How to Safely and Properly Use a Circular Saw

PDF download Download Article
Make straight, beveled, and notched cuts with this complete guide
PDF download Download Article

Using a circular saw for the first time might seem intimidating, but this tool is one of the easiest to use once you get the hang of it. Not only are they great for DIY projects, they allow you to achieve clean, precise cuts through a variety of materials. Before you begin sawing, familiarize yourself with the design features of the specific model you’re using and be sure to wear gloves and eye protection to keep yourself safe while you work. Keep reading to learn how to safely master the circular saw.

How to Use a Circular Saw: Overview

Mark your cut and clamp your material in place on the edge of a flat surface. Adjust the blade’s depth so it extends no further than ¼ in (0.64 cm) past the bottom of the material. Align the “0” mark on the baseplate with your cut mark. Squeeze the trigger to activate the saw, then slowly push through the material.

Section 1 of 6:

Making a Basic Straight Cut with a Circular Saw

PDF download Download Article
  1. Step 1 Measure and mark the cut you want to make on the material.
    Use a straight edge or ruler and a pencil or marker to draw a straight line along each area you want to cut. These lines will help you guide the blade while it’s in operation, so make sure they’re bold enough to be plainly seen.[1]
    • Rip cuts are cuts that go along the grain (usually along the longest dimension of the material), while cross cuts go against the grain (along the shorter dimension).
    • Circular saws are most often used to make straight cuts along a piece of dimensional lumber, plywood, OSB, sheet metal, or other sheet materials.
    • Circular saws can also be used for wavy or curvy cuts, however, for super complex cuts, it may be better to try out a miter saw or use a jigsaw.
  2. Step 2 Clamp your material...
    Clamp your material to a saw table or between two sawhorses. If you’re using sawhorses, space them so that the distance between them is slightly smaller than the size of your material. If you’re using a table, position the material so the area you’re cutting off is hanging off one edge.[2] Make sure the material is properly supported and free of obstructions underneath.
    • If you don’t have sawhorses or a saw table, use a strong, stable surface you don’t mind getting nicked or elevate the material with a few spare pieces of wood.
    • Try to avoid cutting your material directly on top of concrete or other hard surfaces—this can cause severe damage to both your work surface and the blade of your circular saw.
    Advertisement
  3. Step 3 Loosen the knob in the back to adjust the depth of the blade.
    Position your saw on top of the material so the saw blade hangs off one edge. Adjust the knob in the back until the ends of three teeth poke out below the material. Try not to extend your blade more than 1⁄4 in (0.64 cm) past the bottom of the material.[3]
    • Setting the blade too deep will increase the saw’s friction, which can be dangerous, wear down the teeth, and leave imperfections in the material.
    • If you’re sawing a piece of lumber that’s 1 in (2.5 cm) thick, for example, you’d set your blade no deeper than 1.25 in (3.2 cm).
  4. Step 4 Adjust the bevel angle knob for angled cuts (if needed).
    Twist the small knob on the back end of the saw counterclockwise to unlock it. Slide the knob to one of the angle presets on the frame to make custom angled (beveled) cuts. Once you’re satisfied with the angle, turn the clockwise to lock it in place.[4]
    • Make sure the locking knob is secure before you activate the saw. Otherwise, the scale may move when the blade makes contact with your material.
    • Changing the angle of the blade will allow you to make beveled cuts along squared edges or get just the right contouring on oddly-shaped pieces.
    • If you don't need an angled or beveled cut, adjust the blade so it's perpendicular to your material and lock it in place.
  5. Watermark wikiHow to Use a Circular Saw
    On the front edge of the baseplate you'll see a small notch with a bold line on either side. The line on the left hand side of this notch is labeled "0."[5] It corresponds to the position of the blade when it's set to 90 degrees, and is used any time you’re making a normal cut.[6]
    • The line labeled "45" on the right hand side of the notch is for making beveled cuts at a precise 45-degree angle.
  6. Step 6 Activate the saw blade by pulling the trigger on the rear handle.
    On some models, there may be an additional safety trigger near the top of the saw that you’ll need to flip with your thumb so the saw starts up when you pull the trigger. Once you engage the trigger, the blade will begin spinning. Wait until it gets up to full speed to begin cutting.[7]
    • If you’re right-handed, grip the rear handle with your right hand and place your left hand on the front handle for additional stability. If you’re left-handed, reverse this orientation.
    • Double-check your measurements and make sure the baseplate is properly aligned before you begin cutting.
  7. Watermark wikiHow to Use a Circular Saw
    Push the circular saw through the cut at a steady, even pace. Use both hands to maneuver the saw straight down the cut line.[8] Make sure the “0” baseplate notch stays aligned with your cut line the entire time.
    • If it feels like you need to force the blade forward to get it to cut, your blade is probably dull and needs to be replaced.
    • The blade guard will retract as you move the saw forward and lower when you lift it off of your work surface. You can also pull the lever on it to move the guard out of the way when making angled or irregular cuts.
    • Attempting to move the saw too quickly can increase the likelihood of mistakes or cause the blade to become jammed with debris.

