How to Change the Heating Element in an Electric Oven

Download Article

Get your oven back in action with our expert-approved guide

Co-authored by Homer Flores and Savannah Vold

Last Updated: August 22, 2024 Fact Checked

Download Article

Removing the Old Element

|

Installing the New Element

|

Testing the Replacement Element

|

Q&A

If your oven isn't warming up as it should, you might have a bad heating element. Luckily, replacing your baking element is a super simple and easy process, and in this article, we’ll teach you exactly how to do it safely. Read on to learn how to get your lean, mean cooking machine up and running better than ever—we’re coming in hot!

Things You Should Know

Shut off your home's main breaker and unplug the oven to ensure you're working safely. Then, unscrew the old heating element with a flathead screwdriver.
Fit the new element into the oven by lining up the screw holes with the metal screw plates. Then, reconnect the terminal wires.
Restore power to the oven and test that your new heating element works by setting the oven to “bake.” You should feel heat radiating from inside the oven.

Part 1

Part 1 of 3:

Removing the Old Element

Download Article

1
Turn off the power to the oven and remove the racks. Temporarily disabling the electricity is essential to ensuring your safety during the replacement process.^{[1]
X
Expert Source

Homer Flores
Appliance Repair Specialist

Expert Interview. 14 April 2021.} To do this, head to your home's main circuit breaker, find the switch corresponding to the oven, and flip it to the “Off” position. You may find 2 individual breakers, 1 for each of the 120-volt fuses that powers the oven. If so, shut off both breakers by flipping the corresponding switches. Then, pull out the cooking racks in the oven and set them aside.
- If there's no separate breaker for the oven, you may have to flip the breaker for the whole kitchen.
- As an added safety precaution, unplug the oven from the wall to guarantee no electricity is connected to the oven.
- The oven remains unplugged until you're ready to test the replacement element in a later step.
- Removing the cooking racks should provide you with enough space to access and replace the heating element, making it unnecessary to remove the oven door.
2
Remove the base panel covering the heating element. Start by pulling out the cooking racks from the oven. Some ovens have flat metal covers at the bottom to keep the lower baking elements out of sight. To remove 1 of these covers, feel for the grooved lip on the front edge and pull up on it sharply. Then, lift the panel away from its slot.^{[2]
X
Research source}
- If you don't see the curving wire element when you open the oven door, there's a good chance a cover is concealing it.
- Your base panel may also be secured by 1-2 screws. If this is the case, unscrew them with a flathead screwdriver and set them aside before proceeding.
- Not all base panels have raised lips. If this is the case, push down on one corner of the panel to lift the opposite corner enough to grip.
Advertisement
3
Unscrew the element at the front and back with a flathead screwdriver.^{[3]
X
Research source} Loosen and extract the screws at each connection site with a flathead screwdriver. Most heating elements, also called baking coils, have 2 screws on the front side and 2 more along the back, connecting the piece to the rear wall of the oven.
- If the element in your oven is fastened with bolts instead of standard screws, strip them using a ¹⁄₄ inch (0.64 cm) nut driver tool.
- Set the screws aside, like in a small bowl, to avoid losing them. You'll need them again after installing the new baking element.
4
Detach the wires running to the element with needle-nosed pliers. Pull the loose baking coil a few inches from the rear wall to create a comfortable amount of space. Then, use a pair of needle-nosed pliers or your fingers to gently pull or slide the colored wires away from the terminals on the element's backside.^{[4]
X
Research source} Note how the wires are configured (it may be helpful to take a picture) so you'll be able to easily reconnect them once you've installed the new element.
- Be careful not to let the wires slip through the holes in the back of the oven, or you'll have no choice but to pull the entire unit out to thread them back through.^{[5]
  X
  Expert Source
  
  Homer Flores
  Appliance Repair Specialist
  
  Expert Interview. 14 April 2021.} It may help to tape them to the interior wall.
- Heating element wires are sometimes secured with small male-female spade connectors or a thin, interlocking metal slot and insert. These can usually be separated with a quick pinch of your pliers.

