PDF download Download Article PDF download Download Article

Capacitors are found in a number of electrical appliances and pieces of electronic equipment. They store excess electrical energy during power surges and discharge it during power lulls to provide the appliance with a constant, even supply of electricity. Before working on an appliance or electronic device, you must first discharge its capacitor. It’s often safe to discharge a capacitor using a common insulated screwdriver; however, it is usually a good idea to put together a capacitor discharge tool and use that for electronics with larger capacitors such as household appliances. Start by checking for a charge in your capacitor, then choose a method to discharge it if needed.

Part 1
Part 1 of 3:

Checking for a Charge

PDF download Download Article
  1. If the capacitor isn’t already removed from whatever you’re working on, ensure you’ve disconnected any power source leading to it. This usually means unplugging the electronic device from the wall outlet or disconnecting the battery in your car.[1]
    • In a car, locate your battery in the engine bay or trunk, then loosen the nuts holding the cables on the negative (-) and positive (+) terminals using an open-ended wrench or socket with a ratchet. Slide the cable off of the terminal to disconnect it. Wrap the end of each cable with a rag so they don’t touch anything.
    • In your house, you can usually unplug the device you’re working on from the wall, but if you are unable to do so, locate the house’s breaker box and flip the switch that controls the flow of electricity to the room you’re working in.
  2. Set your multimeter to its highest DC voltage setting. Different multimeters will have different maximum voltage ratings. Turn the dial in the center of your multimeter to the highest voltage setting it will permit.
    • Setting it to the highest possible setting will ensure you get an accurate reading of however many volts of electricity the capacitor is charged with.
    Advertisement
  3. The capacitor will have two posts sticking out of the top. Simply touch the red lead from the multimeter to one post and then the black lead to another post. Hold the leads on the posts while you read the display on the multimeter.[2]
    • You may need to open your appliance or remove components to gain access to the capacitor. Refer to an application specific repair manual for help if you can’t locate or access the capacitor.
    • Touching both leads to the same post will not produce an accurate reading.
    • It doesn’t matter which lead you touch to which post because it’s reading the level of current passing from one to the other.
  4. Depending on what you’re working on, the multimeter may give you a reading that ranges from single digit voltage to hundreds of volts. Generally speaking, a charge of greater than 10 volts is considered dangerous enough to shock you.
    • If the capacitor reads as having fewer than 10 volts, you don’t need to discharge it.
    • If the capacitor reads anywhere between 10 and 99 volts, discharge it with a screwdriver.
    • If the capacitor reads in the hundreds of volts, the safest way to discharge it is with a discharge tool, rather than a screwdriver.
  5. Advertisement
Part 2
Part 2 of 3:

Discharging with a Screwdriver

PDF download Download Article
  1. A charged capacitor can be very dangerous, so it’s important that you avoid coming into contact with the terminals at all times. Never touch the capacitor anywhere but on the sides of its body.[3]
    • If you touch the two posts, or accidentally connect them with a tool, you could get badly shocked or burned.
  2. Insulated screwdrivers usually have rubber or plastic handles, which creates a barrier between your hand and the metal portion of the screwdriver itself. If you don’t have an insulated screwdriver, purchase one that clearly states that it’s insulated on the packaging. Many will even tell you what voltage rating they are insulated against.[4]
    • If you are unsure whether or not your screwdriver is insulated, it’s best just to buy a new one.
    • You can purchase insulated screwdrivers at any auto part or hardware store, as well as at most large retail stores.
    • It does not matter if the screwdriver is a flat head or Phillips head.
  3. Do not use any screwdriver with a tear, crack or break in the rubber or plastic of the handle. That damage could allow the flow of electricity to pass up into your hand when discharging the capacitor.[5]
    • Purchase a new insulated screwdriver if the handle on yours is damaged.
    • You don’t have to throw a screwdriver with a damaged handle away, just don’t use it to discharge capacitors or do other electrical work.
  4. You need to maintain total control over the capacitor while you discharge it, so pick it up low on the cylindrical body with your non-dominant hand. When you pick it up, make a “C” with your hand and fingers to grip it, keeping all of your fingers away from the top where the posts are.[6]
    • Maintain a comfortable grip. There’s no reason to squeeze the capacitor too hard.
    • Keep your grip low on the capacitor to avoid contact with sparks when you discharge it.
    • Use a pair of insulated pliers to hold smaller capacitors so you don’t accidentally shock yourself while you’re discharging it.
  5. Hold the capacitor upright with the posts pointed toward the ceiling, then bring the screwdriver over with the other hand and touch it to both posts at once to discharge the capacitor.[7]
    • You will hear and see the electric discharge in the form of a spark.
    • Make sure the screwdriver is touching both terminals at once or else it won’t work.
  6. Before you handle the capacitor freely, pull the screwdriver away and bring it down again onto the two posts to see if it produces any spark. If you properly discharged it, there should be no additional discharge.[8]
    • This step is just a safety precaution.
    • Once you’ve confirmed that the capacitor is discharged, it’s safe to handle.
    • You can also confirm that it has been discharged using your multimeter if you’d prefer.
  7. Advertisement
Part 3
Part 3 of 3:

Making and Using a Capacitor Discharge Tool

PDF download Download Article
  1. A discharge tool is really just a resistor and a bit of wire to connect it to the posts on the capacitor. You can purchase all of these parts at your local auto parts or hardware store.[9]
    • The alligator clips make it much easier to keep the tool connected once it’s completed.
    • You will also need electric tape or heat shrink wrap and a soldering iron if you don’t already have one.
  2. The exact length of the wire isn’t particularly important, as long as there’s enough slack to connect both to the capacitor and the resistor. For most applications, 6 inches (15 cm) is enough, but you can make yours longer if it helps with your specific situation.[10]
    • Each wire just needs to be long enough to connect one end of the resistor to one post on the capacitor.
    • Cutting the pieces a little longer gives you some extra slack to work with and may make things easier.
  3. Use wire strippers to remove the insulation without damaging the wire inside. If you don’t have strippers, you can use a knife or razor blade to cut through just the insulation and then use your fingers to pull it off the wire.[11]
    • Both ends of both wires should show bare metal now.
    • Make sure to remove enough insulation to solder the stripped ends to other wires or clips.
  4. Solder one end of each wire to the two probes sticking out of the resistor. The resistor has a wire post sticking out of each end. Wrap the end of one wire around the first post and then solder it into place. Then wrap one end of the other wire around the other post and solder it into place.[12]
    • It should now look like a resistor with long wires sticking out of each end.
    • Leave the loose ends of each wire free for now.
  5. Cover the solder using the electrical tape by simply wrapping a piece around it. This will help hold the connection in place while also insulating it from anything that may come into contact with it. If you’re making a tool you will likely reuse, slide a tube of electrical heat shrink wrap over the end of the wire and slide it along until it covers the soldered connection.[13]
    • If you use heat shrink wrap, you can shrink the wrap in place over the connection by exposing it to the flame from a lighter or match.
    • Do not expose electrical tape to a flame.
  6. Take the loose end of one of the wires and solder an insulated alligator clip to it, then either heat shrink wrap it or cover it in electrical tape. Then do the same with the other loose end on the other wire.[14]
    • If you are going to use heat shrink wrap, remember to slide it over the wire before soldering the clip into place; otherwise, you won’t be able to get it over the head of the clip once it’s permanently affixed to the wire.
  7. Clip the end of each wire to a different terminal on the capacitor. It will discharge very quickly, though you shouldn’t see or hear a spark as you would with a screwdriver.[15]
    • Be sure each clip has a clean connection with the metal of the post.
    • Be careful not to touch the posts with your hands while you connect them.
  8. Once again set the multimeter to its highest voltage rating and touch each lead to a separate post on the capacitor. If it still shows stored voltage, check the connections on your discharge tool and try again. You can leave the multimeter connected to the capacitor while you watch the voltage drop in real time.[16]
    • If the voltage doesn’t drop, one of the connections isn’t right in the discharge tool. Examine it closely for where one might be broken.
    • Once all of the connections on the discharge tool are good, try again and it should discharge.
  9. Advertisement

Expert Q&A

Search
Add New Question
  • Question
    Can I discharge a capacitor in my microwave using just two wires connected to something else if I don't have a resistor? Will it discharge safely if I just have one wire connect to each terminal?
    Ralph Childers
    Ralph Childers
    Electrical Professional
    Ralph Childers is a master electrician based in the Portland, Oregon area with over 30 years of conducting and teaching electrical work. Ralph received his B.S. in Electrical Engineering from the University of Louisiana at Lafayette and holds an Oregon Journeyman Electrical License as well as electrician licenses in Louisiana and Texas.
    Ralph Childers
    Electrical Professional
    Expert Answer
    You can discharge a capacitor with an insulated wire, that has been stripped on each end, by touching the two terminals as you would with a screwdriver. How safe it depends on the voltage; above 100V should be done with a discharge tool.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Video

Tips

  • Do not hold the resistor in your hands, use a test lead or wire.
  • Capacitors will discharge on their own over time and most are likely to be discharged after a few days so long as no external power or internal battery is charging them -- but assume they are charged unless you have confirmed that they are discharged.
  • Once the capacitor is discharged, keep its leads connected with a resistor or piece of wire to keep it discharged.
Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

Warnings

  • Always be careful when working with electricity.
  • Large capacitors are extremely dangerous and others are often in the vicinity of the one you might attempt to work on. Working with them probably isn't best for a typical hobbyist.
Advertisement

Things You'll Need

  • Multimeter
  • Insulated screwdriver
  • Spool of wire
  • 2 alligator clips
  • Soldering iron
  • 20k OHM 5 watt resistor


About This Article

Ralph Childers
Co-authored by:
Electrical Professional
This article was co-authored by Ralph Childers. Ralph Childers is a master electrician based in the Portland, Oregon area with over 30 years of conducting and teaching electrical work. Ralph received his B.S. in Electrical Engineering from the University of Louisiana at Lafayette and holds an Oregon Journeyman Electrical License as well as electrician licenses in Louisiana and Texas. This article has been viewed 858,777 times.
170 votes - 91%
Co-authors: 19
Updated: December 19, 2024
Views: 858,777
Article SummaryX

To discharge a capacitor, it's important that you keep your hands clear of the terminals at all times or you could get badly shocked. Also, make sure you're using an insulated screwdriver that has no signs of damage on the handle. When you're ready, start by gripping the capacitor low on the base with one hand. Then, lay the screwdriver across both terminals to discharge the capacitor. To test if the capacitor discharged properly, touch both terminals at the same time with the screwdriver again. If there's no spark, the capacitor is discharged. To learn how to make and use a capacitor discharge tool, scroll down!

Did this summary help you?

Thanks to all authors for creating a page that has been read 858,777 times.

Reader Success Stories

  • Eddie H.

    Eddie H.

    Jun 7, 2023

    "I have a small compressor which has stopped working. I've stripped it down and discovered it has a capacitor..." more
Share your story

Did this article help you?

Advertisement