    Safety is Essential

    Keep your hands a safe distance away from the blade at all times while the saw is in operation. If you need to make any adjustments to either the saw or your material, be sure to take your finger off the trigger completely before doing so.

  8. Step 8 Release the trigger to stop the blade after each cut.
    Once you've completed your cut, let go of the trigger and wait for the blade to come to a complete stop. To prevent potential mishaps, keep your finger off of the trigger while you review your work or line up your next cut.[9]
    • Try to avoid putting your finger on the trigger unless you're preparing to make a cut—you may activate the saw accidentally.
    9. Advertisement
Section 2 of 6:

Making Notch Cuts with a Circular Saw

PDF download Download Article
  1. Step 1 Mark both edges of the notch on the material and set the blade depth.
    Use whatever object you’re fitting in the notch as a guide for your measurements. Place the object against the material and mark both sides with a pencil or marker. Measure the depth of the object and set your sawblade accordingly.[10]
    • Make sure to clamp your material to a sawhorse or work table before you start sawing.
    • To set the depth of the blade, loosen or tighten the small knob located near the back of the motor.
    • If you’re fitting the notched material into another object, measure the length, width, and height of the object with a ruler or tape measure and mark it onto the material with a pencil or marker.
  2. Step 2 Make a series of cuts inside both marks on the material.
    Set your blade down against the side of the material, with its metal shoe on top of the surface. Squeeze the trigger on the handle and slide the blade between the marks for the notch. Pull the blade all the way through, then pass it through the material on the same side about 1⁄4 in (0.64 cm) from the previous mark.[11]
  3. Step 3 Knock out the material with a hammer and chisel.
    Use the sharp end of the hammer to break away the bits of material left inside the notch.[12] Once the large parts are cleared away, use a chisel to smooth out the bottom of the notch so your material can fit into your object smoothly.[13]
    • If you’re comfortable using the saw, you can carefully position the shoe on top of the material, pull up the guard, and run the saw side to side across the notch to clear the bottom.[14]
    4. Advertisement
Section 3 of 6:

Learning the Parts of the Circular Saw

PDF download Download Article
  1. Most circular saws have similar parts, but may be laid out differently.
    Circular saws are some of the most popular power tools for DIYers and professionals alike. Before you try to cut anything, familiarize yourself with what each part of your circular saw does.[15]
    • Handles: Hold the large handle and squeeze the trigger to turn on the blade. If your saw comes with a second handle, place your non-dominant hand on it.
    • Safety or trigger lock switch: This is on the handle, and prevents the saw from turning on if the trigger is squeezed. Press it with your thumb and squeeze the trigger to turn on the motor.
    • Blade guard: This retractable plastic cover protects you from the blade. When the saw is pushed forward from the edge of the material, the guard lifts so the blade can cut.
    • Shoe or baseplate: This is the metal base that rests on the material. They usually have measurements on the side and a notch on the front to indicate the position of the blade.
    • Bevel adjustment knob: This is the small knob or lever in a metal slide with numbers etched onto it. Twist and slide the knob up to angle your saw up to 50 degrees (some go up to 90 degrees).
    • Depth adjustment knob: This is the knob usually located next to the bevel adjustment knob. Loosen or tighten this knob to set how deep the blade goes into your material.
    • Electrical cord or battery: If you have a corded saw, there will be a cord connected to the motor. If your saw is cordless, there will be a battery by the motor instead.
Section 4 of 6:

Operating a Circular Saw Safely

PDF download Download Article
  1. Step 1 Wear gloves and...
    Wear gloves and safety glasses to keep yourself safe while you work. Handyman Lui Colmenares says “The most important thing when you use a saw is to [wear] goggles.”[16] Circular saws send debris flying that can injure your eyes. In addition, wear snug-fitting clothing and tie back long hair to prevent anything from getting caught in the moving saw blade.
    • If you’re going to be sawing for an extended period of time, consider grabbing some earmuffs as well.
    • If you have sensitive airways, strap on a dust mask or respirator to avoid inhaling sawdust.[17]
  2. Step 2 Make sure the area is clear and hold the saw until it stops spinning.
    Before using the circular saw, ensure that there are no cords, tools, or other items on top or beneath the material that the blade can make contact with. When you’re finished making a cut, hold the saw up away from the material and wait until the blade stops spinning before putting it down.[18]
    • Before making a cut, hold the trigger down to ensure that it reaches full power before pushing the saw forward through the material.
    • Secure one side of the material you’re cutting to your table or sawhorse with clamps. Try to avoid clamping both sides—this can pinch the blade and cause the saw to kick back.[19]
    • Keep both hands on the saw at all times if the saw is two-handed. If it isn’t, place your other hand safely out of the way.
  3. Step 3 Unplug the saw whenever you’re done using it.
    Confirm that the blade guard is in the down position, covering the blade. When you need to make an adjustment, change the blade, or when you’re done with the job, remove the plug from the wall outlet.[20] To store your saw, wrap the cord around the handle, and put the saw away until the next time you need it.
    • Some circular saws come with a case. If yours doesn’t, find a dry, clean area to store it in. Place it on a stable surface on its side with the blade facing away from nearby objects.
    • If you have small children at home, make sure your saw is locked up, out of reach, or otherwise inaccessible.
  4. Step 4 Inspect the saw before you cut with it.
    Inspect the blade to make sure it rotates correctly and that it’s sharp. Sharp blades work better than dull blades, and are safer. Remove off any sawdust from the air vents with a vacuum or brush and check that the housing cord, trigger, blade guard, and shoe are in good condition.[21]
    • Try to avoid removing the blade guard. If the guard makes it difficult to make a certain cut, lift the guard’s handle with one hand before starting the blade, then let it go when you’re done.
    5. Advertisement
Section 5 of 6:

Changing the Blade on a Circular Saw

PDF download Download Article
  1. Step 1 Press the button between the handle and blade and rotate the blade.
    This is the arbor-lock button, and it locks the saw blade into place inside the circular saw while you’re using it. Usually, this small button is near the top of the saw between the top handle and the upper blade guard. Hold it down as you gently turn the blade until the locking mechanism engages.[22]
    • If your saw plugs into the wall, make sure it’s unplugged before attempting to change the blade.
  2. Step 2 Use the wrench provided with your saw to loosen the blade’s nut.
    Circular saws come with a special wrench or tool you can use to loosen the arbor nut in the center of the blade so you can pull it out. Turn the wrench in the same direction that the blade turns in to unscrew and remove the nut.[23]
    • If you don’t have a tool to remove the blade, use an adjustable wrench or a socket wrench. You can also order a new one from the circular saw’s manufacturer.
    • The arbor mounts the blade onto the saw. The motor inside the saw causes the arbor to rotate, allowing the blade to spin safely.
  3. Step 3 Remove the old blade, attach the new one, and screw on the nut.
    Pull the upper blade guard’s lever. Carefully pry the blade off the arbor and remove it. Lift the lever up and slide the new blade onto the arbor, making sure the end of the saw’s teeth face the direction that the saw rotates in. Use the blade wrench to attach and tighten the arbor nut.[24]
    • Circular saws usually have an arrow on the saw’s blade guard that tells you which direction it spins.
    • If your saw has a diamond-shaped arbor that comes out with the blade, place the blade in between two wood blocks and use a hammer to gently tap it out of the center.
    • Old saw blades can usually be disposed of at a metal recycling center or scrap yard, but some local governments have their own programs. Check what’s available in your area.[25]
    • Blades with more teeth give you a cleaner cut, while those with less teeth give you rougher edges but remove material quickly, which is useful for longer rip cuts.
    4. Advertisement
Section 6 of 6:

Types of Circular Saws

PDF download Download Article
  1. Step 1 Sidewinder circular saw
    Sidewinder saws have their motors mounted in-line with the blade. They’re more compact and lightweight than worm drive saws, and their blades tend to spin faster (usually at 6,000 RPM or higher). This makes them great for cross cutting and unusual cuts.[26]
    • Sidewinder saws usually cost around $50 to $200, which makes them a popular choice for home DIYers.[27]
    • All of these saws have corded and cordless battery powered versions, but sidewinder saws are more commonly cordless.
  2. Step 2 Worm drive circular saw
    Worm drive saws are versatile but might be a bit intimidating for beginners. These saws have their motors sitting in-line with the handle and come with a narrow shoe or base, making it easier to cut in small spaces. They also have larger teeth, more power, and more durability than sidewinder saws, increasing its torque.[28]
    • However, because they’re heavier than sidewinder saws and usually require more maintenance, worm drive saws tend to be more popular with construction professionals.
    • Worm drive saws also tend to be a little more expensive, costing between $150 to $400.
  3. Step 3 Compact circular saw
    Compact circular saws are handheld saws that look like large rotary cutters. They’re lighter and more portable than worm drive or sidewinder saws, which makes them handy for smaller DIY tasks and making cuts in super tight spaces.[29]
    • They usually cost anywhere between $50 to $300.
    • Their blades usually range from around 4 to 5.5 in (10 to 14 cm).
  4. Step 4 Track saw
    These saws make splinter-free and ruler-straight cuts, which is great for jobs that require a lot of precision. Most track saws have a 6.5 in (17 cm) blade with a large blade cover to protect you. They also have a long track guide on the bottom of the shoe, which helps you create accurate and repeatable cuts.[30]
    • However, track saws tend to cut less deep than circular saws.
    • Popular for carpenters and woodworkers, the cost of these saws ranges between $300 to $550.
    5. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    Is it easy to use a circular saw?
    Lui Colmenares
    Lui Colmenares
    Licensed Contractor
    Lui Colmenares is a Licensed Home Improvement Contractor and Handyman for Mr. Handy NYC based in New York City, New York. Lui is trained and educated as an industrial engineer and specializes in carpentry, painting, and general handyman work such as mounting TVs, doorknob and deadbolt installation, furniture assembly, tile repair, and grouting. Mr. Handy NYC prides itself on quality work performed with speed, skill, and punctuality.
    Lui Colmenares
    Lui Colmenares
    Licensed Contractor
    Expert Answer
    Using a circular saw is less about how easy it is and more about being safe while using it. You've really, really got to use googles unless you're fine with potentially losing an eye.
    Thanks! We're glad this was helpful.
     Thank you for your feedback.
     If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
    Yes No
    Not Helpful 2 Helpful 2
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Tips

  • There are saws with the blade mounted on the left or the right—choose the direction that corresponds with your dominant hand.[31]
    Thanks
    Helpful 0 Not Helpful 0
  • To maintain your circular saw, inspect the cords, vents, and blades frequently. Use a vacuum or brush to clean it regularly, and replace any damaged or badly worn parts.[32]
    Thanks
    Helpful 0 Not Helpful 0
  • Place a speed square next to your saw’s baseplate to help you cut in long, straight lines.[33]
    Thanks
    Helpful 0 Not Helpful 0
Show More Tips
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Submit
Thanks for submitting a tip for review!
Advertisement

Warnings

  • Never hold your material with one hand while cutting it with the other hand. Improperly holding your materials can result in serious injury.
    Thanks
    Helpful 1 Not Helpful 0
  • Always wear work gloves and safety glasses while working with power tools.
    Thanks
    Helpful 0 Not Helpful 0
  • Check your material for nails and other obstructions that can cause your saw to kick back before using it.
    Thanks
    Helpful 0 Not Helpful 0
Advertisement

Things You’ll Need

You Might Also Like

Use a Laser CutterAn Ultimate Guide on How to Use a Laser Cutter
Set Planer Blades
How to
Set Planer Blades
Sharpen a Chainsaw
How to
Sharpen a Chainsaw Blade with a File
Measure Chainsaw Bar Length
How to
Measure Chainsaw Bar Length
Unlock a Dewalt Miter Saw
How to
Unlock a Dewalt Miter Saw
Adjust a Miter Saw
How to
Adjust a Miter Saw
Cut Angles on a Table Saw
How to
Cut Angles on a Table Saw
Use a Scroll Saw
How to
Use a Scroll Saw
Operate a Chainsaw
How to
Operate a Chainsaw
Start a Stihl Chainsaw
How to
Start a Stihl Chainsaw
Adjust Chainsaw Tension
How to
Adjust Chainsaw Tension
Clean a Chainsaw
How to
Clean a Chainsaw
Advertisement

