PDF download Download Article PDF download Download Article

A light bulb is made when metal filament is heated to the point at which the wire glows. The most well-known type of light bulb is the incandescent light bulb, which is the version used in most homes. Use these steps for making a homemade light bulb.

Method 1
Method 1 of 2:

Making a Simple Graphite Light Bulb

PDF download Download Article
  1. Everything here is easy to round up at a local hardware store, if you don't already have it all at home. You'll need.
    • Two strands of copper wire (roughly 1-2 feet, each)
    • One clear glass jar
    • Small glass jar for smaller bulb
    • Five or more batteries
    • Four crocodile snips
  2. You should use the kind you get in mechanical pencils -- the thin, solo pieces of graphite that you can usually buy in packs. The thinner, the better -- try something like .5mm thickness.[1]
    • Pencil lead actually isn't lead at all, it is graphite. Graphite is an electrical conductor, making it a good filament for homemade light bulbs.
    Advertisement
  3. Watermark wikiHow to Make a Light Bulb
    The ends of each wire should have a clip on it. If you don't have clips, you can still make a light-bulb. To do so, curl each end of the wire into a little round hook.
    • If you are making the hooks yourself, make them big enough to fit over the end of the battery.
  4. Watermark wikiHow to Make a Light Bulb
    This simply means you tape them together, end to end, so that they all work together to provide power. Make sure you line them up positive end to negative end. Then use electrical tape to secure all the batteries together into a long rod.
    • Wrap the tape tightly enough around the batteries so that they hold together. You may need to overlap the tape a few times.
    • You must arrange the batteries so that there is a positive node on one end, and negative on the other.
  5. Watermark wikiHow to Make a Light Bulb
    Usually, you'll have a wire with red clips and one with black. Hook one end of the red clips up to the positive end of the batteries, but leave the other clip off for now. If you hook everything up, you'll actually be turning the light bulb on before you're ready. You could get burned if you're not careful
    • You can reverse the red and black if you want-- you just need different wires on each end.
    • Remember you only want to hook up one wire right now.
  6. Watermark wikiHow to Make a Light Bulb
    Think of making an H-shape, where the two clips are the sides and the graphite is the horizontal line in the middle.[2]
    • The longer the graphite, the longer your bulb will last.
    • Use some tape, glue, or modeling clay to help stick the clips face up.
  7. Watermark wikiHow to Make a Light Bulb
    This isn't strictly necessary, as the graphite would still light even without the jar. But the process creates smoke, and the graphite can shatter. Moreover, having an actual "bulb" helps create a more even light.
    • The size of the jar does not matter, but the jar should be clean.
    • If the jar has a label, it would be a good idea to remove it; this will make it easier to see the light.
  8. You are making a simple circuit, connecting the batteries in an electrical loop. The light comes from the graphite -- as electricity flows through it, it heats up and emits energy in the form of light and heat. Thus, your light bulb!
  9. If the light is weak, or isn't working, there are some things you can do to make sure you get a working light.
    • Check the graphite thickness. While larger thicknesses work, 0.5 mm seems to work best.
    • Add a few more batteries. Also, make sure that the ones you have are touching end to end.
    • Make sure the wires are snug and well-connected to the batteries.
  10. Advertisement
Method 2
Method 2 of 2:

