How to Prepare a Working Model of a Windmill

Author Info

Last Updated: July 31, 2024 Tested

Building a working scale-model of a windmill is a great craft project for school or just for fun! Create a basic pinwheel model, assemble a tin can windmill, or build a windmill with a milk jug base! Once you've got your windmill assembled, observe how the spinning blades convert wind into energy!

Method 1

Method 1 of 3:

Constructing a Basic Pinwheel

Download Article

Cut each sheet of paper into a 14 cm square. Glue the 2 squares of paper together—make sure the patterned or colored side of the paper is facing out. Allow the glue to completely dry.^{[1]
X
Research source}
Retrieve your ruler and pencil. Place the ruler on a diagonal between 2 corners. Lightly draw a diagonal line from 1 corner to the other. Lightly draw a diagonal line between the remaining 2 corners to create a “X.” Make a 5 cm cut along each line—from the corner towards the center.^{[2]
X
Research source}

Advertisement
Carefully fold 1 corner at a time towards the center. Dab a dot of glue on the center of the pinwheel and adhere the corner. Hold the corner between your thumb and forefinger until it dries. Fold and glue the remaining 3 corners.^{[3]
X
Research source}
Once the glue has dried, position the plastic straw along the center of the backside of the pinwheel—the top of the straw should not poke out above the top of the pinwheel. Secure the straw to the pinwheel by inserting the thumbtack through the center of the pinwheel and the plastic straw.^{[4]
X
Research source}
5
Attach a motor to the pinwheel to create a power-generating windmill. Remove the pinwheel from the straw.
- Place 3 to 4 strips of masking tape over the center of the pinwheel.
- Insert the shaft of a small motor and cover the end of the shaft with a cap, piece of cork, or a small blob of clay.
- Connect the motor wires to the light bulb with alligator clip leads.
- Hold the pinwheel in front of a fan and witness the lighting of the bulb!

Method 2

Method 2 of 3:

Constructing a Tin Can model Windmill

Download Article

Before starting the project, wash and dry your tin can thoroughly. Measure the can’s circumference and evenly divide the can into 6 or 8 lengthwise parts—these will become the blades of your windmill. Use a permanent marker to mark these segments on the can.^{[5]
X
Research source}
Put on your safety goggles and gloves. Use your scissors to carefully cut along the outline of each blade. Stop cutting ½ in from the bottom of the can.^{[6]
X
Research source}
With your gloved hands, carefully bend each blade down towards the surface you are working on. Retrieve your hammer. Place the tin can on the ground and gently tap each blade until it is flat.^{[7]
X
Research source}
4
Sand the tin can. Keep your gloves on and grab the sandpaper. Slowly run the paper over the front and back surface of the can. Pay particular attention to sanding the edges.^{[8]
X
Research source}
- Sanding the can will allow the paint to adhere to the surface.
Spread newspaper or cardboard on the ground. Place the tin can on the covered surface. Put on your protective mask. Spray a thin layer of paint over the blades and center of the tin can. Allow the paint to dry before applying 2 coats of polyurethane spray.^{[9]
X
Research source}
Retrieve the dowel. Lay the tin can windmill on top of the wooden dowel. The dowel should intersect the tin can blade’s center.^{[10]
X
Research source}
Hold the wooden dowel in place—ask a friend or an adult to help. Tap a nail through the center of the tin can and into the wooden dowel. Wiggle the nail around to create a larger hole. This will allow the blades to turn.^{[11]
X
Research source}

Method 3

Method 3 of 3:

Constructing a Milk Jug Windmill

Download Article

Wash the milk jug with soapy water. Rinse it out with clean water several times. Leave it to dry upside down over a towel.
Once dry, flip the jug over. Measure out 2 cups of gravel—dried beans would work too. Carefully pour the gravel into the milk jug.
Retrieve your sharp pen or pencil. Place the sharp end of the writing instrument halfway up the side and in the center of the jug. Poke it through 1 side and out the other to create 2 parallel holes.^{[12]
X
Research source}
Push 1 end of the straw through the middle of the wine cork. Make sure it is a tight fit! If you straw is made of soft plastic, you may need to carve out a bit of the cork in order to insert the straw.
Push the end of the straw without the cork through holes in the base. Use a paperclip, or glue, to attach the pinwheel to the end of the straw without the wine cork. Make sure the pinwheel can spin freely without falling off.^{[13]
X
Research source}
Cut a length of thread between 24 and 32 inches long. Tie one end around the wine cork. Attach the other end to the second paper clip. Blow on the pinwheel, set it outside, or place it in front of a fan and observe what happens to the paperclip!^{[14]
X
Research source}

Community Q&A

Search

Add New Question

Question

Is there an easier method to make a model windmill in one day?

Community Answer

You can easily make a windmill with these steps. Cut out two rectangles and paste them on top of each other like a cross shape. Easily make a body of a windmill with a hexagon and polygons extending down from the sides of the hexagon. Use a sharp object to make a hole in the middle of the cross section of the fan. Use a motor, battery (in a battery holder), switch and wires to connect them all together. The order does not matter. Figure out this circuit for it is exceptionally easy; just connecting it all.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 28 Helpful 57
Question

What is card stock paper?

Community Answer

Card stock, also called cover stock or pasteboard, is a paper stock that is thicker and more durable than normal writing or printing paper, but thinner and more flexible than other forms of paperboard.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 39 Helpful 44
Question

What kind of motor would I need for this windmill?

Community Answer

You will need a DC Motor of 6 volts or above. Any motor below 6 volts won't light up the LED or whatever you have connected.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 22 Helpful 14