This article was co-authored by Roger Judd and by wikiHow staff writer, Sophia Bell. Roger Judd is a Firearms Instructor based in Mesa, Arizona. Roger and his team at Concealed AZ have been teaching NRA, Arizona Concealed Carry, group and individual firearms training classes as well as promotional, corporate, TV & media machine gun events since 2008. As an NRA Instructor, Roger specializes in teaching people how to safely use rifles, pistols, and shotguns.
This article has been viewed 143,903 times.
The length of pull (LOP) is the distance between the center of the trigger and the back center of the butt plate or recoil pad. A proper LOP is necessary to ensure the shooter can shoulder the weapon comfortably and it also puts the head and eye into the correct position to use the sights or scope. Keep in mind that you must follow all rules and regulations concerning firearm ownership and operation in your area.
Steps
-
Begin with an unloaded firearm. You’ll be touching the trigger, so it’s imperative that your rifle is unloaded for these tests. Remove all ammunition and clear the chamber before beginning.
-
Measure the distance between the trigger and the butt plate or recoil pad. Use a tape measure to find the distance between the center of the trigger and the center of the back of the butt plate or recoil pad. This is the LOP of the rifle.Advertisement
-
Write down the measurement. In case the LOP turns out to be too long or short, you’ll need to know the measurement to determine if your stock should be trimmed or replaced.
- Most factory rifles have an LOP between 13.00 and 13.75 inches (33.0 and 34.9 cm).
-
Rest your index finger on the trigger face and bend your arm 90 degrees. Make sure the firearm is still unloaded before beginning. Hold the gun with the hand you generally shoot with. Extend your arm first, then, with your index finger resting on the trigger face, bend your elbow 90 degrees.
-
Ensure the butt plate is nestled in your elbow. The LOP is too long if you are unable to bend your elbow. If there’s more than 1 inch (2.5 cm) of space between the butt plate and the crook of your elbow, the LOP is too short.
-
Shoulder the firearm as though you are about to shoot it. Though you may take shots from many different angles or positions, choose the one that you use most often. With the gun still unloaded, set up as you normally would to take a shot.
-
Check the distance from the thumb of your firing hand to your nose. The firing hand should be holding the wrist of the stock. Generally, the thumb of the firing hand should be 1.5 inches (3.8 cm) from your nose. The LOP is too long if the distance is greater, and too short if the distance is less than 1.5 inches (3.8 cm).
-
Shorten the LOP by removing the recoil pad. If the LOP is too long for you, you can remove the recoil pad for a quick fix. However, this means your shoulder will absorb more of the impact when you fire the weapon.
-
Lengthen the LOP by adding spacers or a thicker recoil pad. If the LOP is too short for you, you can easily replace the recoil pad with a thicker one. Or, you can add spacers between the stock and the buttplate or recoil pad.
-
Get the stock trimmed or replaced by a gunsmith. For best results, take the rifle to a local gunsmith and ask them to trim the stock to the correct size or replace the stock with a longer one, depending on the intended LOP. They’ll take into account the space to add a new butt plate or recoil pad, too.
Expert Q&A
Tips
Expert Interview
Thanks for reading our article! If you’d like to learn more about firearms usage and safety, check out our in-depth interview with Roger Judd.
About This Article
The length of pull (LOP) is the distance between the trigger and the back of your rifle’s butt, and it’s important to get it right so you can shoulder your weapon and use the scope. Take your measurements with an unloaded gun, since your finger will be on the trigger. Measure from the trigger to the back of the recoil pad or butt to determine whether you should trim the stock or get it replaced. To test the gun, hold it unloaded with your index finger on the trigger and your arm bent at 90 degrees. The butt should be able to rest on your shoulder when you bend your elbow. If you can’t bend your elbow all the way, the butt is too long. However, if there’s a gap between the butt and your shoulder, the stock is too short. Similarly, your LOP is too short if the thumb on your firing hand is less than 1.5 inches from your nose, and too long if the distance is greater. For tips on how to shorten the LOP of your rifle, keep reading!
Reader Success Stories
-
"Simple to understand information. Appreciate the citations listed. Should be very useful for first timer setting up cz 457 at one."..." more