How to Make a Biscuit Joint

Co-authored by Matt Mimnagh

Last Updated: April 30, 2024

Biscuit joints are a method for gluing boards together along their edges to create a wider slab or plank without screwing or splicing them. This technique is used for making tabletops, furniture, and cabinets, and although it requires special tools, it is within the reach of most hobby woodworkers in a home woodshop.

1

Prepare your materials.

Download Article

Gather the tools and materials you will need for the project. It is very helpful to have a good, flat, sturdy workbench for this woodworking operation. Briefly, you will need at least the following:
- A plate jointer, also known as a biscuit jointer.
- A saw.
- Measuring tape.
- Square.
- Wood glue/ Carpenter's glue.
- Clamps.
- Lumber.

2

Select lumber of similar thickness.

Download Article

You can laminate lumber together of differing thicknesses if only one side will be visible, or if you have access to a power plane, but ideally, you will begin with sized, square material of the same thickness.

3

Edge and size the boards.

Download Article

If a beaded look is desired, a rounded edge common in nominal lumber is acceptable, as seen in the scrap material used for the illustrations.

4

Mark the location of the biscuits to be glued between the boards.

Download Article

Generally, the distance between biscuits will determine how strong the finished plank will be, and thinner lumber will hold better if the spacing is kept to a minimum. One inch nominal lumber joins fairly well at a twelve inch biscuit spacing, two inch lumber can be cut at sixteen to eighteen inches on center with good results.

5

Set the cutting depth of the plate jointer.

Download Article

For single row biscuits, you will want to place the joints at the center of the board's edge, for double rows, cut each row at one third of the boards thickness.

6

Cut the biscuit slots with the plate jointer.

Download Article

7

Clean the biscuit slots.

Download Article

8

Apply your glue.

Download Article

Fill the slot about one fourth full of a good quality wood glue. Press the precut biscuits into the slot, and notice if excess glue runs over its edges. This excess can end up on the finished surface of your work, making it almost impossible to stain uniformly later if you desire to do so.
- Spread a small amount of glue along the edge of the board you are mating to the one you have inserted the biscuits into. Fill the respective biscuit slots one fourth full as you go.

9

Align your boards.

Download Article

Then clamp them tightly and allow the glue to dry.

10

Finish.

Download Article

Expert Q&A

Search

Add New Question

Question

How strong are biscuit joints?

Matt Mimnagh
Master Carpenter
Matt Mimnagh is a Master Carpenter and Owner of Castleguard Home Services based in Charlotte, North Caroline. Castleguard specializes in finish carpentry including the installation of moulding, trim, and built-in cabinetry. They also offer kitchen, bathroom, and other remodeling services.

Matt Mimnagh

Master Carpenter

Expert Answer

Pretty strong! Composite biscuit joints are very thick and can support a man's full body weight (or at least a couple hundred pounds).

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 1 Helpful 2
Question

Can I use a router to make biscuit cuts?

Community Answer

Yes, if you have the correct cutter and make the cut slightly longer than the biscuit.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 11 Helpful 9
Question

Can I join the boards end to end (or in a "T" shape) with biscuits?

Community Answer

Yes, you can. It's always better to use dowels for a T joint, but it can be done.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 12 Helpful 10

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Be sure to have the fence of the biscuit joiner flat to ensure proper fitting of the two joining pieces. Failure to do so will result in an uneven surface of the two pieces of joined wood.

Thanks
Helpful 7 Not Helpful 1
Choose an appropriate sized biscuit for the dimension of the lumber you are using.

Thanks
Helpful 11 Not Helpful 4
Keep biscuits dry, as they can absorb moisture and swell before use.

Thanks
Helpful 7 Not Helpful 2

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Plate jointers have a high speed wood cutting blade which is concealed except during use, so keep fingers away from the cutting head when in use.

Thanks
Helpful 1 Not Helpful 0
Keep your work area clean and make sure it is well lit.

Thanks
Helpful 1 Not Helpful 1
Wear safety glasses when using woodworking power tools.

Thanks
Helpful 0 Not Helpful 1