References

  1. ↑ https://www.bhg.com/home-improvement/deck/building/how-to-measure-and-mark-lumber-for-decks/
  2. ↑ https://youtu.be/oEaB_X23ifc?t=34
  3. ↑ https://www.alce.vt.edu/content/dam/alce_vt_edu/teacher-resources/lab-safety-resources/pcircularsaw.pdf
  4. ↑ https://www.thisoldhouse.com/tools/21015868/circular-saw-101-how-to-make-an-angle-cut
  5. ↑ https://www.thisoldhouse.com/tools/21015858/circular-saw-101-how-to-use-the-sightlines
  6. ↑ https://www.outoftheww.com/projects/how-to-use-a-circular-saw
  7. ↑ https://www.ccohs.ca/oshanswers/safety_haz/power_tools/saw_circ.html
  8. ↑ https://www.outoftheww.com/projects/how-to-use-a-circular-saw
  9. ↑ https://www.dit.sa.gov.au/__data/assets/pdf_file/0017/427301/CircularSaws.pdf
  1. ↑ https://youtu.be/vq94VCPVGoo?t=8
  2. ↑ https://youtu.be/vq94VCPVGoo?t=16
  3. ↑ https://youtu.be/vq94VCPVGoo?t=20
  4. ↑ https://youtu.be/XKfe6uYIQWw?t=177
  5. ↑ https://youtu.be/vq94VCPVGoo?t=25
  6. ↑ https://www.ccohs.ca/oshanswers/safety_haz/power_tools/saw_circ.html
  7. ↑ Lui Colmenares. Licensed Contractor. Expert Interview. 18 August 2020.
  8. ↑ https://www.ccohs.ca/oshanswers/safety_haz/power_tools/saw_circ.html
  9. ↑ https://www.ccohs.ca/oshanswers/safety_haz/power_tools/saw_circ.html
  10. ↑ https://www.alce.vt.edu/content/dam/alce_vt_edu/teacher-resources/lab-safety-resources/pcircularsaw.pdf
  11. ↑ https://www.alce.vt.edu/content/dam/alce_vt_edu/teacher-resources/lab-safety-resources/pcircularsaw.pdf
  12. ↑ https://www.ccohs.ca/oshanswers/safety_haz/power_tools/saw_circ.html
  13. ↑ https://www.thisoldhouse.com/tools/21017271/how-to-change-a-circular-saw-blade
  14. ↑ https://www.thisoldhouse.com/tools/21017271/how-to-change-a-circular-saw-blade
  15. ↑ https://www.thisoldhouse.com/tools/21017271/how-to-change-a-circular-saw-blade
  16. ↑ https://www.epa.gov/recycle/how-do-i-recycle-common-recyclables
  17. ↑ https://www.protoolreviews.com/sidewinder-vs-worm-drive-circular-saws/
  18. ↑ https://www.finehomebuilding.com/1998/05/01/circular-saw-basics
  19. ↑ https://www.protoolreviews.com/sidewinder-vs-worm-drive-circular-saws/
  20. ↑ https://todayshomeowner.com/tools/guides/how-to-choose-and-use-a-circular-saw/
  21. ↑ https://www.thisoldhouse.com/tool-lab/23289446/tool-lab-how-to-select-and-use-a-track-saw
  22. ↑ https://www.thisoldhouse.com/tools/21124337/how-to-choose-and-use-a-circular-saw
  23. ↑ https://todayshomeowner.com/tools/guides/how-to-choose-and-use-a-circular-saw/
  24. ↑ https://www.thisoldhouse.com/tools/21124337/how-to-choose-and-use-a-circular-saw

About This Article

Lui Colmenares
Co-authored by:
Lui Colmenares
Licensed Contractor
This article was co-authored by Lui Colmenares and by wikiHow staff writer, Cheyenne Main. Lui Colmenares is a Licensed Home Improvement Contractor and Handyman for Mr. Handy NYC based in New York City, New York. Lui is trained and educated as an industrial engineer and specializes in carpentry, painting, and general handyman work such as mounting TVs, doorknob and deadbolt installation, furniture assembly, tile repair, and grouting. Mr. Handy NYC prides itself on quality work performed with speed, skill, and punctuality. This article has been viewed 490,699 times.
4 votes - 95%
Co-authors: 39
Updated: November 4, 2024
Views: 490,699
Categories: Manual and Power Saws
Article SummaryX

Before you use a circular saw, put on thick work gloves and safety glasses to protect yourself. Then, mark the material you want to cut and place it on a saw table or between 2 sawhorses. Next, use the central lever on the saw to set the blade so it's 1/8-1/4 inch below the bottom of your material. Once you've set the blade, position the "0" line on the baseplate over your cut line and pull the trigger on the rear handle to start the saw blade. Finally, push the saw slowly and smoothly over the surface of the material, following along the line you marked. To learn how to make beveled cuts with a circular saw, scroll down!

Did this summary help you?

In other languages
Thanks to all authors for creating a page that has been read 490,699 times.

Reader Success Stories

  • Wunna Lwin

    Wunna Lwin

    Mar 9, 2017

    "I am really thankful for this detailed guideline for operating. I am looking for training materials for my workers..." more
More reader stories Hide reader stories
Share your story
If you buy through links on our site, we may earn a commission.

Did this article help you?

Advertisement