Part 2

Part 2 of 3:

Installing the New Element

Download Article

1
Identify the make and model of the old element and purchase a new one. You should be able to make out a brand name, model number, or serial code indicating the part's manufacturer on one of the element's broad metal faces. Alternatively, refer to your oven’s user manual if you still have it to determine the exact heating element you need to ensure you purchase its perfect match.^{[6]
X
Research source}
- Jot down any identifying info on the element before disposing of it to take to the hardware store if you plan on buying your replacement part in person.
- If you're unable to find the exact model you need in stores, try ordering a replacement online.
2
Fit the new element into the oven by lining up the screw holes. Position the element over the bottom surface of the oven, with the metal screw plates facing down and the terminals facing the rear of the oven.^{[7]
X
Research source} Then, double-check that the screw holes on the element line up with those on the oven.
- Convection baking coils are typically installed on the top of the oven rather than the bottom, like electric ovens, but the installation process is the same.
3
Reconnect the terminal wires using pliers. Grab your pliers again and guide the ends of the replacement part's wires into the terminals on the element's backside. Once the wires are secure, slide the element back until it rests flush against the rear wall of the oven.^{[8]
X
Research source}
- If there are male-female connectors on the ends of the wires, you should hear them click when they're firmly in place.
- Ensure each wire runs to its correct terminal (they should end just in front of their corresponding connection sites) to prevent a possible fire hazard.
- Keep a loose grip on the pliers to avoid damaging the delicate ends of the wires.
4
Screw down the element with a screw or nut driver.^{[9]
X
Research source} Insert the screws into the metal plates on the bottom of the element, 2 in the front and 2 in the back. Tighten them with your screwdriver or nut driver tool to the right until they stop turning. Then, Give the element a gentle shake to feel for loose connections.
- Use a ¹⁄₄ inch (0.64 cm) nut driver tool if your element fastens with bolts instead of screws.
5
Slip the base panel back in over the heating element. If your oven features a separate cover, slip it back over the newly-installed element and press down until it lies flat. Secure any other screws or fasteners before restoring power to the oven.^{[10]
X
Research source}
- Gaps or raised corners could indicate that the base panel has been installed slightly crooked.

Part 3

Part 3 of 3:

Testing the Replacement Element

Download Article

1
Restore power to the oven and put the racks back in. Head back to the circuit breaker and flip the switch for the oven to the “On” position. Remember to hit both breakers if your oven operates on dual fuses. This will direct electricity back to the oven, so it's important to ensure that you've finished making all necessary adjustments by this point. Then, slide the racks back into the oven.^{[11]
X
Research source}
- Don't forget to plug the oven back in if you unplugged it earlier.
2
Test the new baking coil by setting it to "bake." Turn on the oven and set it to “bake” or “convection,” depending on which element you've replaced, and give it a few minutes to warm up.^{[12]
X
Research source} Then, hold one hand up a safe distance from the heating element, careful not to touch it. It shouldn't take long for it to begin radiating heat.
- An active heating element will typically glow red when it's nice and hot.
- Try gradually upping the heat setting to see how well the new element handles higher temperatures.
- The wiring may be wrong if your oven still feels cool after replacing a suspect heating element. Call a qualified electrician and have them diagnose and repair the problem.
3
Watch for smoking. Don't be alarmed if you see a few wisps of smoke escaping from the oven as it heats up—this is just the protective factory coating burning off the outside of the new element and isn’t anything to worry about.^{[13]
X
Research source} That said, it's recommended to hold off on cooking anything until 30 minutes after installing the new element.
- You may also notice a faint acrid odor.
- Heavy or continuous smoke may indicate that one of the oven's components has caught fire. If the smoking doesn't stop after a few minutes, contact your local fire department.

Community Q&A

Search

Add New Question

Question

How long does it take to change an oven element?

Community Answer

I've just done mine for the second time. Changing the element took 10-15 minutes.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 0 Helpful 2
Question

How do I remove the hidden element if the bottom base has no screws and the bottom attached to sides and top are all one piece?

Community Answer

Unfortunately, you will need to remove the back, side, and top of the oven. This is the case with the GE profile.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 0 Helpful 8

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

A flashlight may come in handy to help you identify small components and better see what you're doing inside the oven.

Thanks
Helpful 0 Not Helpful 0
If you’re unsure which oven element is misfiring or broken, testing them with a multimeter may help determine what part is causing the problem.

Thanks
Helpful 0 Not Helpful 0

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Anytime you're working in or around a live oven, there's a heat or electricity-related injury risk. Always take the proper safety precautions, such as turning off the power and unplugging your oven to avoid unnecessary mishaps.

Thanks
Helpful 0 Not Helpful 0