PDF download Download Article
Steps for installing sensors for different kinds of lights
PDF download Download Article

A light sensor is a great solution if someone in your household tends to leave certain lights on. This is easily achieved by replacing any existing light switch with a motion sensor light switch. You could also install a brand new LED light and motion sensor somewhere like an unfinished basement or garage. Keep in mind that if you don’t have any experience with electrical wiring, you should contract a licensed electrician to perform this job for you so you don’t cause any accidents.

Method 1
Method 1 of 2:

Installing a Light Switch Sensor for an Existing Light

PDF download Download Article
  1. Flip the breaker that supplies electricity to the room where you plan to install the light switch sensor. Test the lights in the room to make sure they are really cut off from power.[1]
    • Never start installing a light sensor or performing other electrical work without shutting off the power first.
    • Use this method when you want to install a light sensor in a finished room that already has a light connected to a switch, such as a bedroom, living room, bathroom, or hallway, for example.
  2. Use a screwdriver to take out the screws if it has any, then pull it off the wall and set it aside. Pop it off the light switch by sliding something flat and skinny under an edge and prying it off the wall if it doesn’t have any screws.
    Advertisement
  3. Use a screwdriver to remove the 2 screws that attach the light switch to the electrical box in the wall. Disconnect the wires by twisting off any plastic wire nuts or unwrapping any electrical tape and untwisting the wires if they are twisted together. Pull the light switch out of the wall and set it aside.[2]
    • Some light switches might have screws on the backside that hold the wires from the walls in place. If this is the case, use a screwdriver to loosen them until you can detach the wires.
    • Plastic wire nuts are cone-shaped plastic caps that screw onto a set of wires to keep them connected. Your light sensor might come with them or you can buy them separately at a hardware store or online.
  4. Twist the hot black wires together and screw a plastic wire nut onto the ends. Repeat this for the neutral white wires and red load wires.[3]
    • The live and neutral wires are always black and white, respectively.
    • The load wire is the wire that connects to the light fixture. It might be a different color than red in your wall, such as black. It usually comes out of the top of the electrical box in the wall, since it is coming down from the ceiling. However, you can only be sure which wire it is if you test all the wires with a multimeter.

    Warning: If you aren’t sure which wires are which in your wall, do not attempt to complete the wiring yourself. Call a licensed electrician so they can come test the wires for you.

  5. Twist them together and cover them with a plastic wire nut. These are the ground wires.[4]
    • The ground wire in your wall will always be bare copper.
  6. Tuck all the wires into the electrical box in the wall. Screw the light sensor onto the wall using the provided screws and a screwdriver or electric drill. Snap the wall faceplate into place.[5]
    • You can leave the faceplate off until after you test the light if you want.
  7. Flip the breaker that supplies electricity to the room back on at the main fuse box. Flip the power switch on the light switch sensor to the ON position to check if it turns the light on, then set it to the AUTO position. Go out of the room until the light turns off, then walk back in to see if the light turns on automatically.[6]
    • Read the light switch sensor’s owner’s manual for any instructions about how to adjust the timing and sensitivity for your specific light sensor. Some models allow you to make the sensor more or less sensitive, adjust how long it keeps the light on, or even change the dimness of the light.
  8. Advertisement
Method 2
Method 2 of 2:

Connecting a Sensor to an LED Light

PDF download Download Article
  1. Flip off the main power breaker so that there is no electricity being supplied while you work. Test a light switch or outlet where you plan to install the motion sensor to ensure that there is no electricity flowing to the area.[7]
    • Always do this first before you perform any kind of electrical work.
    • This method is a good option if you want to install a motion sensor light in an unfinished room like a basement or garage. It doesn’t make sense to do it in a finished room where you could more easily install a light switch sensor.
  2. Install 2 junction boxes with wire connections on a ceiling or wall. Screw 2 junction boxes onto a wall or ceiling and connect them to the power supply. Run a wire for connecting the light sensor to the LED light between the 2 boxes.[8]
    • If you have an existing light that you want to connect a light sensor to, like an outdoor light or a light bulb with no switch, you can just swap the whole light for a fixture with a built-in motion sensor.
    • You could install more than 2 junction boxes and wire them all to the box for the motion sensor if you want to connect more than 1 light to the sensor.

    Warning: If you don’t have any experience with electrical work, hire a licensed electrician to install junction boxes and connect them to the power supply. It is not safe to try and do this yourself unless you know exactly what you’re doing. An electrician can also easily install the motion sensor and LED light for you at the same time.

