PDF download Download Article PDF download Download Article

Breaking your eyeglasses can be frustrating, and you might not always be able to replace them right away. Whether you scratched the lense, lost a screw, or broke the bridge, you can repair your eyeglasses yourself to hold you over until you are able to get a new pair.

Method 1
Method 1 of 5:

Repairing a Broken Bridge Using Glue and Paper

PDF download Download Article
  1. For an effective temporary fix, it is possible to glue your eyeglass back together to repair a break at the bridge (the part that goes over your nose).
    • Clean. Make sure that the two pieces you're trying to glue are clean. (Remove all glue from previous attempts. If it's "super glue", fingernail polish with acetone will work but it's tough on the frames)[1]
    • Get your supplies in place. Gather up the following: Super Glue (Locktite, Krazy Glue, etc), pieces of glossy wrapping paper or thick magazine pages that match your frames, sharp scissors
    • Cut the wrapping paper into thin strips approximating the width of your frames.
    • Glue the paper to your frames, one strip at a time. Use a short piece of paper as a splint across a broken nosepiece or wrap a longer piece around like an ace bandage.[2]
    • Wait for each piece to dry before you add the next.
  2. Advertisement
Method 2
Method 2 of 5:

Repairing a Broken Bridge by Sewing

PDF download Download Article
  1. You'll need a thread, needle, drill, sandpaper, superglue, painter's stir stick, rubber bands, waxed paper, cotton swabs, alcohol or nail polish remover and a hobby knife.
  2. Use sandpaper to clean and rough up the broken area to be glued. Swab the area with some rubbing alcohol or nail polish remover to prepare the surface.
  3. Cut a piece of a painter's wooden stir stick to fit between the temples (aka, the side pieces) of your glasses. Cover your lenses with wax paper to prevent scratching and then wrap a rubber band over one end of the stick and secure it to your glasses. Do the same on the other end.
    • Line the two halves up carefully and be sure the rubber bands are holding things firmly in place. If it wasn't a clean break and there are some gaps, line the pieces up as best you can taking pains to ensure there are some definite points of contact.[3]
  4. Fill the joint at the break with glue; use enough to secure the bridge but not so much that the glue runs out. Squeeze out the glue slowly and neatly to avoid bubbles. As you fill in the joint, be sure that there are no gaps or voids. Use the side of a cotton swab to gently clean up any excess glue; swab it up before it has a chance to dry and get tacky. Set the glasses aside for at least an hour so the glue can dry completely.
  5. Drill two holes. Choose a small drill bit appropriate for the thickness of your eyeglass frames. Take your hobby knife and dig out pilot holes on either side of the newly repaired joint. Place your glasses down on a soft cloth that's been laid on a table top and carefully drill a hole on each side of the break. The holes must be parallel so they can be used to wrap a band of thread around the core joint.[4]
  6. Use a fine needle and four to six feet of thread that matches the color of your eyeglass frames to "sew" the two sides of the repair together for added strength. Pass the needle and thread through the two holes as many times as you can taking care not to pull too hard and put stress on the newly repaired joint. Stop when there's no more room. Fill the drilled holes with glue, soaking the thread and blotting up any excess with a cotton swab. Trim the edges of the thread and allow the glue to dry for at least an hour.
  7. If you want to give extra strength to your repair, you can add this additional step to your process. Do not trim the edges of the thread as above. Instead, after your glue has dried, take the remaining thread from one side and wrap it around the bridge of your glasses from front to back. Make your wrap as neat as possible; some criss-crossing may be unavoidable, but do your best to prevent the wrap from looking bulky. Leave a short end to be trimmed later. Soak the wrap with glue and let it dry for 10-15 minutes. Take the thread from the other side of your glasses and wrap it around the bridge in the opposite direction (back to front). Soak the new wrap in glue and let it cure for a couple of minutes before snipping off the two loose ends. Set your glasses aside for 24 hours before wearing.
  8. Advertisement
Method 3
Method 3 of 5:

Repairing a Broken Bridge with Heat and a Pin

PDF download Download Article
  1. Boil water. Fill a small pot with water and set the flame to "high." Because you're going to use heat for this repair, the frames of your glasses must be plastic for it to work.
  2. Once the water is boiling, hold the broken edges of the glasses over the pot and close enough for the heat to soften the edges.
  3. Push a short pin into one edge and then push the other edge onto the pin. While the plastic is still hot, smooth it over the pin. [5]
    • Never put plastic eyeglass frames directly over a flame.
  4. Advertisement
Method 4
Method 4 of 5:

Replacing a Lost Screw

PDF download Download Article
  1. Eyeglass repair kits are readily available at drugstores and contain everything you need to make a repair--screws, a tiny screwdriver and sometimes a magnifying glass. A newer version of the kit contains longer screws meant to be easier to handle. You insert the screws into the hinges, screw them in and then "snap off" the bottom of the screw to fit the size of the hinge.
    • If you're finding it difficult to line up the hinges on your temple piece and front piece, it could because a hinge mechanism inside the temple piece hinge is holding it back. To correct this, use the hook end of a paper clip, insert it through the temple hinge hole and gently pull it out. To keep the hinge hole in place, insert a second paperclip upright and into the "gap" created when you pulled out the hinge hole. Line up the front piece and temple piece holes and insert and tighten the screw. When you're finished, remove the paperclip from the gap and the hinge hole will slide back into place creating a firm fit for your glasses. [6]
  2. When a screw falls out of the hinge that holds the front and temple pieces of your glasses together, use a toothpick to temporarily take the place of the screw. Line up the temple hinge holes with the front holes and push a wooden toothpick through them as far as it will go. Break or clip off the excess.[7]
  3. Strip the paper off of a twist tie (the kind that come on a bag of bread). Line up the hinge holes and thread the twist-tie wire through them. Twist the wire in place until the temple feels secure. Cut off the edges of the wire so you don't get scratched. You can also use a small safety pin (the ones that are sometimes used with clothing price tags). Insert the pin through the holes to hold the side in place.
  4. Advertisement
Method 5
Method 5 of 5:

Removing or Filling Scratches on Lenses

PDF download Download Article
  1. 1
    Use baking soda and water. First, wipe off both your lenses with a microfiber cloth. Next, mix 1 teaspoon (4.9 mL) of water with 1 tablespoon (15 mL) of baking soda until it forms a paste-like consistency. Then, apply the paste to your lenses and gently scrub your lenses with the substance. After, rinse your glasses with water to wash off the baking soda mixture. This will likely be all you need to remove the scratches![8]
  2. Abrasive cleansers can be used to polish scratched surfaces. Waxy products like Lemon Pledge and Carnauba cleaner wax actually fill light scratches with wax. However, the wax will reduce your visibility and require reapplication every few days. You can also try rubbing alcohol or diluted ammonia. After treating your glasses with one of these products, polish them with a soft cloth, ideally one made especially for cleaning glasses.
  3. Prevent future scratches. Lenses are delicate and should be treated with care to prevent them from getting scratched.
    • Use an eyeglass case. A sturdy, cushioned case will protect your eyeglasses; place them in a case rather than in your pocket or throwing them directly into your purse.[9]
    • Wash your lenses. Clean your glasses every day with soapy water and dry them with a clean, soft cloth made for this purpose.
    • Stay away from unfriendly products. Some products can harm your lenses and should be avoided. Don't use facial tissues or paper towels to clean your lenses and stay away from anti-bacterial soaps when you wash them.[10] Be careful when using hairspray, perfume or nail polish remover--they can remove the coatings on lenses.
  4. Advertisement


Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

  • If a white residue develops on the frames from contact with acetone, try rubbing them with an oil based lotion.
  • Keep glue away from your lenses and your fingers.
  • In a pinch, the go-to method for fixing a broken bridge is simply to wrap tape around it to hold the two pieces in place. Choose a color tape that matches the color of your frames most closely or make a fashion statement and wrap them in a piece of decorative duct tape.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Warnings

Advertisement

You Might Also Like

Advertisement
  1. David Felsted, DO. Comprehensive Ophthalmologist. Expert Interview. 12 August 2021.
  2. http://www.readingglassesetc.com/repairing-eyeglasses/

About This Article

David Felsted, DO
Co-authored by:
Comprehensive Ophthalmologist
This article was co-authored by David Felsted, DO. Dr. David Felsted is a Comprehensive Ophthalmologist based in Flagstaff, Arizona. He specializes in cataract and refractive surgery, micro-invasive glaucoma surgery, ophthalmic lasers, dry eye disease, diabetic retinopathy, and ocular trauma. Dr. Felsted holds a BS in Accounting from Brigham Young University and a Doctor of Osteopathic Medicine from Midwestern University. He completed his Ophthalmic residency at The Medical College of Georgia. This article has been viewed 930,574 times.
81 votes - 54%
Co-authors: 37
Updated: December 22, 2024
Views: 930,574
Categories: Eyeglasses
Article SummaryX

If you lose a screw from your glasses, try purchasing an eyeglass repair kit from a drugstore. These have replacement screws and a tiny screwdriver to make the repair easy. If you can’t find a repair kit, push a wooden toothpick through the hinge holes. You can also wrap a thin piece of wire through the holes and twist it until the temple of your glasses feels secure. If your glasses have a broken bridge, keep reading to learn how to fix it yourself.

Did this summary help you?

Thanks to all authors for creating a page that has been read 930,574 times.

Reader Success Stories

  • Allison Newby

    Allison Newby

    Oct 8, 2016

    "Using super glue worked for me, but I liked the sewing plus glue and the heat plus pins one, too. If I had more..." more
Share your story

Did this article help you?

Advertisement