How to Replace a Washing Machine Belt

Co-authored by Homer Flores and Hunter Rising

Last Updated: May 7, 2024 References

If your washing machine isn’t spinning and you don’t feel any resistance when you try to rotate the drum, there may be a problem with the main drive belt. Luckily, you can replace a washing machine drive belt on your own using only a few tools. Start by disconnecting your washing machine and removing the access panel so you can find the belt inside. Take the old belt off of the motor and drum before securing the new one in place. When you’re finished, seal up your machine so you can start using it again!

Get Product Support Solve Any Problem

Hi there! Do you have a question about how to use or repair your home appliance? I’ve read the manuals so you don’t have to. Select your product, brand, and model, then ask away!

*

Part 1

Part 1 of 3:

Accessing the Belt

Download Article

1
Disconnect the washing machine from the power and water supply lines. Unplug your washing machine from the wall so you don’t get shocked or electrocuted while you’re working. Locate the water valves on the wall behind or next to your washing machine. Turn the valves clockwise to shut off the water supply completely so it doesn’t leak. Unscrew the lines leading from the valves to the washing machine to disconnect them.^{[1]
X
Research source}
- There may still be water in the lines when you unscrew them, so keep a small bucket or container nearby to catch any that falls out.
- Never work on your washing machine while it’s still connected to power.
2
Remove the access panel on the front or back of the machine. Consult with your washing machine’s user manual to find out the location of the access panel, which is usually on the front or back of the machine. Locate the screws around the access panel and use a screwdriver to remove them. After you loosen the screws, carefully lift and set the access panel cover aside so it’s out of the way.^{[2]
X
Research source}
- The size and location of the access panel will vary depending on your model of washing machine.
- If you can’t find any screws, there may be hidden latches holding the panel in place. Slide a putty knife in the cracks around the access panel to pop the latches loose.
Tip: You can remove the top panel on a front-loading washing machine if you want to allow more light inside so it’s easier to see.

Advertisement
3
Look in the access panel to locate the belt. Search inside of the washing machine for a 1 in (2.5 cm) rubber belt stretched between the motor and the drum. A front-loading machine usually has the belts on the back while a top-loading machine has the belts near the bottom of the drum. If you still have trouble finding the belts, consult with the owner’s manual to locate them.^{[3]
X
Research source}
- Some newer washing machines don’t have belts. If you aren’t able to find any and your washing machine doesn’t work, contact an appliance repair service to check it for you.
- Some top-loading washing machines have the belts underneath the washing machine. Lay down a towel and carefully tilt the washing machine on its side to access the belts if you need to.
4
Unscrew the belt cover if your washing machine has one. The belt cover is a large plastic piece that hides the drive belt and pulleys it attaches to so they don’t get damaged as easily. Locate the screws that hold the belt cover in place, and loosen them with your screwdriver. Set the screws and cover aside while you’re working so they’re out of your way.^{[4]
X
Research source}
- Not all washing machines have belt covers.
5
Pull the old belt off of the drum if it’s still attached. The drive belt connects to a large circular pulley attached to the machine’s drum and a small pulley on the motor. Try sliding the belt off of the pulley first to see if it’s loose enough to come off. If you have trouble pulling the belt off, shimmy your screwdriver underneath the belt and pry it off of the pulleys.^{[5]
X
Research source}
- If the belt broke or snapped, then it won’t be attached to the pulleys. Check the bottom of the machine to see if it fell or dropped.

Part 2

Part 2 of 3:

Attaching the New Belt

Download Article

1
Get a belt that matches the brand and model of your machine. Belt sizes and lengths vary depending on the brand and style, so it’s important to get a perfect fit. First, check the user manual for your washing machine to see if it specifies the part or size you need for your belt. If you can’t find it listed in the manual, search online for the brand and model of the washing machine so you can find the right belt that fits.^{[6]
X
Research source}
- You can buy replacement washing machine belts online or from specialty hardware stores.
- Don’t try using a belt made for another machine, or else it may not fit or work properly.
2
Align the belt around the drum pulley so the flat side faces out. The drum pulley is the large circular part that connects to the machine’s drum. Make sure the belt has the smooth side facing outwards and the grooved side facing inward. Loop the belt over the drum pulley so it fits into the grooves going around it. Let the belt hang loosely from the drum pulley for now.^{[7]
X
Research source}
- Don’t try to loop the belt around the motor pulley yet since it will most likely be too tight to position correctly.
Tip: Wear long-sleeved clothing while you’re reaching inside your washing machine since there may be sharp edges that can scratch you.
3
Secure the belt to the drum pulley with a zip tie. Hold the belt tightly against the drum pulley so they make firm contact with each other. Feed the end of a zip tie through a hole in the drum pulley before securing the end in the clasp on the other side of the zip tie. Pull the zip tie tight so it holds the belt in place against the pulley.^{[8]
X
Research source}
- You don’t need to use a zip tie, but it makes it easier to stretch a tight belt that’s hard to install.
4
Loop the other end of the belt around the motor pulley. Locate the motor pulley, which is the small circular part connected to the machine’s motor and spins the belt. Pull the end of the belt tightly so it stretches around the motor pulley and fits into the grooves. It’s okay if the belt hangs loosely from the drum pulley for now as long as it stays in place where you put the zip tie.^{[9]
X
Research source}
- Consult with the owner’s manual if you have trouble determining which part is the motor pulley.
5
Spin the washing machine drum so the belt aligns on the pulleys. Open the door of the washing machine and reach inside to hold onto the drum. Slowly spin the drum clockwise to rotate the pulley. As the drum spins, the belt will align itself on the pulley and become tight. Keep spinning the drum until you make 1 full revolution to ensure the belt stays in place.^{[10]
X
Research source}
- The drum will get more difficult to turn as the belt stretches on the pulleys.
- You can also try spinning the drum pulley itself, but it may be more difficult.
6
Cut the zip tie off of the belt with a pair of scissors. Spin the drum until you position the zip tie in a place that you can easily reach. Carefully slide one of the scissor blades underneath the zip tie, and squeeze the handles together to cut through it. Pull the zip tie out from underneath the belt carefully so the belt doesn’t slip off of the pulley.^{[11]
X
Research source}
- Don’t leave the zip tie inside your machine since it could cause the belt to slip or cause damage.
- Be careful not to cut the belt, or else it could snap off more easily.

Part 3

Part 3 of 3:

Closing the Machine

Download Article

1
Screw the belt cover back on if you had to remove it. Position the belt cover back over the pulleys and the belt stretched between them. Feed the screws back into the holes and turn them clockwise to secure them in place. Make sure the cover doesn’t restrict or get in the way of the belt, or else the machine won’t work properly.^{[12]
X
Research source}
- You can skip this step if your machine doesn’t have a belt cover.
2
Reattach the access panel cover to seal your machine. Hold the access panel cover against your washing machine so the screw holes line up. Feed the screws back into the holes and tighten them by turning them clockwise. Start from the top of the access panel and work toward the bottom so the panel doesn’t fall out while you’re attaching it.^{[13]
X
Research source}
- If the access panel used latches instead of screws, line up the holes with the latches and slowly push the panel cover back in until it clicks into place.
3
Connect the washing machine to your water and power supplies. Make sure you line up the water valves to the supply lines you originally removed them from, or else the machine won’t work properly. Tighten the ends of the lines to the valves by turning them clockwise as far as you can. Rotate the valve handles counterclockwise to turn the water back on for your machine. Then plug the machine’s power cord back into the outlet.^{[14]
X
Research source}
- If you notice any leaks from the valves, turn off the water and try tightening the lines with a wrench to make them tighter.
4
Test using your washing machine to see if it works. Put a small load of laundry inside your washing machine and turn it onto a regular cycle. Listen for the drum spinning and motor running while you complete the load so you know the belt works properly. When you finish the load, check if the clothes are still soaking wet or if they’re mostly wrung out. If they’re still dripping wet, then the spin cycle didn’t work properly and there may still be problems.^{[15]
X
Research source}
- If the belt replacement didn’t work, call an appliance service company to look at it for you.

Expert Q&A

Search

Add New Question

Question

Do all washing machines have a belt?

Homer Flores
Appliance Repair Specialist
Homer Flores is an Appliance Repair Specialist and Training Manager at PreFix, a home maintenance company out of Austin, Texas. With over 15 years of experience, Homer specializes in home improvement, remodeling, and construction. Homer’s dedication to the PreFix mission of providing hassle-free one-stop-shop service for home care, in addition to their completion of the Capital Factory and Techstars Accelerators, has contributed to their growth of service to over 50 zip codes throughout the greater Austin area.

Homer Flores

Appliance Repair Specialist

Expert Answer

No, they don't. Most modern washing machines don’t use belt-driven systems.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 1 Helpful 4
Question

Does the washing machine have to be put on its side?

Community Answer

Not always. It only needs to be put on its side if it doesn't have a back, side, or top panel to gain access more conveniently.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 4 Helpful 14
Question

If the drive belt is over-tightened on an automatic washer, can it cause damage?

Community Answer

Yes, it can. Go to a hard wear store and tell them what kind of belt you need. It shouldn't cost too much.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 2 Helpful 8

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Consult with your washing machine’s user manual if you have trouble finding the belts or what replacement parts you need.

Thanks
Helpful 1 Not Helpful 1
If you don’t feel comfortable working on the washing machine by yourself, then call a professional appliance repair service to look at it for you.

Thanks
Helpful 0 Not Helpful 0

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Washing machines can be heavy, so ask a helper to assist you if you need to move or tilt it.

Thanks
Helpful 2 Not Helpful 0
Never work on your washing machine while it’s still connected to power since it could shock or electrocute you.

Thanks
Helpful 2 Not Helpful 0