How to Waterproof Your Basement

Co-authored by Grant Wallace

Last Updated: December 3, 2024 Approved

Although basements can be extremely useful regions of your home, many of them are damp or leaky, making them unsuitable choices for any purpose. Waterproofing your interior walls is an easy solution but may not solve the problem, while waterproofing your exterior walls is more difficult but more effective. Before you start a basement remodelling project, consider the many options, such as repairing and diverting water leakage, applying concrete sealer and waterproof paint, or installing a sump pump.

Method 1

Method 1 of 3:

Applying Concrete Sealer and Waterproofing Paint

Download Article

1
Remove any salt and lime deposits from your basement walls. Salt and lime deposits are the most common reason sealing fails. Douse a damp rag with muriatic acid and scrub the walls thoroughly. Follow this by rinsing the area very liberally with a water hose, then vacuum it off the floor. This will normally take several applications. You will see the muriatic acid react with the deposits on the wall.^{[1]
X
Research source}
- Always wear gloves when handling muriatic acid. If you get any on your skin, wash it off with water immediately.
2
Apply 2 thin coats of concrete sealer with a heavy brush. Regardless of the brand you choose, every 5 gallon (19 L) bucket will cover approximately 100 square feet (9.3 m²). Select a ¹⁄₄ inch (0.64 cm) or ³⁄₈ inch (0.95 cm) roller made with tampico bristles, which are a natural fiber. Work from the bottom of the wall to the top and make sure to apply a thin coat for the best results. Apply the second coat at 90-degree angles to your first coat to allow consistent coverage.^{[2]
X
Research source}
- All concrete sealers can be used to improve concrete water resistance, although some products are better for this purpose than others. Stick with sealers that are advertised as penetrating and impregnating for the best results.
- After applying the first coat, wait 2 hours before adding the second. Refer to your specific sealant for drying times.
- Don't use a roller thicker than ³⁄₈ inch (0.95 cm) or the application will be too heavy.
- Try to apply concrete sealer before you finish your basement to avoid making a mess in a finished area.
Advertisement
3
Apply 3 thin layers of waterproof paint for small, intermittent leaks. Dip your roller into the paint 2 to 3 times. Start about 1 foot (0.30 m) from the bottom of the wall and 6 inches (15 cm) from the corner. Roll upward at a slight angle and apply a light amount of pressure. When you get 2 to 3 inches (5.1 to 7.6 cm) from the ceiling, roll up and down and move back to the corner. Keep moving from the floor to the ceiling and move about ¾ of the width of the roller so you overlap each stroke.^{[3]
X
Research source}
- Continue rolling until you paint the entire wall.
- Allow the paint to dry for at least 24 hours or according to manufacturer recommendations.

Method 2

Method 2 of 3:

Installing a Sump Pump

Download Article

1
Research the parts and function of a sump pump. The primary purpose of a sump pump is to remove water that accumulates in a sump basin. The basin is located in a basement trench that slopes downward. When water accumulates in the trench, it moves into the basin via a pipe, where it is pumped through piping that extends from the top of the basin to the outside of your home. From here, it travels down the slope away from your home.
- If your basement is unfinished, you can keep the trench filled with rocks and nothing else. But ideally, you should cover it with concrete once you finish your basement.
- Call a professional basement specialist if you're not up to conduct the installation on your own.
2
Dig a trench for your sump pump's basin. Start by creating a 16 to 18 inch (41 to 46 cm) line that runs perpendicular to the inside of the basement wall using an electric jackhammer. This will be the width of your trench that holds the sump pump basin. Now, continue removing the patch of concrete flooring of this width along the length of the wall. Now, dig your trench so it's approximately as deep as the bottom of the footing, which are the slabs of concrete directly under the walls of your home.^{[4]
X
Research source}
- Rent a jackhammer from a home improvement store and use a pointed bit for the best results. Always stand with your feet shoulder-width apart, grip the handles firmly, and hold the tip at a 45-degree angle to the ground. Press down with medium pressure and let the weight of the jackhammer do most of the work.
- Thrust the shovel straight downward and wiggle it from side to side and forward and backward to loosen the soil. Get on your knees if it's more comfortable.
3
Create a hole for the basin so that the top is flush with the concrete floor. The size of your basin will depend on your system. Typically, 30 inch (76 cm) basins are ideal for anything 120 feet (37 m) or less, 36 inch (91 cm) models are best for systems over 120 feet (37 m), and 2 basins are used for drains longer than 180 feet (55 m). Continue digging downward with your shovel and don't worry if it's a bit bigger than your basin—you can fill it with soil later.^{[5]
X
Research source}
- Make sure that the top of the hole for the basin is flush with the concrete floor.
4
Lay down 4 inch (10 cm) Schedule 10 perforated irrigation pipe onto rock. Place down rocks to create a slope down to the basin at least ¹⁄₄ inch (0.64 cm) for each 10 feet (3.0 m). Before laying down the pipe, make sure that the holes are facing down. This slope will bring the water through the irrigation piping to the basin.
- Don't use rocks smaller than washed river rock—they're prone to getting clogged with sediments and minerals.
- Purchase a pipe that contains rows of ¹⁄₂ inch (1.3 cm) perforation holes on just one side of the pipe.
- Attach PVC elbows at the corners afterward.
5
Cut the drain pipe holes in your basin using a reciprocating saw. Use a permanent marker to designate the region where the irrigation pipe meets the basin. For the top hole where the pipe leaves the basin, use the pre-determined guide. Be sure to have someone hold the basin for you while you cut to keep it steady. Hold the blade perpendicular to the basin along a point of the circle and gently press the trigger. Don't worry if the holes aren't perfect.^{[6]
X
Research source}
- As you cut through the basin, keep your blade speed steady, never cut too fast, and remember that more pressure means faster blade cuts.
- If the flat "knockout" areas that pre-mark pipe holes don't work for your space, don't use them.
- Never create holes in the bottom of the basin—water can rise from the bottom.
6
Connect the irrigation pipe to the sump pump basin. Start by laying down the piping onto the sloped rocks. Now, press the male end of the pipe into the hole in the basin about 4 inches (10 cm). Adjust the slope with rocks as necessary as you connect the piping.^{[7]
X
Research source}
- Fill the space surrounding the piping with river rock up to the concrete.
7
Lay plastic over the rocks and piping and top them with concrete mix. Make sure that the plastic is at least 6-mil thickness to provide an adequate vapor barrier. Pour the concrete into a wheelbarrow and gently tilt it to apply it onto the plastic. Level the concrete with a 3 foot (0.91 m) piece of 2x4 wood after by sliding it along the surface until it is level with the floor.^{[8]
X
Research source}
- Purchase bagged concrete mix that is designed for sidewalks and slabs.
- Use the hand float to fill any gaps under existing walls.
8
Locate the spot to drill between the rim joists on the inside and outside. This is where the sump pump diverts water to the outside. From the inside, find a clear, undamaged spot between the rim joists, which are the horizontal pieces of wood that provide lateral support for the vertical joists of your floor's frame. After locating it inside, find the corresponding spot on the outside and make sure it's on a downward slope.
- Make sure you have enough PVC piping to run from the sump pump to your rim joists and outside of your home.
- Be sure the slope outside your home is at least 2 inches (5.1 cm) for every foot that you move away from the foundation. Always start by adding dirt within a foot of the foundation and make sure the dirt is always 6 inches (15 cm) below the sill plate. Move outward from your home in one foot increments until the slope is 2 inches (5.1 cm) per foot.
9
Create a hole between the rim joists using a hole saw. Connect a 2 inch (5.1 cm) drill bit to your hole saw. Grab the drill and turn it on before it touches the surface. As it starts turning, apply firm pressure horizontally into the hole location.^{[9]
X
Research source}
- Don't press too hard and maintain even pressure for the best results.
- Check that your PVC piping fits through the hole. If it's too small, drill it a bit larger until it's an adequate size.
10
Drill a ¹⁄₄ to ³⁄₈ inch (0.64 to 0.95 cm) hole into 6 to 8 inches (15 to 20 cm) of PVC piping. Place the PVC piping vertically onto a flat surface and face downward with a standard metal drill. Angle the drill bit upward at 45 degrees before you turn the drill on and apply firm pressure. The angle ensures that water sprays downward while the pump works, giving it time to increase its speed gradually before it attempts to force the check valve—which closes to prevent liquid from flowing backward—open.^{[10]
X
Research source}
- Use metal or wood drill bits, as both work for PVC.
- Purchase electric drills from home hardware stores.
11
Attach the PVC piping to the pump and connect a check valve on top. Insert the PVC piping with the hole into the pump, ensuring that the hole faces downward. Afterward, attach your check valve. Be sure that the check valve does not interfere with the pump switch, which protrudes from the pump and is connected to the dangling oval float.
- Don't glue the piping into the valve just yet.
12
Connect another section of PVC that reaches the basin's top. The second section of PVC must run from the check valve to the top of the basin. From here, it will connect to piping that exits the basement.
- After connecting the second section of PVC, take one more look at the check valve position and make sure it doesn't interfere with the pump switch.
13
Connect PVC piping between the sump pump outlet and your home's rim joist hole. Check the manufacturer's instructions to determine the appropriate sized piping—most use 1.5 inch (3.8 cm) diameter PVC piping. Start by dry fitting your piping from the sump pump to the hole. After making sure everything fits properly, apply caulk between the seams the seal everything up.^{[11]
X
Research source}
- Apply caulk to seal the PVC piping after everything is in place. Place the nozzle onto the sealing rim and apply steady, gentle pressure to the trigger. Remember that less is more—you can always do a second run.

