How to Configure Master and Slave in BIOS for Two Hard Disk Drives in a Single System

Written by Jack Lloyd

Last Updated: May 15, 2024 Tested

This wikiHow teaches you how to determine which of your Windows computer's two hard drives is the primary and which is the secondary. In order to configure master and slave settings for hard drives, your computer's motherboard must support multiple internal hard drives and you must have the second hard drive installed. "Master" drives typically store the operating system, while "Slave" drives are used for additional storage and backup.

Quick Guide: Master/Slave Hard Drive Configuration

After connecting the second hard drive, reboot the PC into the BIOS, and locate the hard drives or " Master" and "Slave" options. Set one hard drive to Master, and the other to Slave. Save your changes and reboot your PC.

Steps

Download Article

1
Make sure that your second hard drive is attached. Before you can determine which hard drive is the "Master" and which is the "Slave", you'll need to have both drives attached to your computer. While the "Master" drive is usually your computer's built-in hard drive, the second one must be attached manually to your computer's motherboard.
- If you haven't yet done so, you'll need to install the hard drive before proceeding.
Click the Windows logo in the bottom-left corner of the screen.

Advertisement
It's in the lower-left side of the Start window.
This option is at the top of the pop-up menu. Your computer will begin to restart.
5
Begin repeatedly tapping the BIOS key. The BIOS key varies from computer to computer, but is usually one of the "F" keys (e.g., F2), the Delete key, or the Esc key. You'll need to press the BIOS key before your computer's startup screen appears.
- You may receive a prompt at the bottom of the screen right before the startup screen that says "Press [key] to enter setup" or something similar.
- If you miss the BIOS window, you'll need to restart your computer and try again.
- Consult your computer's manual or online documentation to determine the BIOS key for your model of computer.
6
Enter the password if prompted. Once you reach the BIOS, you may be asked to enter a password if you set one previously. If so, type in the password and press ↵ Enter.
- If you don't remember your BIOS password, you may be able to reset it.
At the top of the BIOS screen, there should be several tabs. You can navigate through these tabs by using the arrow keys. Scroll through the tabs and examine each tab's information until you find a list of hard drives (or "Hard Disks") that are included in the computer.
This will most likely be the top hard drive in the list, though you should confirm by looking at the drive's name.
9
Change the hard drive to "Master" status. With the hard drive selected, press the "Configure" or "Change" key (usually ↵ Enter) as listed in the key legend that's at the bottom or side of the screen. You should see "Master" pop up next to the hard drive's name.^{[1]
X
Research source}
- In some cases, you may have to select None to the right of the hard drive's name before pressing the "Configure" key.
- You can also set this drive to "Auto" instead to allow your operating system to select "Master" for it.
Using the arrow keys, find and select the hard drive that you attached to the computer.
11
Change the hard drive to "Slave" status. You'll use the "Configure" or "Change" key to do this as well. Once you see "Slave" to the right (or near) the drive's name, you can proceed.
- If you chose "Auto" for the first drive, you'll instead set the second hard drive to "Auto" as well.
12
Save your changes and exit the BIOS. To do so, look for the "Save" or "Save and Exit" key in the key legend. Pressing this key will save your "Master" and "Slave" preferences and exit the BIOS.
- In some cases, you may have to press another key after saving to confirm that you want to save and exit.

Community Q&A

Search

Add New Question

Question

How do I reboot my computer?

Community Answer

Hard shut it off by pressing the power button, then pressing the power button again once it is off. Or, go into your start menu, then press the on/off/shut down or similar symbols. Choose the restart option.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 2 Helpful 2
Question

How do I slave a hard disk?

Bill Taylor

Community Answer

Assuming you are not using something antiquated that can be strapped (jumpered), the quickest way to reverse the order of the hard drives in the BIOS is to swap the cables, either on the back of the drives or on the motherboard. Otherwise, if it is nothing more than wanting to default to what you refer to as the slave on start up, simply change the boot order in the BIOS.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 1 Helpful 6

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Your computer's "Slave" drive is perfect for backing up data from the "Master" drive.^{[2]
X
Research source}

Thanks
Helpful 0 Not Helpful 0

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

When adjusting internal components in a computer, be sure to ground yourself before touching any sensitive objects such as connectors or circuit boards.

Thanks
Helpful 0 Not Helpful 0
Each computer's BIOS is slightly different than other computers' BIOS layouts. You may need to consult your computer's documentation to determine the location of the "Master"/"Slave" section.

Thanks
Helpful 0 Not Helpful 0