PDF download Download Article PDF download Download Article

The clove hitch knot is fairly simple, and it can be useful for securing ropes to trees, posts, or poles. One benefit of this knot is it's fairly easy to adjust the length of the rope if you need to. It's often used in boating and sailing, and you may also use it climbing, as you can tie it with one hand.

Method 1
Method 1 of 3:

Tying a Cove Hitch Knot over an Attached Pole

PDF download Download Article
  1. Move from the front to the back and drag the rope over so the end is hanging off the other side of the pole. Create a length of about 6 inches (15 cm) to work with on the end rope, which should be on the other side of the pole.[1]
    • You can leave a longer end if you want, but it will hang out at the end. You need enough to go around the pole at least twice.
    • You may need to increase the length if you are working with a larger diameter.
    • Always keep your eye on where the ends of the rope are in comparison to one another. That makes it much easier to follow.
  2. Bring the running end under the pole and then over the part of the rope on the front. Form an "X" with the 2 pieces of rope.[2]
    Advertisement
  3. When wrapping, make sure the end stays crossed over the first rope, forming an "X" as you go back around the pole, the same one you made when you crossed the ropes in the last step. Go over the pole, not under. Push it halfway around the pole, though you'll bring it to the front again in a minute.[3]
    • You should see 2 loops wrapped over the pole, making an "X" in front, the one you just created in the previous step.
  4. Bring the rope back around to the front. You should see the original loop and the loop you just made. Go under the loop you just made and pull the end out at the top.[4]
    • With this movement, you'll create a second "X."
  5. Pull on both ends of the knot to tighten it up. You may need to push the loops together on the pole if your rope isn't very flexible.[5]
  6. Advertisement


Method 2
Method 2 of 3:

Using a Clove Hitch while Climbing

PDF download Download Article
  1. Grasp the rope coming off your harness. Slip the edge of it into the carabiner clip from the left or right, depending on how the clip is facing. The long end of the rope (the one running down to your harness) should be coming out on the side away from you. [6]
    • When climbing indoors, carabiner clips are anchored in the rocks so you can tie your rope on them to act as a safety. You can use this in any climbing that uses anchors.
    • One benefit of this knot is you can tie it with one hand.
  2. Reach across to the other side of the carabiner clip where the long end of the rope is. Grab it on the side opposite the clip part of the carabiner and then twist it up on itself to make a small loop. It should look like a lowercase cursive "e."
    • The rope should come down from the clip, then go up and forward to make the loop.
  3. Bring the loop around so it goes in front of the rope on your harness. Slip it onto the carabiner clip to complete the knot.
    • The "front" of the loop should go over the clip first.
  4. This will make the knot more secure, though it can still come untied if you loosen it up. You can adjust the ends on either side of the knot as needed without untying it.
  5. Advertisement


Method 3
Method 3 of 3:

Using the Quick Method over a Loose Pole or Clip

PDF download Download Article
  1. With the end of the rope on the left, twist the rope to the left near the end to make a simple loop. Move down the rope 1 to 2 inches (2.5 to 5.1 cm) away from the end and twist the rope to the right to make a second loop.
    • You should end up with 2 loops. On the left loop, the end leading away will be in front of the other part of the loop. On the right loop, the end leading away will be behind the other part of the loop.
    • You can only use the quick method with something that has at least one end up to slip the loops over.
  2. Don't flip the loop as you move it. Simply slide it over so that it's sitting in front of the left loop. You should have 2 loops on top of each other now.
  3. If you're using a pole, slip it inside the 2 loops. You can also do this with a carabiner clip or other object. If it's too tight, use your fingers to open the loops a little.
  4. Pull on both ends of the rope to tighten it over the object. Make sure to keep tension on the knot to hold it in place.
  5. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!

Warnings

  • This knot will be secure as long as you maintain tension on it. However, it can come loose in situations where the rope is not taut.


Advertisement

About This Article

Britt Edelen
Co-authored by:
Outdoor Educator
This article was co-authored by Britt Edelen. Britt Edelen was an active member of his local Boy Scouts troop near Athens, Georgia from ages 8 to 16. As a Scout, he went on dozens of camping trips, learned and practiced many wilderness survival skills, and spent countless hours appreciating the great outdoors. In addition, Britt worked as a counselor for several summers at an adventure camp in his hometown, which allowed him to share his passion for and knowledge of the outdoors with others. This article has been viewed 291,301 times.
How helpful is this?
Co-authors: 24
Updated: August 17, 2024
Views: 291,301
Article SummaryX

Start your clove hitch knot by wrapping a rope halfway around a tree, pole, or any other vertical object, leaving a loose end that’s at least 6 inches long. Then, take the loose end, bring it over the rest of the rope to form an “X,” and wrap that end around the pole a second time. Make sure the second wrap crosses over the pole, not under it. Next, bring the loose end back around and slide it underneath the loop you just made to form another “X.” Finally, pull the ends of the rope to tighten the knot. To learn how to fasten a clove hitch to a climbing carabiner or a loose pole, keep scrolling!

Did this summary help you?

Thanks to all authors for creating a page that has been read 291,301 times.

Did this article help you?

Advertisement