PDF download Download Article PDF download Download Article

Buying replacement razor blades can be a costly expense over time. One razor blade typically lasts just a few months, maybe even less if you have especially thick or coarse hair![1] As your razor dulls with use, you'll notice that it is less efficient. This can result in stubble left behind or a painful pulling sensation when you shave. But with a few tricks to prolong the usefulness of your razor, you can save yourself some bucks by preserving your blades.

Method 1
Method 1 of 2:

Stropping Your Razor

PDF download Download Article
  1. A traditional strop is made of leather, but an old pair of jeans will work almost as well. You should use old jeans as opposed to new jeans or jeans you wear regularly. You'll be using the cloth to rejuvenate the blades on your safety razor, but doing this could cause the fabric of your jeans to fray or deteriorate over time. Use old jeans so you don't do damage to a good pair of jeans![2]
  2. A table or the counter top of your bathroom sink should be suitable as a sharpening surface. Clear the area first; an uneven surface could negatively impact your sharpening, and clutter might obstruct your sharpening motion.
    • You should also make sure the area is dry when using this sharpening technique. For the best results, you'll want to sharpen your blade when it's dry.[3]
    Advertisement
  3. Wash your razor with hot water and soap. Dish soap should work well for busting up any razor gunk that's accumulated on your blades. For best results, allow your razor to soak in a cup of hot, soapy water for 15 to 30 minutes, swirling your razor in the water occasionally.
    • Disinfect your razor with an astringent or alcohol-based cleaner.
    • You might also use a specifically formulated razor blade cleaning solution. These are designed to work especially well on skin and hair buildup. Explore the shaving section of your local pharmacy or online vendors to find a razor blade cleaning solution.[4]
  4. You can remove much of the excess moisture from your razor by holding it firmly and shaking it into the basin of your sink. Then, to ensure the blade is completely dry, you should use a cloth to wipe away remaining moisture. Do this by running your razor along the cloth with a motion that follows the direction of the blades.
    • To prevent fuzz or lint from building up, you might consider using a lint-free or microfiber cloth to dry your razor.[5]
    • Store your razor in a dry spot, like a case or drawer, instead of leaving it in the sink shower, or bathroom, where it's exposed to moisture and likely to rust.
  5. You'll want to do this with the direction of the blades and not against the blades. Do this about approximately 20 times in one direction with short, quick strokes. This process, called stropping, will remove burrs and irregularities from your blades, honing your razor's edge.
    • To evenly and completely strop your blades, you'll want perform the same motion in the opposite direction (on the same section of denim) as well. Switch directions and run the blade along the jean fabric around 20 times in the same fashion you did previously.
    • Use light pressure when stropping. Pressing too hard can actually cause damage to the edge of your blade.[6]
  6. Be careful while doing this; you don't want to cut yourself while sharpening! Use moderate pressure and run the blades of your razor along the straight part of the top of your forearm with the direction of the blades and not against. Use quick, short strokes, and perform this motion about 10 - 15 times.
    • Your arm is very similar to an old fashioned leather strop, which is a piece of leather used for sharpening blades. In the same way a strop sharpens a blade, so should your arm.[7]
    • Since you are running your razor with the blades and not against, your safety razor shouldn't cut the hair on your forearm. Be careful not to slip and run the blade side-to-side, as this could result in you cutting yourself.
  7. Especially dull blades might require more strokes for best results. With the same motion you used for your first stropping, run your blades along the jeans with and not against the direction of the blades. Use light pressure and short, quick strokes for roughly 20 strokes, running your razor back and forth along the jeans, always in the same direction of the blades.[8]
  8. Advertisement
Method 2
Method 2 of 2:

Maintaining Your Safety Razor

PDF download Download Article
  1. Your skin has natural oils that protect it from the environment, but these oils can also harm the quality of your blade over time. Shaving cream and decaying hair can also lead to your razor dulling rapidly. Clean your razor thoroughly after each use to maintain the sharpness of your blades. Use hot water and soap to clean your razor.
    • A good way to remove gunk and grime thoroughly is to use a toothbrush to lightly scrub your razor when you are finished shaving. Then, rinse away the gunk under running water.[9]
    • Use an alcohol-based cleaner or astringent to disinfect your razor.
  2. When your razor is wet, the metal is vulnerable to corrosion and rust. This will cause your razor to dull more quickly. Thoroughly dry your razor when you are done shaving to prevent this. Then, store it in a cabinet, drawer, or case instead of the sink, shower, or counter where it will be exposed to moisture.
    • Many approaches can work for drying your razor. For example, you might use a blow dryer or blot your blades with a towel.
    • Always exercise care when drying your blades. Rushing while blotting your blades with a towel might cause you to accidentally run your fingers along the sharp part of the blade, which could cut you.[10]
  3. You might consider using a mineral oil or a small amount of cooking oil on your blade after drying it. This will coat the outer surface of the blade, making it less susceptible to moisture in the air, airborne dirt, and other environmental factors that can lead to a dull razor.
    • Some companies offer special formulated oils designed to prolong the life of your blade. Search for these in the shaving section of your local pharmacy, or online through a shaving vendor.[11]
  4. Advertisement

Community Q&A

Search
Add New Question
  • Question
    Can I sharpen multi-blade razors?
    Community Answer
    Community Answer
    Yes, you can definitely sharpen these and get more uses out of them. You should also clean them off with rubbing alcohol after using them to make them last longer.
  • Question
    What about the more common multi blade razor cartridges? Can they be successfully sharpened the same way?
    Community Answer
    Community Answer
    No, because it would be nearly impossible to sharpen one blade without damaging the others.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

  • These methods will only prolong the life of your safety razors. You will eventually need to replace the blade.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Warnings

Advertisement

Things You'll Need

Stropping Your Razor

  • Cup (for razor cleaning)
  • Dull safety razor
  • Microfiber cloth (optional)
  • Pair of old jeans
  • Razor cleaning solution (optional)
  • Soap (dish soap, for example)

Maintaining Your Safety Razor

  • Blow dryer (optional)
  • Skin safe blade lubricant (like mineral or cooking oil)
  • Towel (optional)
  • Toothbrush

About This Article

Woody Lovell
Co-authored by:
Professional Barber
This article was co-authored by Woody Lovell. Woody Lovell is the Founder of The Barbershop Club, a gentleman's barbershop-as-social club rooted in 1990's traditional barbering based in the Hotel Normandie in Los Angeles, California. He is also the Founder of his own line of quality grooming products. He has over 20 years of experience in the male grooming industry and has consulted clients including professional athletes, musicians, and A-list actors throughout the Los Angeles area. This article has been viewed 343,206 times.
8 votes - 60%
Co-authors: 13
Updated: September 17, 2024
Views: 343,206
Categories: Razors
Article SummaryX

Before you sharpen your old razor blades, soak your razor in a cup of warm, soapy water for 15-30 minutes to clean it, then let it dry completely. Next, lay an old pair of jeans on a flat, sturdy surface. Use short, quick strokes to run your razor along your jeans, with the direction of the blades, as if you’re shaving. Do this 20 times in one direction on your jeans, then do it 20 times in the opposite direction to remove burrs and other irregularities from your razor blades. For more information on sharpening old razor blades and maintaining your safety razors, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 343,206 times.

Reader Success Stories

  • Nadia Du Plessis

    Nadia Du Plessis

    Jul 17, 2016

    "I am taking the plumes of my jacket off with old razors, but by now they are so blunt they don't even cut my..." more
Share your story

Did this article help you?

Advertisement