How to Use an Ammeter

Co-authored by Jesse Kuhlman

Last Updated: July 14, 2024 References

Whether you are doing diagnostics or just learning about circuits, knowing the current is an important part of electrical work. Current is the measure of the flow of electricity through a circuit in amperes (amps) by a device known as an ammeter.^{[1]
X
Research source} You can check amperage by wiring an ammeter into the circuit (also called “in-series”), or you can detect current by clamping an induction meter around a wire.

Part 1

Part 1 of 3:

Setting an In-Series Ammeter and Breaking the Circuit

Download Article

1
Set the ammeter current type and range. If your ammeter divides the range of current into settings, choose the highest setting. Next you should select the kind of current you’ll be measuring: AC (Alternating Current) or DC (Direct Current).
- Choosing the highest setting on your ammeter from the outset will prevent you from blowing the meter’s internal fuse if the amperage is too high.^{[2]
  X
  Research source}
- Battery powered circuits run on DC. Other power supplies may be AC or DC, and some can alternate between both. Check the power supply manual or label to determine its current type.^{[3]
  X
  Research source}
2
Test the internal fuse of your ammeter. This will only take you a second and it will save you some time wasted on false readings. Your ammeter should have two leads: an input (+) and an output ( - ). Hold these together with your ammeter on. If the resistance rating is low, your fuse is good.^{[4]
X
Research source}
- The resistance reading of your ammeter will be indicated on a display on the front of the meter. You may have to adjust the power range before it can read the low level of a working fuse.
- Most ammeter fuses can be easily replaced or reset, though this process will vary according to your brand and model. Consult your ammeter’s manual to learn how to fix blown fuses.
- If you adjusted the power range lower to check the fuse, reset the range to its maximum to prevent the fuse from blowing when taking the actual amperage.
Advertisement
3
Break the circuit. But before you do, make sure the power is off and all batteries are removed to prevent getting zapped. Now you need to create a break in the wiring between the negative ( - ) terminal of the power source and the power input for the item receiving power.
- The ammeter will be tied into the circuit at this break so that electricity passes through the meter on its way to the item being powered, allowing the meter to take a reading.
- You may be able to “break” your circuit by loosening the fasteners connecting wiring to the power source’s negative ( - ) terminal or at the power input for the item receiving power.
- If you can’t create a break in the circuit at the negative ( - ) terminal or power input, you can cut, strip, and then resplice the wire.

Part 2

Part 2 of 3:

Tying in an In-Series Ammeter to Take a Reading

Download Article

1
Connect the ammeter leads to the circuit. This process will depend on your model of ammeter. Essentially, the negative ( - ) end of your ammeter will connect to the power source side of the broken circuit. The positive end (+) will connect to the opposite side, so that the ammeter bridges the break.
- Most ammeters use color coding to indicate positive and negative ends of a circuit. This may be different from country to country, but in many cases, red will represent positive and black negative.^{[5]
  X
  Research source}
- The most commonly used ammeters have clamps that allow them to easily attach to wires.^{[6]
  X
  Expert Source
  
  Jesse Kuhlman
  Master Electrician, Kuhlman Electric
  
  Expert Interview. 30 June 2020.} Other models may use metal probes that you'll wrap the wire around.
- You can also simply hold the leads of your ammeter to the bare wires of the broken circuit. Prevent exposed wire from touching anything while the circuit is engaged.^{[7]
  X
  Research source}
- Be sure to only test one wire at a time.^{[8]
  X
  Expert Source
  
  Jesse Kuhlman
  Master Electrician, Kuhlman Electric
  
  Expert Interview. 30 June 2020.}
2
Restore power to the circuit and take the reading. Switch the power source back on or reinsert the batteries for the circuit. Electricity will now pass through the meter, causing it to display the amperage of the current.^{[9]
X
Research source}
- Depending on the strength of the circuit you’re testing, you may need to reduce the range for the power gauge until the display registers activity.
- Bare wires shouldn’t touch anything while the circuit is powered. Doing so could cause the circuit to short, an electrical fire, or a false reading.^{[10]
  X
  Research source}
Now that you have your reading, you can turn off power to the circuit once again. Remove the ammeter and refasten the circuit’s wiring or splice back together wire that’s been cut.^{[11]
X
Research source}

Part 3

Part 3 of 3:

Using an Induction Ammeter

Download Article

Induction ammeters are different from in-series ones in that induction units won’t have leads or probes. Instead, they’ll have a single clamp or ring through which a wire will pass. The induction sensor reads current through the electromagnetic field given off by the electricity.^{[12]
X
Research source}
2
Position the sensor around the power input wire. Locate the negative ( - ) terminal for the power source. The wire that runs between this and the item being powered is your power input line. Open the clamp and enclose it around the power input wire.
- Because of the way electricity is distributed in a circuit, if you clamp two different wires together, it will throw off the meter’s reading.^{[13]
  X
  Research source}
Setting the ammeter to auto will allow the meter to automatically adjust the range it is measuring. This will prevent you from blowing a fuse in the meter. If you need to adjust any other settings, this is the time to do it.^{[14]
X
Research source}
Depending on your model, there may be a button you need to push, like a trigger, before it starts taking a reading. Other units might take a reading as soon as they are set to auto. Unclamp the ammeter, turn it off, put it away, and you’re done.^{[15]
X
Research source}

Expert Q&A

Search

Add New Question

Question

How do you use an ammeter in a circuit?

Jesse Kuhlman
Master Electrician, Kuhlman Electric
Jesse Kuhlman is a Master Electrician and the Owner of Kuhlman Electric based in Massachusetts. Jesse specializes in all aspects of home and residential wiring, troubleshooting, generator installation, and WiFi thermostats. Jesse is also the author of four eBooks on home wiring including "Residential Electrical Troubleshooting" which covers basic electrical troubleshooting in residential homes.

Jesse Kuhlman

Master Electrician, Kuhlman Electric

Expert Answer

The most commonly-used ammeter is a clamp on style. Take the meter and clamp it around the wire you want to test. (It's important to only test one wire at a time.) Make sure the meter is set to the amp setting, then look at the display.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 1 Helpful 6