PDF download Download Article
Low-cost and low-effort crafts for a lower stress level
PDF download Download Article

Stress balls are easy to make from easily available materials. All you need is a few balloons and the right material to put in them. If you want your stress ball to feel more similar to a commercial stress ball, the sewing method may give you the results you're looking for.

Method 1
Method 1 of 2:

Making a Stress Balloon

PDF download Download Article
  1. Don't use water balloons, which are too thin and weak for this purpose, and will easily burst.[1]
  2. For a typical palm-sized stress ball, you'll need approximately 160 to 240 grams (5.6 to 8.5 oz) of filling. Any of these will do:
    • For a firm stress ball, use flour, baking soda,[2] or cornstarch (a white powder called cornflour in the Commonwealth).
    • For a looser stress ball, use dry rice lentils, small beans, or split peas, or fine play sand from a hardware store.
    • Mix a small amount of dried rice into flour for something in between. This is also more durable than flour alone.
    Advertisement
  3. Watermark wikiHow to Make a Stress Ball
    This isn't always necessary but can be useful if the balloon isn't elastic enough to fit the filling. Blow it up to about 3 to 5 inches (7.6 to 12.7 cm) across, then pinch the neck shut without tying it.
    • This is easiest to do with a clip or assistant to hold it closed.
    • This can make the filling process messier if the air escapes while you're filling it.
  4. Watermark wikiHow to Make a Stress Ball
    If you do not have a funnel, spoon the filling into a plastic bottle instead, and fit the balloon over the neck. A plastic cup pinched to form a spout will work too, but tends to make a mess.[3]
  5. Watermark wikiHow to Make a Stress Ball
    For a typical palm-sized ball, you'll want to fill the balloon approximately 2 to 3 inches (5.1 to 7.6 cm) deep. Pour slowly to avoid clogging the neck of the balloon.
    • If it clogs, use a pencil or spoon handle to clear the opening.
  6. Watermark wikiHow to Make a Stress Ball
    Remove the balloon from the funnel and let out as much air as you can. Tie the neck of the balloon closed tightly.
    • To release the air, pinch near the neck and separate your finger and thumb slightly. Too wide an opening can blow flour everywhere.[4]
  7. Watermark wikiHow to Make a Stress Ball
    Use a sharp pair of scissors to cut off the dangling end of the balloon. Don't try to cut too close to the knot, or it could come undone.
  8. Advertisement
Method 2
Method 2 of 2:

Sewing a Stress Ball

PDF download Download Article
  1. Watermark wikiHow to Make a Stress Ball
    You can find the rubber ball from children's toy stores, and memory foam at some fabric stores or specialized online stores.[5] You'll want a piece of memory foam roughly 3.5 x 5 inches (9 x 12.5 cm) in size, and anywhere from 1 to 3 inches (2.5–7.5 cm) thick. A thicker piece of memory foam will make a softer, more squeezable stress ball.
  2. Watermark wikiHow to Make a Stress Ball
    Wrap the foam around the rubber ball and sew the memory foam together with needle and thread to enclose the ball completely. Snip off excess memory foam if necessary to make a rough spherical shape.
  3. Watermark wikiHow to Make a Stress Ball
    An old sock will provide a durable outer covering, but you can use a thick piece of fabric instead. Snip the sock or fabric to make it a tight sphere around the memory foam. Your squeeze ball is now complete.
  4. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Things you'll need

Balloon method:

  • One balloon (not a water balloon)
  • 160 to 240 grams (5.6 to 8.5 oz) flour, baking soda, cornstarch, fine play sand, dried rice, lentils, beans, or split peas
  • Funnel or plastic bottle

Sewing method:

  • Needle and thread
  • Sock
  • Memory foam
  • Small rubber ball

Reader Videos

Submit a Video Tip!

Share a quick video tip and help bring articles to life with your friendly advice. Your insights could make a real difference and help millions of people!

Submit a Video

Tips

Show More Tips

Tips from our Readers

  • Use a different and darker-colored filling so that your stress ball will change color when squeezed. For example, you could put a blue filling inside a yellow balloon.
  • It's a good idea to use two or three balloons. Then if your ball pops or one of the balloons gets a hole, you won't make a big mess.
  • I recommend using Play-Doh or kinetic sand for the filling!
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Warnings

  • Fillings with water or salt can weaken the balloon rubber and wear out the stress ball more quickly.
  • Wrapping multiple balloons around your stress balloon will add more friction, making it more likely to break.
Advertisement

About This Article

Luba Lee, FNP-BC, MS
Medically reviewed by:
Board-Certified Family Nurse Practitioner
This article was medically reviewed by Luba Lee, FNP-BC, MS. Luba Lee, FNP-BC is a Board-Certified Family Nurse Practitioner (FNP) and educator in Tennessee with over a decade of clinical experience. Luba has certifications in Pediatric Advanced Life Support (PALS), Emergency Medicine, Advanced Cardiac Life Support (ACLS), Team Building, and Critical Care Nursing. She received her Master of Science in Nursing (MSN) from the University of Tennessee in 2006. This article has been viewed 593,278 times.
12 votes - 70%
Co-authors: 62
Updated: June 24, 2024
Views: 593,278
Categories: Balloon Crafts
Article SummaryX

To make a stress ball, slip a funnel into the neck of a sturdy balloon. If you want to make a firm stress ball, pour flour, baking soda, or cornstarch into the balloon. If you want your stress ball to be softer, use lentils, split peas, or fine play sand. You can also mix a little rice into your filling if you like. Slowly pour your filling into the funnel, and use a pencil to clear the funnel if it gets clogged. Pinch out any excess air and tie the balloon closed, then snip off any excess rubber from the end of the balloon. To learn more from our Medical Expert co-author, like how to sew a stress ball together, keep reading the article!

Did this summary help you?

Thanks to all authors for creating a page that has been read 593,278 times.

Reader Success Stories

  • Janice Tay

    Janice Tay

    Dec 9, 2019

    "Stress balls are great! This article really helped me because everything was written so clearly and it was easy to..." more
Share your story

Did this article help you?

Advertisement