PDF download Download Article PDF download Download Article

Lamps are a stylish way to bring soft light into a room, but it can be frustrating when your lamp switch stops working. Instead of throwing your lamp away, try installing a new light switch yourself! It’s an easy project that even a beginner can tackle, and you can replace the switch whether it’s located on the lamp itself or on the cord. All you need are a few simple tools and you’ll be out of the dark in no time!

Method 1
Method 1 of 2:

Replacing a Socket Switch

PDF download Download Article
  1. Your new switch can be whatever type you prefer, regardless of the existing switch. For instance, if your lamp has a pull chain but you want to install a 3-way turn knob, all you have to do is buy a 3-way turn switch and a light bulb with 2 brightness levels.[1]
    • You can even replace a socket switch with a cord switch. Just purchase a new socket assembly without a switch and follow the instructions for replacing a cord switch.
    • You can buy a new socket switch from most hardware stores, and they usually cost around $2-$5 USD.
  2. Never take chances when you’re working with electricity. Double-check to be sure that the lamp is unplugged before you start to take it apart.
    Advertisement
  3. At this point, the socket at the top of the lamp should be exposed. On most lamps, this is where the switch is located.
  4. The socket shell is the actual assembly where the switch is located and the light bulb screws in. On most lamps, you can squeeze the socket shell and pull upwards to remove it.[2]
    • If the socket shell is hard to remove, use a screwdriver to pry it loose.
  5. There should be 2 wires attached to the switch. 1 is hot and the other is neutral. The hot wire is usually attached to a brass screw, and the neutral wire is usually attached to a silver screw.[3]
    • The neutral wire is usually marked in some way. It may be a different color, or the insulation may be printed, stamped, or have indentations. Make sure to note this now, since you’ll need to know which wire is neutral when you hook up your new switch.
    • If you can’t identify the neutral wire, look at the plug. The neutral wire is attached to the wider plug blade on a polarized plug. If your plug blades are the same size, you should replace the plug while you’re replacing the socket.[4]
  6. Cut through the wires as close to the switch as possible to ensure you have plenty of wire to work with.[5]
  7. Wire cutters can also be used to strip insulation from wires. Use the wire cutters to make a notch in the insulation around the wires, then clamp down on the insulation with the strippers and carefully pull the insulation away.[6]
    • If you see any strands of wire when you pull away the insulation, it means you cut too deep. Cut off that section and start again.
  8. Use your fingers to wrap the wire tightly around the screw. Be sure to connect the neutral wire to the silver screw and the hot wire to the brass screw.
    • Although sockets will be slightly different depending on the manufacturer, the wires should thread easily through the socket. Make sure the socket is right-side-up and look for wire channels to help you know where to guide the wire.
  9. You should hear the new socket shell snap into place. If there is a screw on the stem of the lamp, tighten it now to hold the socket in place.
  10. If you’ve done everything right, you should be able to use your new switch to turn on your lamp!
    • If the lamp doesn't come on, check the connection in your switch and try again. If this doesn't help, you may need to replace the plug.
  11. Advertisement
Method 2
Method 2 of 2:

