PDF download Download Article PDF download Download Article

Cars and older homes that don’t use modern circuit breakers use fuses to prevent damage from electrical surges. Sometimes these fuses require testing to check that they are still in good working order. Testing fuses can be done using a multimeter, and doing so is both fast and easy to learn.

Part 1
Part 1 of 2:

Learning about Fuses and Multimeters

PDF download Download Article
  1. Fuses are really just wires that are designed not to last, but their purpose is to prevent damage to more valuable electrical equipment or prevent fires (especially in homes) caused by power surges. If too much power runs through the fuse, it will "burn out," quite literally, and open the circuit, preventing the current from flowing through the circuit. There are several varieties of fuses, but their differences are primarily in appearance. Here is a description of the two you are most likely to see:
    • The cartridge fuse is a cylindrical fuse that has been common in a wide variety of devices for many years, from homes to small electronic devices. They have metal contact or terminal points on either end and consist primarily of a tube that contains the wire.[1]
    • The blade fuse is a common type of automotive fuse that has come into use in the last 20-30 years. They vaguely resemble the plug of a power cord, with two metal prongs emanating from a plastic housing that contains the wire. Previously, most vehicles also contained small glass cartridge fuses. Blade fuses plug conveniently into banks, and relatively little space is required to house a large number of them together.[2]
  2. Learn how a multimeter works. Multimeters measure AC and DC voltage, electrical resistance, and the flow of current. For testing a fuse, you can either use it to measure the continuity (which tests if the circuit is complete) or the ohms (which tests resistance). [3]
    • A multimeter has a positive and negative lead. When testing resistance in a circuit, the meter will transmit a small quantity of electricity from its own battery and then measure the amount that passes through the circuit or object.
    Advertisement
  3. Understand why you must test fuses. Testing fuses is the simplest way to examine what is going on in the electrical systems of your car or home, and for that reason, it is a vital skill to possess.
    • It is easier to test fuses than it is to test other electrical equipment. Other components in your car or home involve complex wiring systems that run on for some length. In addition, most car parts can only be tested at repair shops, and to do so will usually cost quite a lot of money. Testing fuses with a multimeter is comparatively simple to do, and the equipment involved is cheap and easy to operate.
    • Many types of fuses allow for visual confirmation that the fuse is still functional. They are made clear so that you can see if the wire remains intact. If the translucent area is blackened, it is usually because the fuse has burned out. However, some fuses will create that blackened stain after only slightly overheating, and that may have even been the result of an unnoticed incident weeks or months earlier. If a device is not working, you should test the fuses. If the fuses are all still working, there is likely a more serious problem and it may be time to call on an expert.
  4. Advertisement
Part 2
Part 2 of 2:

Testing the Fuse

PDF download Download Article
  1. Make sure the device, equipment, or vehicle is turned off before the fuse is removed. To remove the fuse, simply pull it straight out of the slot.
  2. Turn the meter on and set it to measure continuity. Turn the dial on the multimeter so it points to the continuity setting, which looks like 5 curved vertical lines. Before you test the fuse, put the positive and negative leads together and listen for the meter to beep to ensure it’s working properly.
    • If you want to measure the ohms, use the multimeter setting that has the omega symbol (Ω).
  3. Because the fuse is little more than a single wire—and no complex parts to worry about—it does not matter which side receives the positive or negative lead.
  4. Listen for the multimeter to beep continuously as you hold the probes against the fuse. If you don’t hear any noise coming from the meter, then the fuse is blown and should be replaced.
    • If you’re using a digital multimeter set to measure resistance, touch the probes together to get an initial reading. Then put the probes on either side of the fuse and check if the reading is similar. If it is, then the fuse works properly. If you get no reading or “OL”, then the fuse has blown.
    • If the multimeter reads "Open" or "Not complete," it means the fuse is broken.
  5. Advertisement


Expert Q&A

Search
Add New Question
  • Question
    When a fuse is broken, what does it read on a multimeter?
    Ricardo Mitchell
    Ricardo Mitchell
    Electrician & Construction Professional, CN Coterie
    Ricardo Mitchell is the CEO of CN Coterie, a fully licensed and insured Lead EPA (Environmental Protection Agency) Certified construction company located in Manhattan, New York. CN Coterie specializes in full home renovation, electrical, plumbing, carpentry, cabinetry, furniture restoration, OATH/ECB (Office of Administrative Trials and Hearings/Environmental Control Board) violations removal, and DOB (Department of Buildings) violations removal. Ricardo has over 10 years of electrical and construction experience and his partners have over 30 years of relevant experience.
    Ricardo Mitchell
    Electrician & Construction Professional, CN Coterie
    Expert Answer
    When a fuse is broken, it reads the circuit is not complete, so it reads an open line.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

  • Household installations these days shouldn't really be protected by just fuses. Modern circuit breakers and protective devices are fuse-less and much safer. Consider having an old fuse installation upgraded to modern standards.
  • Regarding car fuses, most cars use a colored 'blade' type fuse, and looking at the top of the fuse in situ in the fuse box will show that the metal strip that runs along the visible top of the fuse will either be intact (fuse good) or broken (fuse blown).
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Warnings

  • Never replace a blown or suspect fuse with one of a higher rating. The rating ensures that the current can pass through the wiring safely. Always replace a fuse with the same rating as (or a lower rating than) the old one.
  • Never test a fuse on equipment that is still on.
Advertisement

About This Article

Ricardo Mitchell
Co-authored by:
Electrician & Construction Professional, CN Coterie
This article was co-authored by Ricardo Mitchell. Ricardo Mitchell is the CEO of CN Coterie, a fully licensed and insured Lead EPA (Environmental Protection Agency) Certified construction company located in Manhattan, New York. CN Coterie specializes in full home renovation, electrical, plumbing, carpentry, cabinetry, furniture restoration, OATH/ECB (Office of Administrative Trials and Hearings/Environmental Control Board) violations removal, and DOB (Department of Buildings) violations removal. Ricardo has over 10 years of electrical and construction experience and his partners have over 30 years of relevant experience. This article has been viewed 1,213,129 times.
85 votes - 74%
Co-authors: 21
Updated: July 31, 2024
Views: 1,213,129
Article SummaryX

Before you test a fuse with a multimeter, turn off the equipment and remove the fuse by pulling it straight out of its slot. Turn the meter to ohms, then touch the positive and negative leads together and check the reading. Next, put one lead on each end of the fuse and check the reading. If the reading is close to the one you got when you touched the positive and negative leads, the fuse is fine. If the fuse is blown, the meter will not read anything at all, or the meter may say “Open Loop” or "OL." If you want to use the meter as an ammeter, keep reading!

Did this summary help you?

Thanks to all authors for creating a page that has been read 1,213,129 times.

Reader Success Stories

  • David Wright

    David Wright

    Jun 1, 2017

    "I had a storm that sent a power surge and knocked out both Samsung TVs. This article really helped me on how to..." more
    Rated this article:
Share your story

Did this article help you?

Advertisement