How to Ground Yourself to Avoid Destroying a Computer with Electrostatic Discharge

Expert guide for grounding yourself before working on a computer

Co-authored by Luigi Oppido and Jack Lloyd

Last Updated: May 12, 2024 Fact Checked

Want to make repairs or add parts to your PC without worrying that you'll short out a vital component? Grounding yourself is an easy way to avoid damaging your computer's delicate internal parts with electrostatic discharge (static electricity). This wikiHow article will walk you through the safest way to open your computer and show you how to de-static yourself with several grounding methods.

Part 1

Part 1 of 2:

Preparing Your Work Surface

Download Article

1
Work on a hard surface. Assemble or take apart computers on a clean, hard surface to minimize static buildup. A table, countertop, or a plank of wood will work fine.^{[1]
X
Expert Source

Luigi Oppido
Computer & Tech Specialist

Expert Interview. 13 November 2020.}
- Your computer should never be placed on a surface such as carpet, a blanket, or a towel when performing any action that requires you to ground yourself.
2
Stand on a hard floor in bare feet. Carpets and socks can give you a charge. Stand in bare feet on wood, tile, or other hard floors instead.
- If you don't have the option of not standing on carpet, you'll need to be especially proactive about grounding yourself once every couple of minutes.
- You can wear rubber slippers to completely block your connection to the floor, but this is excessive for home projects.^{[2]
  X
  Expert Source
  
  Luigi Oppido
  Computer & Tech Specialist
  
  Expert Interview. 13 November 2020.}
- Any shoe with rubber soles should also be enough to block your connection to the floor.
Advertisement
3
Take off all static-friendly clothing. Wool and some synthetic fabrics are especially good at gathering static, so remove these if possible and replace them with cotton clothing.
- If possible, wash and dry your clothes using a dryer sheet to minimize static build-up before working on your computer.
4
Humidify in dry weather. Static electricity is a much bigger risk in dry environments. Run a humidifier if you happen to have one, but don't bother buying one if not. The other precautions should be more than enough on their own.
- You can also humidify by hanging wet cloth in front of a radiator or fan.
All new computer components should stay in the antistatic bags they were sold in until ready for installation.

Part 2

Part 2 of 2:

Grounding Yourself

Download Article

To prevent built-up static from transferring from you to a sensitive computer component, you'll need to discharge the static into something more durable. In most cases, this is a metal item that is either touching the floor or touching a series of items leading to the floor.
2
Use your computer's case to ground yourself. Most builders use this technique: before touching or installing something that can be harmed by ESD (e.g., the motherboard), place your hand on an unpainted metal piece of the computer's case.
- You can even lay your non-dominant arm on the metal part of the case while installing the component if you want to be positive that ESD won't harm it.
3
Touch grounded metal objects every couple of minutes. This must be unpainted metal with a clear ground path, such as a metal radiator or the bay shielding on your computer's case. This is the quick and easy option, and many people build computers without taking any other precautions.
- There's a small but definite risk that this will not be enough. Rely on this only if your project is quick and the components are not valuable.
4
Ground yourself with an anti-static wristband. These cheap items are sold at electronics stores and in online markets. Wear the wristband tight against your skin, and clip the dangling end onto a grounded, unpainted metal object such as a screw.^{[3]
X
Expert Source

Luigi Oppido
Computer & Tech Specialist

Expert Interview. 13 November 2020.}
- Do not use a wireless wristband, as these do not work.^{[4]
  X
  Research source}
- If you get a wristband with a loop (rather than a clip), it's easy to slip it over the center screw on a wall outlet plate. This is supposed to be grounded (at least in US code), but you may want to double-check with a multimeter.
A common technique for keeping oneself grounded is tying a conductive wire, such as copper, around one's toe or wrist and then tying the other end around a grounded, unpainted metal object. This is ideal if you have the materials on-hand and don't have a way to work on a hard surface.
6
Work on an ESD mat. Buy an ESD mat rated for "conductive" or "dissipative", then place the computer parts on the ESD mat and touch the mat as you work. Some models will have a place to clip your wristband onto as well.
- Go with a vinyl ESD mat for computer repair; rubber is more expensive and not necessary for this purpose.
- Unless you value your peace of mind highly, this is above and beyond for most home projects.

Expert Q&A

Search

Add New Question

Question

How can I permanently ground myself to avoid electric shock?

Luigi Oppido
Computer & Tech Specialist
Luigi Oppido is the Owner and Operator of Pleasure Point Computers in Santa Cruz, California. Luigi has over 25 years of experience in general computer repair, data recovery, virus removal, and upgrades. He is also the host of the Computer Man Show! broadcasted on KSQD covering central California for over two years.

Luigi Oppido

Computer & Tech Specialist

Expert Answer

There are these grounding strips you can buy that go around your wrist that will basically make it impossible to cause an electric shock. That's going to be overkill for most people, but if you work with computer components, that's probably the best way to do it.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 5 Helpful 25
Question

What kind of surface is best for working on a computer?

Luigi Oppido
Computer & Tech Specialist
Luigi Oppido is the Owner and Operator of Pleasure Point Computers in Santa Cruz, California. Luigi has over 25 years of experience in general computer repair, data recovery, virus removal, and upgrades. He is also the host of the Computer Man Show! broadcasted on KSQD covering central California for over two years.

Luigi Oppido

Computer & Tech Specialist

Expert Answer

Hardwood or concrete is going to be good. Carpeting is going to be the worst option. If you're on a hard surface, make sure it's unpainted. Paint can often make it difficult to stay grounded.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 3 Helpful 17
Question

Can you move around when you're working on a computer?

Luigi Oppido
Computer & Tech Specialist
Luigi Oppido is the Owner and Operator of Pleasure Point Computers in Santa Cruz, California. Luigi has over 25 years of experience in general computer repair, data recovery, virus removal, and upgrades. He is also the host of the Computer Man Show! broadcasted on KSQD covering central California for over two years.

Luigi Oppido

Computer & Tech Specialist

Expert Answer

No, I really wouldn't do much walking or shuffling. Whenever I'm working on a computer, I make a conscious effort to keep my feet planted so that I'm not walking, shuffling, or dragging my feet.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 4 Helpful 22

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

When handling the CPU, hold it by the edge only. Do not touch any exposed pins, circuitry, or the metal top unless absolutely necessary.^{[5]
X
Research source}

Thanks
Helpful 0 Not Helpful 0
Damaging a computer with ESD isn't nearly the concern it was a decade ago. While it's important to take steps to prevent accidental discharge, most modern computer components have plenty of built-in shielding to prevent damage from something as simple as static electricity.^{[6]
X
Research source}

Thanks
Helpful 0 Not Helpful 0

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Even if you don't notice electrostatic discharge during assembly, small transfers of current could damage your components, lowering their lifespan. In the (rare) worst case scenario, a strong shock can permanently destroy your motherboard.

Thanks
Helpful 12 Not Helpful 1