How to Check a Start Capacitor

Co-authored by Daniel Stoescu and Hunter Rising

Last Updated: September 3, 2024 Fact Checked

Start capacitors are used in many home appliances, like washers, refrigerators, or air conditioners. If your appliances are humming but not starting or performing correctly, check the capacitor to see if it’s working properly. By conducting a simple test with a multimeter, you can easily tell if your capacitor is still working or if it needs to be replaced.

Part 1

Part 1 of 2:

Discharging the Capacitor

Download Article

1
Locate the capacitor inside your appliance. Capacitors are metal tubes that store an electric charge usually found near a motor in the appliance. Use a screwdriver to open your machine and locate the capacitor. Use needle-nose pliers with an insulated handle to remove wires.^{[1]
X
Research source}
- Make sure your device is unplugged and turned off before you find the capacitor.
2
Use a screwdriver with an insulated handle. Find or purchase the screwdriver from a hardware store. The rubber will prevent electricity from traveling through the metal to your hand.^{[2]
X
Research source}
- Use caution when working with electricity. A strong enough shock can cause serious harm or death.
- Make sure the screwdriver’s handle doesn’t have any cracks and that no bit of metal is sticking out the back. This could carry voltage and cause you serious harm.
Advertisement
3
Wear a pair of gloves meant for housework or working with electricity. Since you’re using an insulated screwdriver, work gloves will work fine. For added protection against electricity, use tight-gripping gloves made with rubber.^{[3]
X
Research source}
- Gloves can be purchased at your local hardware or home improvement store.
- Don’t use large rubber gloves because they will give you less dexterity while you’re working.
Have a firm grip on the handle, making sure you aren’t in contact with the metal. Even with gloves, the current running through the shaft can cause you harm.^{[4]
X
Research source}
5
Place the shaft of the screwdriver on the positive terminal. Set the screwdriver down so the terminal contacts the shaft 1 inch (2.5 cm) from the tip. The correct terminal will be marked with a plus sign (+). Make sure the screwdriver doesn’t touch the other terminal on the capacitor yet. ^{[5]
X
Research source}
- On a capacitor with more than 2 terminals, the positive terminal may be labeled “common” instead.
6
Tap the negative terminal with the tip of the screwdriver. While maintaining contact with the positive terminal, tilt the screwdriver so you make contact with the negative terminal. Once you make the connection, you’ll hear a small pop and see a spark on the tip of the screwdriver. Don’t be alarmed; this is the capacitor discharging completely.^{[6]
X
Research source}
- Do not hold onto the metal part of the screwdriver while making the connection. Capacitors can store a lot of energy and the resulting spark or current can result in serious injury.
After the initial spark, keep the screwdriver on the terminals and tap the negative side with the tip 1 or 2 more times. Sometimes, leftover charge is still left in the capacitor.^{[7]
X
Research source}

Part 2

Part 2 of 2:

Using a Multimeter

Download Article

1
Use the capacitance setting on a digital multimeter. Multimeters are electronic devices that read the voltage and capacitance of circuits or batteries. Find a multimeter with a dedicated capacitance setting for the most accurate readings.^{[8]
X
Research source}
- Make sure the capacitor you’re testing is completely discharged or the circuit is off before using a multimeter. Too high of a voltage can damage the meter or cause you harm.
- Digital multimeters can be purchased hardware or home improvement stores.
- Capacitance is measured in farads (F).
2
Place the red probe on the positive terminal and the black probe on the negative. Hold the probes by their base without touching the metal pins on the end. Once both probes come into contact with the terminals on your capacitor, the readout on your multimeter will start to change. ^{[9]
X
Research source}
- Wear gloves while testing with a multimeter if you’re worried about any residual charge.
3
Hold the probes in place until the numbers stop changing. The numbers will fluctuate for a few seconds after you connect the terminals if the capacitor is good. Wait until the readout has the same number for 5 seconds before disconnecting the probes.^{[10]
X
Research source}
- Write down the capacitance number after you take a measurement so you can remember it.
- If the numbers do not move at all, the capacitor is considered open and needs to be replaced.
4
Ensure the reading matches the range of numbers on the capacitor. The minimum and maximum capacitance are listed on the side of the capacitor with all of its other information. The acceptable range depends on the size of the capacitor you have. If the capacitor is above or below the range, it will have to be replaced.^{[11]
X
Research source}
- If the capacitance number went up infinitely to the limit of your multimeter, the capacitor has shorted out and should be replaced.
- Some capacitors will have a set capacitance with an acceptable percentage of variance. For example, if your capacitor says “50 ±5%,” the acceptable capacitance range is 47.5 to 52.5 F.

Community Q&A

Search

Add New Question

Question

How do I tell if my capacitor is faulty?

wikiHow Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.

wikiHow Staff Editor

Staff Answer

The capacitor may have a bulge on top if it's faulty. Otherwise, when you're checking the capacitor with a multimeter, the readings will be far above or below the listed range on the unit.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 6 Helpful 14
Question

How do i check a start capacitor if my A/C is starting on the heat setting and shutting off after a few minutes?

wikiHow Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.

wikiHow Staff Editor

Staff Answer

Remove the start capacitor from the AC unit and look for a bulge on the top of the capacitor. Otherwise, use a multimeter to check.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 6 Helpful 10
Question

How can I tell the high and low parts of a capacitor?

Community Answer

You can use a DMM for this purpose. Connect the probes to the terminals of the charged capacitor. If the reading shows a minus sign then you've connected the positive probe to the negative terminal of the capacitor.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 17 Helpful 24

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Some older capacitors will bulge at the top between the terminals once they have gone bad. Visually inspect your start capacitor for a small protuberance.^{[12]
X
Research source}

Thanks
Helpful 0 Not Helpful 0
When using a multimeter to test a capacitor, always consult the capacitor’s manual as each make and model could work differently.

Thanks
Helpful 0 Not Helpful 0

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Make sure the screwdriver you use doesn’t have cracks in the handle or exposed metal coming out of the back side.

Thanks
Helpful 5 Not Helpful 0
Never touch the terminals of a capacitor with your bare hands in case it has a charge. Treat every capacitor as if it had voltage.^{[13]
X
Research source}

Thanks
Helpful 0 Not Helpful 0