Replacing a Cord Switch

PDF download Download Article
  1. Look for printing which says either SPT-1 or SPT-2. The printing is small, so you might have to look carefully.[7]
    • The difference between SPT-1 and SPT-2 involves the thickness of the lamp cord.
  2. Some switches only require you to connect the hot wire. If this is the case, there will be a channel along one side of the switch for the neutral wire.
  3. You may be able to open the casing of the existing switch and remove the wires without cutting them, but if not, use wire cutters to cut as close to the switch as you can.[8]
    • Try to avoid cutting the neutral wire. If you have to cut it in order to remove the old switch, strip the insulation and connect the cut ends of the neutral wire together. If you like, add a plastic connector to protect the wire at the location where you want your new switch to be.
    • If you are adding a cord switch when there wasn’t one before, use a small knife to carefully split the cord where you want your new switch to go, then cut through the hot wire. If your switch requires you to attach the neutral wire, cut through that too.
  4. Use your wire cutters to make a notch in the wire insulation, then gently pull to remove it. Only take off as much insulation as you need to attach the wires to the screws in the switch.[9]
  5. If you only have one screw, it's for the hot wire. If you have to connect both the hot and neutral wires, the hot wire goes to the brass screw, and the neutral wire goes to the silver screw.
  6. Use your fingers to wrap the wires around the screws securely, and make sure there is enough insulation on the wires so that no live wires will be exposed when you close the switch.[10]
    • There should be no visible wires showing when the switch is assembled. All you should see is insulated cord.
    • If the exposed wires are too long, use the wire cutters to snip off a small portion and reattach the wires to the screws.
  7. Make sure that the cover closes securely and there are no bare wires showing around the switch.[11]
  8. If you’re confident that the switch feels like it’s securely connected and there are no live wires showing, it’s time to test out your lamp! If you hooked everything up right, you should be able to plug in the lamp and turn it right on.
    • If the lamp doesn’t turn on, double-check your wiring and try again.
  9. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    How do you change the switch in a ceiling fan?
    Martin Hennum
    Martin Hennum
    Licensed Electrical Contractor
    Martin Hennum is a Licensed Electrical Contractor and Owner of Peach Electric based in Sacramento, California. With over 10 years of experience, Martin and his team specialize in residential and commercial electrical work. They are knowledgeable about new technologies that help clients with future proofing so they save time and money. Martin is passionate about customer service, bringing the best information to clients, and prioritizing safety across projects.
    Martin Hennum
    Licensed Electrical Contractor
    Expert Answer
    First, take the trim cover off—which is the white cover plate. Then, take the switch out and identify which one has power using a non-contact voltage tester. Finally, put that on the correct terminal point on the new switch, screw it back in and install the trim cover back on.
  • Question
    Can you fix a lamp switch?
    Drew Hawkins1
    Drew Hawkins1
    Community Answer
    You can definitely replace a socket switch if it isn't working anymore. Make sure the lamp is unplugged and remove the shade and bulb. The socket shell is the actual assembly where the switch is located and the light bulb screws in. On most lamps, you can squeeze the socket shell and pull upwards to remove it. If it's hard to remove, use a screwdriver to pry it loose. There should be 2 wires attached to the switch. 1 is hot and the other is neutral. The hot wire is usually attached to a brass screw, and the neutral wire is usually attached to a silver screw. Cut through the wires as close to the switch as possible to ensure you have plenty of wire to work with. Then, cut off the ends of the wire and strip away 1⁄2 inch (1.3 cm) of insulation with a pair of wire cutters. Then, use your fingers to wrap the 2 wires tightly around the screw and then push the new socket into the lamp. You can then replace the light bulb, plug in the lamp, and test it out.
  • Question
    How do you a lamp cord switch?
    Drew Hawkins1
    Drew Hawkins1
    Community Answer
    It's actually not too difficult. If you're replacing the switch with a new one, you may not need to cut all of the wires. Some switches only require you to connect the hot wire. If this is the case, there will be a channel along one side of the switch for the neutral wire. You may even be able to open the casing of the existing switch and remove the wires without cutting them, but if not, use wire cutters to cut as close to the switch as you can. Try to avoid cutting the neutral wire. If you have to cut it in order to remove the old switch, strip the insulation and connect the cut ends of the neutral wire together. You can also add a plastic connector to protect the wire at the location where you want your new switch to be.
See more answers
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Warnings

Advertisement

Things You’ll Need

  • Replacement switch
  • Screwdriver
  • Wire stripper/cutter
  • Small knife (if installing a new cord switch)

You Might Also Like

Put Batteries in Correctly Insert Batteries the Right Way
Install Ground RodsThe Ultimate Guide to Ground Rod Installation
Check Earthing at HomeCheck Earthing at Home
Ground an OutletGround an Outlet
F9 E1 Whirlpool Washer Fix the F9 E1 Error Code in Whirlpool Washing Machines
Tell if a Circuit Breaker Is BadTell if a Circuit Breaker Is Bad
Ground Yourself Ground Yourself Electrically & Avoid Static Shock
Repair an Electric Cord Repair an Electric Cord
Find the Fuse Box or Circuit Breaker BoxFind the Fuse Box or Circuit Breaker Box
Use an Anti Static Wrist WrapUse an Anti Static Wrist Wrap
Change a Circuit BreakerChange a Circuit Breaker
Determine when to Use Arc Fault Circuit Interrupters (Af Circuit Breakers)Determine when to Use Arc Fault Circuit Interrupters (Af Circuit Breakers)
Replace the Plug on a LampReplace the Plug on a Lamp
Test a Ground RodTesting a Ground Rod: Multimeters, Earth Electrodes, & More
Advertisement

Expert Interview

Thanks for reading our article! If you’d like to learn more about electrical maintenance, check out our in-depth interview with Martin Hennum.

About This Article

Martin Hennum
Co-authored by:
Licensed Electrical Contractor
This article was co-authored by Martin Hennum and by wikiHow staff writer, Amy Bobinger, BA. Martin Hennum is a Licensed Electrical Contractor and Owner of Peach Electric based in Sacramento, California. With over 10 years of experience, Martin and his team specialize in residential and commercial electrical work. They are knowledgeable about new technologies that help clients with future proofing so they save time and money. Martin is passionate about customer service, bringing the best information to clients, and prioritizing safety across projects. This article has been viewed 186,694 times.
10 votes - 80%
Co-authors: 5
Updated: June 27, 2024
Views: 186,694
Article SummaryX

To replace your lamp switch, unplug the lamp and remove the light bulb and lamp shade. Squeeze the socket shell to remove it from the lamp base, then cut the wires attached to the old switch. Carefully strip about 1/2 an inch of insulation off of the wires, then reconnect the wires to the new switch. Place the new socket shell into the lamp and snap it into place. Plug in your lamp and you're done! If you want to know how to replace a cord switch, keep reading!

Did this summary help you?

Thanks to all authors for creating a page that has been read 186,694 times.

Did this article help you?

Advertisement