Download Article
Download Article
This article was co-authored by wikiHow Staff. Our trained team of editors and researchers validate articles for accuracy and comprehensiveness. wikiHow's Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards.
There are 8 references cited in this article, which can be found at the bottom of the page.
This article has been viewed 258,105 times.
Learn more...
If you're getting crafty with paracord, making a lanyard can be a fun project that can also prove to come in handy in potentially dangerous situations. To make your very own paracord lanyard, all you need are a few supplies and some patience!
Steps
-
![Step 1 Gather your materials.]()
Gather your materials. To make a paracord lanyard, you will need at least 6–13 feet of paracord 550, a metal carabiner clip, snap hook, or metal key ring, a ruler or tape measure, a twist tie (or something to easily mark a the center of the cord), scissors, and a lighter.[1] [2]- The proportions of the paracord can differ depending on how long you want your lanyard to be. For about every foot of paracord length used, you will get about an inch of your braiding knots.[3]
- If you want to make a lanyard using just cobra stitching, you may only need about 6–8 feet of paracord. However, if you want to make a king cobra stitched lanyard, you may need about 13 feet.
- For example, 8 feet of paracord will yield about 8 inches of braiding knots for your lanyard.[4]
-
![Step 2 Mark the center of your paracord.]()
Mark the center of your paracord. Fold your long, 6–13 foot paracord in half. At the top of the fold, mark the center by tying a twist tie or rubber band around the paracord.[5]- You can really use whatever kind of marker you want, just make sure that it can stay put as you make your knot, and then easily be removed.
Advertisement -
![Step 3 Tie a lanyard knot.]()
Tie a lanyard knot. If you are tying this knot for the first time, it may be beneficial to use a sheet of paper to visualize how the cords intertwine to tie the know. Poke two holes vertically, on top of each other, about 4 inches apart through the middle of the paper. Feed the loose ends of the paracord through the holes in the paper, and have the looped end of the cord on the left side of the paper, while the loose ends through the paper go off to the right. Pull the cords all the way through the paper so there is no visible loop hanging on the left side, but rather, the "loop" is flush against the paper. You will need about a two-inch loop by the time you’re finished with the knot, so having the cords pulled flush against the paper can help you achieve this. Lay the paper flat on a table.- Take the paracord passing through the bottom hole of the paper, and make a loop near the paper hole.
- Then take the paracord passing through the top hole, and place it underneath the bottom paracord’s loop. Have the cord sit through the middle of the loop. For example, the top cord should look like a center “pupil” running through an “eyeball” (the loop). Also place the upper cord underneath the bottom loop’s tail cord.
- Feed the tag end of the top paracord down through the right side of the “eyeball,” underneath the “pupil,” and up through the left side of the “eyeball.” Gently pull both tails of the cords to tighten the knot just a little bit. You should have a very elaborate and mirrored knot pattern.
- Take the tag end of the paracord coming from the bottom of the knot, bring it around to "trace" the right of the knot, past the top hole where the other cord is coming from, and underneath all of the upper cords, to come up through the “eyeball” center. The same technique will be used for the other tag end of the paracord.
- Bring the upper paracord tail around to "trace" the left of the knot, past the bottom hole where the other cord is coming from, underneath all the lower cords, to come up through the “eyeball” center of the knot.
- Tear off the piece of paper, and hold onto the looped cord that was on the other side of the paper. Gradually pull and tug on both tag ends of the paracords while holding onto the looped cord. Make sure the looped side of the lanyard knot has about a two-inch loop.
- The center of the paracord (marked) should be in the middle of that two-inch loop.[6]
-
![Step 4 Make a simple overhand knot.]()
Make a simple overhand knot. If the lanyard knot seems too complicated and intricate, you can make a simple overhand knot.[7] From the looped portion of the paracord, pinch down the paracord about 2 inches from the top of the loop. Twist the loop over the tag ends to make another larger hoop, and pull the center of the looped paracord through the middle of the larger hoop.
-
![Step 1 Connect the paracord to the carabiner.]()
Connect the paracord to the carabiner. Feed the two loose ends of the paracord through the loop of the carabiner clip, snap hook hole, or metal key ring.[8] Pull the ends through the loop until the lanyard knot is about 5 inches away from the base of the clip.[9]- If the snap hook hole is pretty wide, you can loop the ends of the cord around one more time, to take up more of the wide space.[10]
-
![Step 2 Cobra stitch the paracord.]()
Cobra stitch the paracord. The two end sides of the paracord are the two cords you will be knotting to create the cobra stitch. You will be knotting onto the two center cords running 5 inches down from the base of the carabiner. Take the left hand paracord, and fold it to the right, over and across the two center cords.[11] Then take the right hand paracord, and pass it on top of the tail end of the left side paracord, under the two center cords, and up through the loop created by the left hand paracord.[12] Then pull the loose ends tight.- To make the next knot, follow the same instructions, except reversed to the other side.[13] Take the right hand paracord, and fold it to the left, across the two center cords. Then take the left hand paracord, and pass it on top of the tail end of the right side paracord, under the two center cords, and up through the loop created by the right hand paracord. Then pull the loose ends tight.
- As you continue to knot, you are going to alternate which side of the paracord gets crossed over the two center cords to make the first loop.[14] For example, for the first knot, you made the loop starting with the left hand paracord. For the next knot, start the loop with the right hand paracord. For the knot after that, start the loop with the left hand paracord, and so on and so forth.
- Keep cobra stitching over the two center cords until you get 11 knot bumps on each side of the lanyard.[15] If this lanyard is satisfactory to you, you can cut off the excess pieces and melt the loose ends to the rest of the paracord. However, if you want to use up the rest of your paracord, you can do a king cobra stitch.
