PDF download Download Article PDF download Download Article

Removing wall tiles is different, and more difficult, than removing floor tiles because wall tiles are typically set very close together, with minimal grout lines. This means that it takes more care to remove a wall tile without damaging the surrounding tiles.

Easiest Way to Remove Wall Tiles

Work in a horizontal line across your starting wall, and scrape off the grout between the tiles with a utility knife. Insert a chisel between the tile and the wall, then tap the handle of the chisel with a hammer to loosen the tile. Pull the chisel toward you to remove the tile from the wall.

Part 1
Part 1 of 2:

Preparing for Removal

PDF download Download Article
  1. Watermark wikiHow to Remove Wall Tiles
    Wear wrap-around safety goggles, a long sleeved shirt, pants, and work gloves to protect yourself from sharp tile fragments, even if you plan to avoid breaking them. Clear the surrounding area and lay down cloth or tarp to protect fragile surfaces and make cleanup easier.[1]
    • Protect ceramic shower pans and bathtubs from falling tiles by covering them with cardboard.[2]
    • Cover any drains as well, such as by putting tape over them.
  2. Watermark wikiHow to Remove Wall Tiles
    The rest of this section is dedicated to removing grout, which somewhat reduces the chance of breaking the tiles, and makes them much easier to remove. While removing more grout will always help, most people save time and only remove it in the most important areas:
    • When removing a single tile, remove the grout on all sides of it to avoid damaging the others around it.
    • If you are removing an entire wall of tiles, just make sure to remove grout next to the ceiling and floor.
    Advertisement
  3. Watermark wikiHow to Remove Wall Tiles
    Wall grout is typically easy to remove, but a heat gun or blow dryer can soften hard grout if necessary. If you're only managing to scrape away tiny amounts a time, spend thirty seconds warming up the grout line and try again.
  4. Watermark wikiHow to Remove Wall Tiles
    This method takes a while, but comes with a low risk of damaging the surrounding tiles. Fit your utility knife in a sturdy holder if you have one, and run it carefully and repeatedly around the tile or tiles you plan to remove.[3]
    • An ordinary grout saw typically does not work for wall tiles, because of lug spacers that connect adjacent tiles underneath the grout.
  5. Watermark wikiHow to Remove Wall Tiles
    A dremel or other small rotary grinder can remove grout faster than a knife, but can break tiles much more easily if your hand slips. Set the tool to the lowest setting and move it slowly along the grout line. If you have firm control over the tool and the tiles don't crack when you nick them, you can consider increasing the speed of the rotor.
    • You may need to purchase an extra-small head attachment in order to fit between the tiles.
  6. Watermark wikiHow to Remove Wall Tiles
    You don't need to remove every speck of grout, but get rid of most of it to make tile removal feasible. At minimum, scrape away grout until the metal spacer lugs are visible.[4]
  7. Advertisement
Part 2
Part 2 of 2:

Removing Tiles

PDF download Download Article
  1. Watermark wikiHow to Remove Wall Tiles
    If you plan to remove a whole wall of tiles, try tapping the edge of each one with a chisel for signs of looseness. The first tile is much harder to remove than the rest, so it's worth taking some extra time to see if you can get lucky. If you locate one, use either of the methods below to remove it.
    • Your best bet is in areas where you've removed the grout, and areas with signs of water damage.
  2. Watermark wikiHow to Remove Wall Tiles
    This approach should let you save more of your tiles for reuse, unless the tiles are unusually well-adhered or a relatively recent installation. Give it a try by inserting a chisel, putty knife, or other flat tool in between the tile and the wall, almost parallel to the wall.[5] Tap the handle of the tool with a hammer until the tile comes away from the wall. You may need to pry it off in two or three places if firmly attached.
    • If the tiles break instead of coming away, try an air chisel instead.
    • Have an assistant wearing leather gloves catch the tiles as they come away, before they fall.
    • The first tile is generally much harder than the rest. Take your time to tap out the first one, then attack the exposed edge of the next tile. Make sure to be very careful near the edges because the tile will chip easily.
    • If you're only trying to replace 1-2 tiles because they're cracked, use masking tape or duct tape to tape off the tiles you want to remove. Then, tap the tiles with a chisel, starting in the middle and working your way out. Once you get some of the tile pulled away, use your chisel to get behind the tile and tap it sideways to remove the rest.[6]
  3. Watermark wikiHow to Remove Wall Tiles
    If your tiles are set directly into the mortar, you'll probably need to give up on saving it and crack it into pieces. Start by using a hammer and chisel to make a hole in the center of the tile, then chisel the cracked tile pieces away, being careful not to damage the surrounding tiles.
    • Eye protection is especially important for this method.
    • Porcelain tiles will break into extremely sharp, glass-like shards. If this happens, consider breaking them from the side with a hammer and chisel instead, to reduce the number of fragments.
  4. Watermark wikiHow to Remove Wall Tiles
    Use a cold chisel to chip away the setting material until the exposed wall surface is fairly even.[7] You may not be able to remove all of the adhesive and grout, but you want to ensure that a new wall tile will sit flush with the surrounding wall tiles once it is installed.
  5. Watermark wikiHow to Remove Wall Tiles
    These are metal objects that may be left behind during removal. You can remove spacer lugs by snipping them off with utility clippers, breaking them off with pliers, cutting them with a utility knife or sanding them down with sandpaper.
  6. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    How do you remove wall tiles without damaging drywall?
    Art Fricke
    Art Fricke
    Home Renovation & Repair Specialist
    Art Fricke is a home renovation and repair specialist and the owner of Art Tile & Renovation based in Austin, Texas. With over 10 years of experience, he specializes in bathroom and kitchen renovations. Art focuses on a single contractor approach to customized renovation work, and performs projects such as installing custom tile showers, fixing tiled shower leaks, replacing cracked tiles, and installing floor and wall tile.
    Art Fricke
    Home Renovation & Repair Specialist
    Expert Answer
    If you're demoing tile that was applied directly to drywall, it's nearly impossible to remove without ripping out the drywall, too. It's best to just rip it all out to the studs and replace the drywall, then retile it. However, if you're doing tile in a shower or another wet area, you should use concrete backer board, rather than drywall, because drywall will crumble after a few years in a moist environment.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

About This Article

Art Fricke
Co-authored by:
Home Renovation & Repair Specialist
This article was co-authored by Art Fricke. Art Fricke is a home renovation and repair specialist and the owner of Art Tile & Renovation based in Austin, Texas. With over 10 years of experience, he specializes in bathroom and kitchen renovations. Art focuses on a single contractor approach to customized renovation work, and performs projects such as installing custom tile showers, fixing tiled shower leaks, replacing cracked tiles, and installing floor and wall tile. This article has been viewed 715,867 times.
77 votes - 93%
Co-authors: 15
Updated: October 4, 2024
Views: 715,867
Categories: Tiles and Tiling
Article SummaryX

To remove wall tiles, start by heating up the grout between the tiles with a blow dryer so it's easier to remove. Then, use a utility knife or rotary grinder to scrape away the grout until the spacer lugs between the tiles are visible. Next, use a chisel and hammer to pry the tiles off of the wall. If you're not planning on reusing the tiles, you can just break them apart with the chisel and hammer instead of pulling them off intact. To learn how to remove the spacer lugs from the wall, scroll down!

Did this summary help you?

Thanks to all authors for creating a page that has been read 715,867 times.

Reader Success Stories

  • Jim Wolf

    Jim Wolf

    Dec 1, 2017

    "I was trying to find an easier softer way to remove tiles. I haven't done an older bathroom remodel and I..." more
    Rated this article:
Share your story

Did this article help you?

Advertisement