How to Change Headlight Bulb on a Chevrolet Silverado

Reviewed by Jason Shackelford

Last Updated: June 2, 2021 References

This set of instructions will show you how to change a headlight bulb on the 1999-2007 Chevrolet Silverado, the GMC Sierra, the Suburban 99-06, and the Yukon/Tahoe of the same years. Different models will vary.

Part 1

Part 1 of 2:

Removing the Old Bulb

Download Article

1
Ensure your vehicle is parked on a level surface in a well-lit area. Set the emergency brake and release the hood by pulling the lever located at the far left side of the driver’s footwell.
- Check to ensure the headlights and the key switch are both off.
Open the hood by inserting your hand in the gap between hood and grill. Locate the lever assembly, and slide leftward slightly. You should be able to lift the hood fully upward.^{[1]
X
Research source}

Advertisement
4
Locate two (2) dowel pins on top of the headlamp assembly. Rotate the headlamp retainer pins until they are free of the headlamp housing.
- If the pins are difficult to dislodge from road dirt, the flat blade screwdriver may be useful. Insert between headlight housing and pin, and twist gently to dislodge pin.
Make sure to note which location the pin came from, as they are not interchangeable.
6
Grasp headlight assembly and pull gently towards you.
- Do not pull quickly. There is a wiring harness connected to the back that is easily damaged.
7
While holding the headlamp housing, disconnect the harness from the bulbs by squeezing the connector and pulling it straight away from the bulb.^{[2]
X
Research source}
- This can be difficult; sometimes it can be useful to set the housing on a stand while you do this.
8
Take the headlamp housing, now free of wiring harness, to a workbench or some stable surface.
- Ensure the surface you are working on is soft enough to not mar the headlamp surface.
^{[3]
X
Research source}

Part 2

Part 2 of 2:

Installing the New Bulb

Download Article

1
Take your new bulb out of the packaging.
- Do not touch the glass part of the bulb with your fingers. The oil on your fingers will cause the bulb to prematurely fail. Handle bulb with clean gloves only.
^{[4]
X
Research source}
4
Reconnect harness to new bulbs.
- You should hear an audible “click” as the connector fully seats. Tug slightly on the connection to ensure the harness is connected fully.
5
Loosely place the housing to the vehicle. Make sure you haven’t trapped or pinched any wires. Try to loosely line up the pin holes.
- If it doesn’t seem to be lining up, take two steps back and look at it. You should be able to see what side isn’t correct.
6
Reinsert pins through vehicle body and headlight housing. Make sure they are in the same position they came from.
- If you have them mixed up, shorter one goes closer to center of vehicle.
Turn headlamps on, and return to front of vehicle.^{[5]
X
Research source}

Community Q&A

Search

Add New Question

Question

Does my whole light have to be replaced, or can I just change the bulb?

Community Answer

It depends on the situation. If your light isn't working, it is most likely the bulb that just needs to be replaced. If that doesn't work, check that there is power running to the bulb by checking the socket with a multi-meter. If it reads that there is no voltage, then the problem is with the housing unit of the light instead of the bulb.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 0 Helpful 2

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

If the bulb burns out again quickly, check that you haven’t touched the glass part, and your housing has maintained a good seal and isn’t letting in water.

Thanks
Helpful 2 Not Helpful 0
If both headlights burn out simultaneously, check your headlight switch and wiring. Suspect an electrical fault.

Thanks
Helpful 0 Not Helpful 0