-
![Step 3 King cobra stitch the paracord.]()
King cobra stitch the paracord. A King cobra stitch uses the same technique as a cobra stitch, it is just done on top of an existing cobra stitch, and makes the lanyard a bit thicker.[16] Continue cobra stitching the paracords back toward the carabiner end using the same, alternating sides stitching technique you used earlier. Begin by making the first loop with the paracord that has just gone under a loop.- You can tell which paracord this is by looking at the sides and seeing which paracord is coming out underneath a bump loop on the lanyard.[17]
- While making the king cobra stitches, you may need to use your fingers to push the knots up toward the top to make them even.[18] However, the king cobra stitch sides will naturally end up matching up with the spaces in between the original cobra stitches.[19]
-
![Step 4 Cut and melt the loose ends.]()
Cut and melt the loose ends. When you are finished king cobra stitching all the way back down to the end of the carabiner, cut off the loose ends of paracord. Leave about ¼-inch space on the snipped ends.[20] Melt each snipped end with a lighter, using the lower, darker part of the flame to melt the paracord rather than burn it.[21] After about 5-10 seconds of melting the paracord end, push the paracord against rest of the lanyard with the metal part of your lighter.[22] This will help cool the melted paracord and connect the melted end to the rest of the lanyard.- Do this same melting procedure for the other snipped end of the paracord.[23] When both loose ends of the paracord are melted and secure, you are ready to use your paracord lanyard.
Community Q&A
-
QuestionWhat if we don't have paracord? Can we use something else?
Community AnswerThis knotting technique can be used with nearly every type or cord or string, but in order to make a real paracord lanyard, you must use paracord.
Video
Tips
-
Always use more paracord than you think you’ll need. You don’t want to get all the way toward the end of your project, only to find out you don’t have enough paracord.Thanks
References
- ↑ http://survival-mastery.com/diy/useful-tools/paracord-lanyard.html
- ↑ http://www.homemade-gifts-made-easy.com/paracord-lanyard.html
- ↑ https://www.youtube.com/watch?v=YBwwqB153Ys
- ↑ https://www.youtube.com/watch?v=YBwwqB153Ys
- ↑ http://www.homemade-gifts-made-easy.com/paracord-lanyard.html
- ↑ http://www.homemade-gifts-made-easy.com/paracord-lanyard.html
- ↑ http://www.homemade-gifts-made-easy.com/paracord-lanyard.html
- ↑ http://survival-mastery.com/diy/useful-tools/paracord-lanyard.html
- ↑ http://www.homemade-gifts-made-easy.com/paracord-lanyard.html
- ↑ http://www.homemade-gifts-made-easy.com/paracord-lanyard.html
- ↑ https://www.youtube.com/watch?v=gRo7NrLo-tI
- ↑ https://www.youtube.com/watch?v=gRo7NrLo-tI
- ↑ https://www.youtube.com/watch?v=gRo7NrLo-tI
- ↑ https://www.youtube.com/watch?v=gRo7NrLo-tI
- ↑ http://www.homemade-gifts-made-easy.com/paracord-lanyard.html
- ↑ https://www.youtube.com/watch?v=cfrmdrM05r0
- ↑ http://www.homemade-gifts-made-easy.com/cobra-stitch.html#kingcobra
- ↑ http://www.homemade-gifts-made-easy.com/cobra-stitch.html#kingcobra
- ↑ http://www.homemade-gifts-made-easy.com/cobra-stitch.html#kingcobra
- ↑ http://www.homemade-gifts-made-easy.com/paracord-lanyard.html
- ↑ https://www.youtube.com/watch?v=YBwwqB153Ys
- ↑ https://www.youtube.com/watch?v=YBwwqB153Ys
- ↑ https://www.youtube.com/watch?v=cfrmdrM05r0
About This Article
To make a basic paracord lanyard, start by folding a length of paracord in half. The paracord should be about 6 to 13 feet (2 to 4 meters) long. You’ll get about 1 inch (2.5 centimeters) of braid for every foot (30.5 centimeters) of cord, so use more paracord if you’re making something long, like a whistle lanyard. After folding the cord, mark the center with a twist tie. Then, knot the lanyard just below the fold you made to create a small loop. The simplest way to do this is with an overhand knot. Pinch the 2 sides of the cord together about 2 inches (5 centimeters) below the middle of the cord where you put the twist tie. Fold the looped end of the cord over the lengths to make a second loop, then pull the looped top of the cord through the new loop you just made. Pull the knot tight. Pull the ends of the cord through the loop of a carabiner clip or a keyring. Leave about 5 inches (13 centimeters) of cord between the carabiner and the knot you made earlier. Turn the whole thing over so the knot is facing down and the carabiner is at the top, with two long tail ends of cord trailing out behind it on either side. Grab the left-hand tail cord and pass it in front of the 2 central lengths of cord, then behind the right-hand tail cord. Pass the tail of the right-hand cord behind the left-hand tail cord, which is now on the right side. Weave the tail over the 2 central lengths of cord and then under the loop of cord on the left-hand side. Pull the tails of the cord tight to complete the first knot of your braid. Repeat the process again, but this time in reverse—you’ll weave the left-hand tail cord under the central cords instead of over them, and pass the right-hand cord over the central cords and down through the new loop on the left side. Keep doing this until you’ve created the number of knots you want. When you’re done, snip off the loose ends of the cord. Burn the cut ends with a lighter flame for 5-10 seconds to melt the fibers and prevent fraying. For more tips on doing cobra and king cobra stitching, read on!
