projects, organization strategies, room makeover guides, painting tutorials, furniture restoration tips, and more. Diane’s blog demonstrates how decorating a home does not have to be hard, expensive or time consuming. Through her posts, she shares decorating advice, ideas, project how-to’s, and more, furthering her mission to help her readers create beautiful homes, especially on a budget. She also creates tutorials and educates followers on her social media crafting channels. This article has been viewed 410,073 times.
How helpful is this?
Co-authors: 28
Updated: November 19, 2024
Views: 410,073
Article SummaryX

A bamboo wind chime is a unique piece that can liven up your decor. To make one, first, you’ll need to cut bamboo into 6 pieces for the chimes. Each piece should be a slightly different length so it will make a different sound. Then, you’ll need to use a sharp knife to carefully split and hollow each piece. Once they’re hollow, you’ll need to drill a hole at the top of each section and secure them to a piece of plywood with thread. Make sure the string is loose enough that they can move around in the wind. Finally, cut a disk out of plywood and hang it in the middle of the bamboo pieces. If there are any loose pieces on your wind chime, use a little hot glue to secure them. To learn how to make a hanging mechanism for your wind chime, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 410,073 times.

Reader Success Stories

  • Julie Lowe

    Julie Lowe

    Oct 21, 2020

    "My sister collected lots of large diameter bamboo in Louisiana for me. I wanted to make a wind chime for each of us..." more
Share your story

Did this article help you?

Advertisement