Method 3

Method 3 of 3:

Repairing and Diverting Water Leakage

Download Article

1
Add dirt against your home's foundation to create a slope. You must ensure that the ground next to your foundation slopes away from your home, not towards it. But backfilled dirt around the foundation will typically settle lower than the surrounding dirt and cause the ground to sink in and slope towards your house. Add dirt up against the foundation to create a drop of at least 2 inches (5.1 cm) for every foot that you move away from the foundation.
- Make sure that the top of the dirt is at least 6 inches (15 cm) below the sill plate, which is the bottom horizontal piece of the building. This will ensure that there is no ground contact that promotes the rot of building materials.
- Start by adding dirt within a foot of the foundation, taking care to ensure that it's always 6 inches (15 cm) below the sill plate. From here, move outward in one foot increments until you create a slope of 2 inches (5.1 cm) for every foot.
2
Clean your gutters and check that downspouts are working. Always clean your gutters 2 times a year—once in spring and once in fall. Start at the downspout and use a garden trowel or your hands to remove large chunks of dirt. In addition, be sure that the downspouts are discharging water at least 5 feet (1.5 m) away from the foundation of your home.^{[12]
X
Research source}
- Work horizontally from your ladder and move down the gutter.
- If your home doesn't have gutters, consider installing some or hiring a contractor to do so. This will ensure that water is properly diverted from your home.
3
Remove plants that are fewer than 12 inches (30 cm) from the foundation. Watch out for shrubs and other plants that are too close to your foundation. Rotted roots can create a path for surface water to flow down to your foundation. Use a shovel to dig in a circle around the roots of each plant—cut through as many of them as you can! Afterward, insert the shovel underneath the roots as far as possible and lever the plant out of the soil.^{[13]
X
Research source}
- If you plant anything new, always try to plant them on the slope around your home to direct water away from your foundation.
- Destroy as many of the roots as possible to prevent regrowth.

Community Q&A

Search

Add New Question

Question

Can Dry Lock, or a similar product, be used over painted block walls?

Community Answer

This is not recommended. Dry Lock, and other similar products, will only be as strong as the first coat of paint applied. For best results, Dry Lock needs to be applied to a clean, unpainted block or brick wall.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 17 Helpful 39
Question

I'm digging out the side of my basement due to water damage. Once it's dug out, what is the best water sealer to use?

Andy Orr

Community Answer

It depends on the foundation material, but plastic-based paint, either brushed on or professionally spray-applied is always a safe bet. It runs about $50 a gallon.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 5 Helpful 12
Question

If the walls are already painted, what should I use to seal them?

Community Answer

I would use a concrete-based paint on top of the existing paint; clearly the existing paint isn't stopping the leak.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 9 Helpful 14

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Things You'll Need

Applying Concrete Sealer and Waterproofing Paint

Damp rag
Concrete sealer
Roller with tampico bristles
Gloves
Waterproof paint

Installing a Sump Pump

Safety goggles
Steel-toed boots
Respirator
Electric jackhammer
Shovel
5 gallon (19 L) buckets or rubber feed buckets
Reciprocating saw
Hammer drill with a carbide-tipped masonry bit
Rake
Washed river rocks
4 inch (10 cm) Schedule 10 perforated irrigation pipe
1 inch (2.5 cm) irrigation piping
6-mil thick plastic
2x4 wood
Sump pump
PVC piping
Circular drill
Caulking gun
Caulk

Repairing and Diverting Water Leakage

Soil
Garden trowel
Gloves
Shovel

Tips

Before beginning a serious basement remodelling project, observe your basement carefully during heavy rainstorms. If you can last a year of weather without any water leaks, you're probably going to be OK in the future, but only if you keep your gutters clean and take care of your foundation!

Thanks
Helpful 1 Not Helpful 1
When installing a sump pump, be sure to refer to local plumbing codes. Most installations will require a one-way valve to prevent water from coming into the sump through the outlet.

Thanks
Helpful 0 Not Helpful 2
Drill 1 inch (2.5 cm) holes into the block cores of your basement walls if they're concrete. Afterward, connect 1 inch (2.5 cm) irrigation piping into the blocks. This isn't necessary, but beneficial as it promotes the flow of this water into the drain.

Thanks
Helpful 0 Not Helpful 0

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Always wear eye protection and a mask or respirator while cutting concrete.

Thanks
Helpful 31 Not Helpful 28
Mold can be a serious health risk. Keeping your basement dry with a dehumidifier can help.

Thanks
Helpful 0 Not Helpful 0