This article was co-authored by Seleh Rahman. Seleh Rahman is a Tailor, Furrier, and the Owner of Seleh de Federal Hill in Baltimore, Maryland. With over 45 years of experience, Seleh specializes in fur, alterations, and fashion illustration. Seleh studied Fashion Design and Tailoring at Bay College of Maryland. He holds certifications in fur, design, and tailoring.
This article has been fact-checked, ensuring the accuracy of any cited facts and confirming the authority of its sources.
This article has been viewed 2,289,361 times.
Sewing buttons is very easy once you get the hang of it. It's a very useful skill to possess, as buttons do fall off.
Steps
-
Choose your button and thread. Select a suitable button and thread that matches the button, the garment, and any thread used to sew on other buttons. If you like, you can double the thread to make this job quicker.
-
Thread the needle. Simply pull the thread through the needle so that there is an equal length of thread extending from both sides.Advertisement
-
Tie a knot at the end of the thread. One way to tie a knot is to wrap the thread around your finger as shown, roll the thread between your fingers, and pull it tight. If you doubled the thread, tie the ends together. Leave a long tail of thread, whether you are doubling the thread or using a single thread to sew the button.
-
Position the button on the fabric. Line the button up with the other buttons on the garment. Also check the buttonhole. Close the opposite flap or panel where you want it and make sure that the button lines up with the buttonhole.
-
Push the threaded needle up through the fabric and through one hole in the button. Pull the thread all the way through on each stitch.[1]
-
Place a straight pin. Place a straight pin beneath the button, between the stitch you have made and where the next stitch will go, in order to keep the button from being stitched too tight. Then, push the needle down through the next hole and through the fabric. Pull the thread all the way through. It's best to hold the button in place so it does not move.
-
Restart the process. Bring the needle up through the first hole again and pull the thread all the way through the fabric.[2]
-
Strengthen the button. Repeat the sewing process enough times to make sure the button is securely in place.[3]
-
On the last stitch, push the needle through the material, but not through a hole in the button.
-
Remove the straight pin.
-
Wrap the thread. Wrap the thread six times around the thread between the button and the material to reinforce the shank you have created.
-
Push the needle back down through the material.
-
Make three or four stitches to secure the thread. Make a few stitches below the button, going back and forth to make them strong. Tie this thread off.
-
Cut off the excess.
-
Choose what you will use. Select a suitable button and thread that matches the button, the garment, and any thread used to sew on other buttons.
-
Thread the needle. If you like, you can double the thread to make this job quicker. Simply pull it through the needle so that there is an equal length of thread extending from both sides.
-
Tie a knot at the end of the thread. One way to tie a knot is to wrap the thread around your finger as shown, roll the thread between your fingers, and pull it tight. If you doubled the thread, tie the ends together. Leave a long tail of thread, whether you are doubling the thread or using a single thread to sew the button.[4]
-
Position the button on the fabric. Line the button up with the other buttons on the garment. Check the buttonhole. Close the opposite flap or panel where you want it and make sure that the button lines up with the buttonhole.[5]
-
Push the threaded needle up through the fabric and through one hole in the button. Pull the thread all the way through on each stitch.
-
Place a straight pin. Place a straight pin beneath the button, between the stitch you have made and where the next stitch will go, in order to keep the button from being stitched too tight.
-
Push the needle down through the opposite hole and through the fabric. Pull the thread all the way through.
-
Repeat through these holes twice, then switch to the other holes.
-
Switch between opposing pairs until the button is strongly attached.
-
On the last stitch, push the needle through the material, but not through a hole in the button.
-
Remove the straight pin.
-
Wrap the thread. Wrap the thread six times around the thread between the button and the material to reinforce the shank you have created.
-
Push the needle back down through the material.
-
Make three or four stitches to secure the thread. Make a few stitches below the button, going back and forth to make them strong. Tie this thread off.
-
Cut off the excess.
-
Finished.
Expert Q&A
-
QuestionHow do you reinforce buttons on a coat?Seleh RahmanSeleh Rahman is a Tailor, Furrier, and the Owner of Seleh de Federal Hill in Baltimore, Maryland. With over 45 years of experience, Seleh specializes in fur, alterations, and fashion illustration. Seleh studied Fashion Design and Tailoring at Bay College of Maryland. He holds certifications in fur, design, and tailoring.
Professional Tailor & FurrierFor this, you'll need a button backing to secure the front button. This way, when you sew on it all together, the top button will come through the hole easily and it will have more security. -
QuestionThe buttons I sewed onto my sweater have a steel loop to sew. How can I get the button not to look like it is falling off? How can I secure it better?Community AnswerPut a little button on the other side of the fabric then sew the button on. The small button on the opposite side of the button will pull the external button straight outward and keep it neatly in place.
-
QuestionDoes a button getting loose mean you're fat?Community AnswerNo, not generally. In some cases it could result from gaining weight, but more likely, the thread just came loose because that just happens over time, or it wasn't sewn on very well in the first place.
Video
Tips
-
For buttons that get heavy use, try wrapping the long thread of the needle tail around the threads that hold the button, at least 4 or 5 times, tightly, then force the needle and thread through the tight bunch of threads that you have created. Try pushing the needle parallel to the button's holes, to avoid resistance. Use a thimble for pushing the needle. (The reason for this is simple: thread wear will cause the button to fall off sooner, unless you wrap the exposed threads with a protective wrap.) Once you have forced the needle through, push it back into the cloth, and tie it off with the long tail that you left at the starting knot. When you wrap the threads, the button will be more secure, and the thread that holds it in place will last much longer.Thanks
-
Another way to knot the thread at the end is to take a tiny stitch on the wrong side, pull it almost down to the fabric, and then put the threaded needle through the loop before pulling it tight. If you do this twice in the same spot, that is a double-knotted thread. Then you can cut off the thread close to the knot.Thanks
-
You can thread two pieces of thread through the needle, doubling each and so using four threads at once, to really speed up the process.Thanks
Warnings
- Take care not to poke yourself with the needle. If you are sewing heavy fabric, use a thimble to push the needle.Thanks
References
- ↑ https://www.sewmag.co.uk/how-to-sew/how-to-sew-a-two-hole-button
- ↑ https://www.ties.com/blog/how-to-sew-a-button
- ↑ https://www.allfreesewing.com/Basics-and-Tutorials/Hand-Sewing-Buttons
- ↑ https://www.apartmenttherapy.com/the-best-way-to-sew-on-a-button-221760
- ↑ https://www.youtube.com/watch?v=gslzx1CreAY
About This Article
To sew a button, first thread a needle and tie a knot at the end of the thread. Place the button on the fabric where you want to sew it, making sure it’s lined up with the corresponding button hole. Then, bring the needle and thread up through one of the holes in the button. Place a straight pin underneath the button next to the stitch you just made, which will prevent it from getting stitched too tightly to the fabric. Next, bring the needle and thread down through the other hole. Repeat the process until the button feels secure. Then, push the needle and thread through the fabric, but this time don’t go through one of the holes in the button. Remove the straight pin, and wrap the thread around the stitching between the button and fabric 6 times. Bring the needle and thread down through the fabric again, and stitch 3-4 more stitches through the holes in the button. Finally, tie off the thread and cut the excess off with scissors. If you’re sewing a button with 4 holes instead of 2, follow the same process but alternate the pair of holes you’re stitching through. For help making your button more secure, scroll down!
Reader Success Stories
-
"I sewed my first button successfully, it was so nice, thanks."