PDF download Download Article PDF download Download Article

Uline strapping tools are used for securing heavy loads with straps and seals. Choose the strapping size and material that suits your load, then start positioning the straps. Wrap a strap around the load and use tensioning, sealing, and cutting tools to secure it in place. Once you’re done, your load should be ready for transporting!

Method 1
Method 1 of 3:

Tensioning and Sealing Polyester Strapping

PDF download Download Article
  1. Place 1 end of the strap on top of the load and keep it in place by having someone hold it or setting something heavy on top of it. Slide the other end beneath the load, then pull it up and over. With polyester strapping, the end that is closest to your body should be on the bottom.[1]
    • Adjust the straps so they run down the center of the load to keep everything in place.
  2. These pieces form the main handle on the tool. Squeezing them will lift up the gripper plate on the left side of the tool.[2]
    Advertisement
  3. Leave about 5 in (13 cm) of strapping in front so you have enough to secure later, and slide the strap up against the side of the tool. Once you have the bottom strapping in place, you can release the tension lever and base handle.[3]
    • The cutter wheel is the piece that looks like a knob on the tool’s front left side.
  4. Pushing the tension lever up will move the windlass (the middle ratcheting device on the left side of the tool) into place. The end of the strapping should go through the center line of the cutter wheel, then up through the center of the windlass.[4]
    • Once the strapping is in place, push the tension lever back and forth 2-3 times to tighten it up a bit and keep the strapping secure.
  5. Keep tightening until the strap is secure and taut around all sides of the load. The tensioner tool will ensure that you have a small amount of slack to apply the seals, so don’t worry about leaving any extra slack.[5]
    • Be careful not to over-tighten, which can damage the edges of the load and put too much strain on the strapping.
  6. Set it down with the flat side on top and the 2 bent sides tucked around the strapping. Leave about 1 to 2 in (2.5 to 5.1 cm) of the bottom strap at the front of the seal.[6]
  7. Completely open up the sealer tool and place it directly over the seal. Press hard, bringing the 2 handles together, to push the ends of the seal tightly around the strapping. Pull the handles apart and remove the sealing tool.[7]
  8. Now that the straps are secured, go back to the tensioner tool and squeeze the 2 handles together again. Keep gripping the handles and slide the tensioning tool off to the right to remove it from the strapping.[8]
    • This will activate the cutter wheel, trimming the top layer of strapping to a neat length.
  9. Advertisement
Method 2
Method 2 of 3:

Tightening and Sealing Industrial Steel Strapping

PDF download Download Article
  1. Slide the steel strapping under the load, then bring up both ends around either side. Overlap the ends, making sure that the end that is closest to your body is on top.[9]
    • Adjust the strapping to center it around the load.
  2. These pieces extend toward the back of the tool. Grip them both together to lift up the gripper on the front left side of the tool.[10]
  3. Leave about 5 in (13 cm) of excess strap at the front of the tool so you have enough strapping to secure later. Release the tension lever to let the gripper fall and hold the straps in place.[11]
  4. Keep ratcheting until you achieve the desired level of tension. The steel strapping should feel tight and secure around the load, but it should not be tight enough to cut into the edges.[12]
    • If the ratchet lever is in the upward position when you finish ratcheting, you’ll need to reposition it. Push the handle pull (located at the front of the tool) forward and gently bring the tension lever back down.
  5. The seal should sit on the strapping, flat side facing up. Adjust it until its 2 bent sides wrap around the straps. [13]
    • Leave about 3 to 4 in (7.6 to 10.2 cm) of the top strap in front of the seal to help ensure that strap won’t slip through the seal.
  6. Spread the handles of the sealing tool’s completely apart and place the nose of the tool directly over the seal. Press the handles in to meet each other, clamping the seal into place.[14]
    • This will crimp down the top of the seal and press the bent sides upward.
    • Spread the handles apart once again and remove the sealing tool.
  7. Lift the top strap up, away from the bottom strap, and use a cutter to trim off the excess. Watch out for flying pieces, since steel tends to snap off forcefully.[15]
    • Leave about 2 to 3 in (5.1 to 7.6 cm) of top strap, and throw away the trimmed end. Keeping a few inches of strap, rather than cutting right next to the seal, will help ensure it stays secure and taut.
  8. This will lift the gripper and allow you to slide the tensioner tool off to the right. Now your straps will be secure and ready to hold the load in place![16]
  9. Advertisement
Method 3
Method 3 of 3:

Choosing and Positioning Your Strapping

PDF download Download Article
  1. Polyester strapping is lighter, cheaper, safer, and easier to use than steel. It also holds the highest retained tension of any plastic strapping, making it the perfect for medium to heavy-duty loads, such as pallets, or non-compressible loads, like shipments of bricks.[17]
  2. This material works well on loads with sharp edges, such as steel or metal, and it functions best in extreme temperatures or indoor conditions, such as steel service centers, rail car applications, or boiler rooms. Choose from a variety of widths, then make sure your tools are meant to work with steel material.[18]
    • Use protective gear like thick work gloves and protective eyewear if you’re working with industrial steel strapping. This will help keep you safe if any steel strap goes flying as it’s cut.[19]
  3. The larger and heavier your load is, the wider your straps should be. Luckily, Uline offers several options for both polyester and steel. However, keep in mind that tools and seals are not interchangeable between sizes or materials, so make sure to use tools that match your strapping.[20]
    • Uline’s polyester strapping comes in 2 widths, 12 in (1.3 cm) and 58 in (1.6 cm).[21]
    • Their industrial steel strapping comes in a wider variety of sizes, including 38 in (0.95 cm), 12 in (1.3 cm), 58 in (1.6 cm), and 34 in (1.9 cm).
    • If you already own strapping, measure its width to make sure the tools you order are compatible.
  4. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Tips

Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!

Things You’ll Need

Tensioning and Sealing Polyester Strapping

  • Polyester strapping
  • Tensioner
  • Seal
  • Sealer tool
  • Gripper polypropylene seals

Tightening and Sealing Industrial Steel Strapping

  • Work gloves
  • Protective eye gear
  • Industrial steel strapping
  • Tensioner
  • Seal
  • Sealer tool
  • Cutter tool

You Might Also Like

Track a Package Without a Tracking NumberTrack a Package Without a Tracking Number
Ups Says Delivered but No PackageWhat to Do When Your UPS Package Is Missing (But Says Delivered)
Contact FedEx Contact FedEx
What Does It Mean when a Package Is in TransitWhat Does “In Transit” Mean & How Long Will It Take to Get Your Package?
Measure the Length x Width x Height of Shipping Boxes Measure a Box for Shipping
Find a USPS Tracking NumberFind a USPS Tracking Number
What Does Out for Delivery MeanWhat Does "Out for Delivery" Mean?
Ship a Package with UPSShip a Package with UPS
Ups Mail Innovations ExpeditedWhat is UPS Mail Innovations Expedited Shipping & How Does it Work?
Package Being Processed at Carrier FacilityWhat Does “Package Being Processed at Carrier Facility” Mean?
Do You Tip Furniture Delivery​​Tipping Furniture Delivery Workers: Is It the Norm?
Ship a CakeShip a Cake
Pack Picture Frames for ShippingPack Picture Frames for Shipping
Become an Authorized Shipping Outlet for UPSBecome an Authorized Shipping Outlet for UPS
Advertisement

About This Article

wikiHow Staff
Co-authored by:
wikiHow Staff Writer
This article was co-authored by wikiHow Staff. Our trained team of editors and researchers validate articles for accuracy and comprehensiveness. wikiHow's Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards. This article has been viewed 84,305 times.
14 votes - 56%
Co-authors: 6
Updated: January 2, 2023
Views: 84,305
Thanks to all authors for creating a page that has been read 84,305 times.

Did this article help you?

Advertisement