  3. Twist the exposed metal ends of the black wires from the motion sensor and the junction box together and screw a plastic wire nut onto them to hold them together. Repeat this for the white wires.[9]
    • Your motion sensor might have different colored wires, such as a brown wire instead of a black wire. If so, refer to the manufacturer’s instructions to be sure which wire is the live wire.
    • Some motion sensors have an easy-to-read wiring diagram on the back that shows you which wires to connect.
    • The neutral wire on the motion sensor can also be blue or green instead of white.
  4. Hold the exposed metal end of the motion sensor’s red wire together with the end of the black live wire that goes to the other junction box for your LED light. Put a plastic wire nut on top of the ends to hold them together.[10]
    • This will make your motion sensor function as the light switch for your LED light.
  5. Twist the end of the motion sensor’s copper ground wire together with the end of the junction box’s copper ground wire. Twist a wire nut over the ends to secure them together.[11]
  6. Tuck all the wires up into the junction box. Screw the motion sensor in place using the provided screws and a screwdriver or power drill.[12]
    • Depending on the specific model of motion sensor, there might be a mounting bracket that you have to install first or it might just screw directly onto the junction box.
  7. Connect the colored wires from the junction box to the matching colors of wires on the back of the LED light fixture using plastic wire nuts. Screw the LED light fixture into place on the junction box using the provided hardware and a screwdriver or power drill.[13]
    • You can use any kind of LED light fixture for this. For example, if you are installing a motion sensor light somewhere like a basement with low clearance, you could use a low-profile, flush-mount LED light.
  8. Switch the power breaker back on at the main fuse box. Walk by the motion sensor to check that it turns on the light.[14]
    • If you used an adjustable light fixture of some type, you can now adjust it so the light hits exactly where you want it to.
  9. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    How do you install an outdoor motion sensor light?
    Mike Garcia
    Mike Garcia
    Licensed Landscape Contractor
    Mike Garcia is a Licensed Landscape Contractor and the Founder of Enviroscape LA, a full-service landscape design and construction firm in Los Angeles, California. With over 30 years of experience, Mike specializes in sustainable landscape practices. Mike holds an Ornamental Horticulture degree, C-27 Landscape Contractor and D-49 Tree Service Contractor licenses, and Permaculture Design, California Naturalist, International Certified Professional Pond Contractor, and Pond Building certifications. He is one of eight Internationally Certified Pond Builders in the world. Enviroscape LA has won landscape and water feature awards from the International Professional Pond Contractors Association (IPPCA), National Association of Pond Professionals (NAPP), and the California Landscape Contractors Association (CLCA). Mike is a past president of the CLCA and currently serves on their local Board of Directors. Enviroscape LA has been featured in PONDS USA Magazine, Pond and Garden Lifestyles Magazine, and the Los Angeles Times. Mike has appeared on Extreme Home Makeover, HGTV's Landscapers Challenge, and A & E's series Fix That Yard.
    Mike Garcia
    Licensed Landscape Contractor
    Expert Answer
    Typically, outdoor motion sensor lights are hardwired to a house, so you need a high voltage source for that. Screw the unit into a wall, and connect the hot wire, the common wire, and the ground wire. After those three are connected, screw the whole unit into the house. Once the light is properly installed, lights will go on when the area gets dark and something disturbs the motion sensor.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Tips

  • If you want to install a motion sensor on an existing outdoor light or another light fixture without a switch, you can just replace the light fixture with one that has a built-in motion sensor.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Warnings

  • Always turn off the power supply before you start any kind of electrical work.
  • If you are not experienced or comfortable performing electrical wiring on your own, hire a licensed electrician to do it for you to avoid accidents.
Advertisement

Things You’ll Need

Installing a Light Switch Sensor for an Existing Light

  • Light switch sensor
  • Screwdriver
  • Wire nuts
  • Electric drill (optional)

Connecting a Sensor to an LED Light

  • 2 junction boxes with wires
  • Motion sensor
  • LED light
  • Wire nuts
  • Screwdriver or power drill

You Might Also Like

Advertisement

About This Article

Mike Garcia
Co-authored by:
Licensed Landscape Contractor
This article was co-authored by Mike Garcia. Mike Garcia is a Licensed Landscape Contractor and the Founder of Enviroscape LA, a full-service landscape design and construction firm in Los Angeles, California. With over 30 years of experience, Mike specializes in sustainable landscape practices. Mike holds an Ornamental Horticulture degree, C-27 Landscape Contractor and D-49 Tree Service Contractor licenses, and Permaculture Design, California Naturalist, International Certified Professional Pond Contractor, and Pond Building certifications. He is one of eight Internationally Certified Pond Builders in the world. Enviroscape LA has won landscape and water feature awards from the International Professional Pond Contractors Association (IPPCA), National Association of Pond Professionals (NAPP), and the California Landscape Contractors Association (CLCA). Mike is a past president of the CLCA and currently serves on their local Board of Directors. Enviroscape LA has been featured in PONDS USA Magazine, Pond and Garden Lifestyles Magazine, and the Los Angeles Times. Mike has appeared on Extreme Home Makeover, HGTV's Landscapers Challenge, and A & E's series Fix That Yard. This article has been viewed 66,742 times.
10 votes - 20%
Co-authors: 4
Updated: August 23, 2022
Views: 66,742
Categories: DIY
Thanks to all authors for creating a page that has been read 66,742 times.

Did this article help you?

Advertisement