Using Iron Filaments

PDF download Download Article
  1. Copper is a great conductor of electricity, and most wiring is copper. You need two strands about 1 ½ feet (45 cm) long.[3]
    • Use small wire cable cutters to cut the copper wire.
  2. Watermark wikiHow to Make a Light Bulb
    The shielding is the rubber that covers the copper wire. Removing it can be achieved by carefully squeezing the cable cutter so that it cuts through the shielding but not the wire. The shielding can then be stripped from the ends with your hands.
    • You need to expose the end of the wire, otherwise you won't be able to complete your circuit.
  3. Watermark wikiHow to Make a Light Bulb
    The holes should be in the middle of the cork about 1/2" apart. This cork will hold your wires in place. Think of it as the bottom, metal part of your light bulb.
    • You can reuse an actual cork from a wine bottle, or you can buy a package of corks from the craft store.
  4. Watermark wikiHow to Make a Light Bulb
    Leave about 2" or so exposed above the top of the cork.
    • If you need to, strip the shielding off of the wire to expose the metal.
  5. The hook of each strand should curve the same way. For example, you can have the hooks both curve to the left, or both curve to the right.
    • This will hold onto your filament, which is the part of the bulb that actually lights up.
  6. Make five strips. The thinner your wire is before beginning, the better. Thinner wire will almost always result in a better light.
    • Use a pair of good wire cutters for this.
  7. Watermark wikiHow to Make a Light Bulb
    You want a long braid of wire. It needs to be tightly wound as well.
    • You can make an actual 5-strand braid, or you can just gather the ends together, then twist them like a rope.
  8. Watermark wikiHow to Make a Light Bulb
    For an even better fit, you can tighten the hooks around your iron filament. The more of it touching, the better.
  9. Watermark wikiHow to Make a Light Bulb
    This is your "bulb." It will help protect from shock, but also creates a more concentrated light.
    • Make sure that the jar is clean, and that the label has been removed.
  10. Watermark wikiHow to Make a Light Bulb
    If you have electrical clamps, they will be much safer and easier to use. If you don't, make sure you're wearing rubber-soled shoes and have safety gloves on. Attach one wire to each end of the battery to complete the circuit and "turn on" the light bulb.
    • You can use any battery, but starting small is usually best. C or D batteries (1.5 V each) will do the trick.
    • If you're not getting enough light, try attaching your batteries in series.
  11. This is a simple scientific machine, so their are simple ways to test and fix bulbs that don't work. Here are some tips to get your bulb working:
    • Ensure all the ends are touching. You must have a complete, unbroken circuit to get light.
    • Thin out the filament. Try it with only 3-4 strands. You could also replace the iron with graphite, as mentioned in method one.
    • Add more power. Use a bigger battery, or attach multiple batteries together, for more power and more light.
  12. Advertisement

Community Q&A

Search
Add New Question
  • Question
    Can I use a copper wire as the heating element?
    divine enow
    divine enow
    Community Answer
    Yes, but the copper wires must be thin so as to have greater resistance for more heat. But know that copper is not resistant to heat, so it may melt off after a while, provided there is sufficient current.
  • Question
    How do you to connect the wires with the socket?
    Community Answer
    Community Answer
    DO NOT connect your wires to an electrical socket -- there is far more energy than you can safely handle. Hook this bulb up only to batteries.
  • Question
    What can I use instead of a jar?
    Community Answer
    Community Answer
    A bottle is a great resource to use instead of a jar!
See more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

  • If the light bulb doesn't light up after you've connected the copper ends to the battery, check your connections.
  • Using more than five iron strands to make your filament will increase the brightness of your homemade light bulb.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Warnings

  • Do not touch the filament after it has been lit. It will be very hot for at least ten minutes following its use.
  • Using a battery weaker than 6 volts will not light the bulb well. Using a battery stronger than 6 volts could be dangerous because of weak construction.
  • The filament (the twisted iron wire) might move when putting the cork stopper into the glass jar. Make sure the components are in place before stopping the jar completely.
Advertisement

Things You'll Need

  • Glass jar
  • Fitted cork stopper
  • 1 inch (2.54 cm) nail
  • 3 feet (0.9144 m) shielded copper wire
  • Iron wire
  • 6-volt battery
  • Wire cutter

About This Article

Daniel Stoescu
Co-authored by:
Master Electrician
This article was co-authored by Daniel Stoescu. Daniel Stoescu is a Master Electrician and the Owner and Operator of Home Tech Solutions, LLC in Hampton, Virginia. With over a decade of experience, Daniel specializes in wiring residential, commercial, and light industrial structures. The Home Tech Solutions team has over four decades of combined experience and offers comprehensive solutions for residential electrical needs. This article has been viewed 392,481 times.
221 votes - 74%
Co-authors: 46
Updated: June 27, 2024
Views: 392,481
Article SummaryX

To make a light bulb, start by connecting 5 6-volt batteries end to end using electrical tape. Then, take a piece of copper wire and hook one end onto the positive end of the battery chain and the other end onto a piece of graphite pencil lead. Next, take a second piece of copper wire and attach one end to the graphite. Once the graphite is attached to both copper wires, place a jar over it. Finally, turn on your light bulb by touching the loose end of the second piece of copper wire to the negative end of the battery chain. To learn how to make a light bulb using iron filaments, scroll down!

Did this summary help you?

Thanks to all authors for creating a page that has been read 392,481 times.

Reader Success Stories

  • Kai K.

    Kai K.

    Feb 28, 2017

    "I like how this article made sure that I would stay safe doing this experiment (i.e. recommending gloves and..." more
Share your story

Did this article help you?

Advertisement