PDF download Download Article
Troubleshoot your no-start condition with this simple guide
PDF download Download Article

If you’re trying to turn your vehicle on but nothing happens or you run into problems with your key and ignition, your ignition switch may be to blame. But how can you actually confirm that the ignition switch is at fault? What if your battery is just dead or the key isn’t working? We’ll help you confirm the problem. Read on to learn how to test your switch, narrow down the problem, and fix it so you can get back on the road in no time.

Things You Should Know

  • Use a multimeter to test the starter’s solenoid and the battery connection.
  • Inspect the fuse connected to your ignition switch to ensure that the ignition relay isn’t busted.
  • Try starting the car with your spare key and jumping the battery to rule out the obvious culprits.

Get Car Support Solve Any Problem

wH
Hi there! Do you have a question about how to diagnose or fix a problem with your car? I’ve read the manual so you don’t have to. Select your make, model, and year, then ask away!
*
*
Section 1 of 4:

Multimeter Testing

PDF download Download Article
  1. This process is unique to your vehicle’s make and model, so refer to your instruction manual for help. Typically, you’ll use a flathead screwdriver or pry bar to gently force several panels open around the wheel. Sometimes, you’ll need to remove screws, first. Jot down the order you remove the panels so you can reassemble everything in the opposite order when you’re done.[1]
    • Some dashboard panels have clips that you have to depress or tabs that you press on to release them.
  2. Set the multimeter to the 20 DC voltage setting. Turn the dial to the “V” or “Ω” to set the multimeter to the voltage configuration. Most vehicles have a 12-volt battery. The 20-volt setting is the closest you can normally get to the 12-volt range.[2]
    • Plug the black probe into the black port labelled “negative” and the red probe into the red port labelled “positive.”
    Advertisement
  3. Put the black probe on any exposed, unpainted metal surface in your vehicle. Then, look for a gold or silver terminal on the side of your ignition module. Hold the positive probe against the terminal to test the ignition switch.[3]
    • There are usually 2 terminals (B and S). One is for your battery and the other is for your ignition switch solenoid. Test both. You probably won’t get a reading from one of them.
    • Some ignition switches have 5 terminals. On these switches, test the B and L terminals in the run position, the B and S in the start position, and the G, M, and L terminals in the off position.
  4. Any reading around the 11- to 13-volt range indicates that your ignition switch is working perfectly fine, which means the problem is elsewhere. If you get a really low reading or nothing and you know the battery is working, it’s time to replace the ignition switch.[4]
    • If you don’t get a reading on any of the terminals but you can still start the vehicle, your multimeter isn’t configured correctly or you’re testing the wrong part of your starter.
    • Take your vehicle to a mechanic to get the ignition switch replaced.
  5. Advertisement
Section 2 of 4:

Fuse Check

PDF download Download Article
  1. The fuse box is usually located under the hood of your vehicle near the steering wheel. In some vehicles, the fuse box is located in the glovebox. You may need to refer to your vehicle’s manual to find your fuse box. Pop the hood and remove the cover of the fuse box.[5]
    • Here, you’re going to check the fuse for your ignition switch relay. The relay is responsible for regulating the electricity running from your battery to the ignition, so if it isn’t working properly, it can cause ignition issues.
  2. If the fuses aren’t labelled, refer to an instruction manual for your make and model to find which fuse is connected to the ignition switch. With the vehicle off, physically remove the fuse from its port.[6]
    • It should pop right out, but you may need to jiggle the fuse a bit to completely remove it.
  3. Look inside the fuse at the little piece of metal. If it is visibly burnt up and damaged, the fuse needs to be replaced. If it looks okay, test the pins with a multimeter. If you get a resistance of 50-120 ohms (Ω), the fuse is fine. If it’s too low or high, the ignition relay fuse needs to be replaced.[7]
    • You can also test the ignition relay by swapping the fuse out for a fuse that you know is undamaged and then starting the vehicle. If the vehicle starts, your old fuse was bad.
    • To replace the fuse, purchase a replacement for your specific make and model. It shouldn’t be more than $5-10 online.
  4. Advertisement
Section 3 of 4:

Symptoms of a Bad Ignition Switch

PDF download Download Article
  1. If you physically cannot turn the key, your ignition module may need to be replaced entirely. Alternatively, if you can turn the key but the engine doesn’t do anything, that’s a sign the relay or the switch need to be replaced.
    • If you can get the car running, your vehicle may randomly stall while you’re driving.
    • If you hear a clicking sound when you crank the engine but nothing else, it’s a sign your starter solenoid specifically needs to be replaced.
  2. Your key should fit tightly inside of the ignition. If it feels loose or like there isn’t anything holding the key in place, either your ignition switch is damaged or you need to replace your key.
  3. When your car has been running for a few minutes, it’s normal for your key to get a little warm. The ignition module itself shouldn’t get hot to the touch, though. If the area around the key is scalding hot, it’s a sign the electrical components in the switch aren’t working properly.[8]
    • It’s especially common for Hondas, KIAs, and other foreign cars to leave your key a little warm. It still shouldn’t be burning hot, though.
    • The problem here might be the solenoid on your ignition switch.
  4. If your dash lights up like a Christmas tree when you turn the vehicle on or your “accessory” position isn’t turning any electronics on, your ignition switch may need to be replaced. The switch basically tells your vehicle’s battery “the vehicle needs power” so if it’s going bad, your electronics may now work correctly.[9]
  5. Advertisement
Section 4 of 4:

Troubleshooting Other Problems

PDF download Download Article
  1. It’s possible that your ignition switch and starter are totally fine and your key simply isn’t working correctly. The metal ridges may have been worn down a bit and don’t fit the ignition anymore. Alternatively, the anti-theft electronic component may have died or been damaged and now it’s keeping the vehicle from starting. Test a spare key to confirm this isn’t the problem.
    • If the key does turn out to be the issue, go to a dealership and have them cut a new key for you.
    • Do you notice any tiny shards of metal near your ignition? If so, your key is getting worn down
  2. It happens to the best of us—you forget to shut off an interior light or turn the headlights off and you accidentally drain your battery. Before you start disassembling your dashboard or breaking out the fancy electrical testing gear, try turning the key to the accessory position and flipping the headlights on. If the dash lights and headlights come on, it’s not your battery.
    • If you want to be totally sure the battery isn’t to blame, try jumping the vehicle to see if it starts.
    • You can also test the battery terminals with a multimeter if you want to check it that way.
  3. Advertisement

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
Advertisement

Tips

  • If your car starts but the engine misfires when it runs and it feels like you’re getting really bad fuel mileage, you’ve probably got a bad spark plug. The spark plugs sit inside of your engine’s cylinders and provide the spark to ignite the air and gasoline. Try changing your spark plugs to see if the problem goes away.[10]
  • Once the ignition switch fires, the electrical signal travels to your ignition coil, which is where voltage is released to help the spark plugs fire. If you check the ignition switch, fuse, and the spark plugs, this is the most likely point of failure. Try changing your ignition coil to see if your problems disappear.[11]


Submit a Tip
All tip submissions are carefully reviewed before being published
Name
Please provide your name and last initial
Thanks for submitting a tip for review!
Advertisement

You Might Also Like

Reset Traction Control Light Reset a Traction Control Light (TCS)
Reset Steering Angle Sensor Without Scanner Reset Your Steering Angle Sensor Without an OBD-2
Bypass Limp Mode Get Out of Limp Mode: 5 Ways to Bypass, Signs, & More
Stop Vehicle Leave Engine Running"Stop Vehicle Leave Engine Running" Mercedes-Benz Warning: Causes & Fixes
Fix a Locked Steering WheelFix a Locked Steering Wheel
Anti Theft System Won't Let My Car StartWhat to Do If Your Car’s Anti-Theft System Prevents It from Starting
Change an Oxygen SensorChange an Oxygen Sensor
Reset Maintenance LightQuick and Easy Steps to Reset the Maintenance Required Light
Open a Hood with a Broken LatchOpen a Hood with a Broken Latch
Reset Gas Gauge Needle Reset a Gas Gauge Needle
Fix a Cigarette Lighter in a CarFix a Cigarette Lighter in a Car
Open the Hood of a Vehicle Unlock the Hood of Your Car
What Transmission Do I Have Identify Your Vehicle’s Transmission
Determine Gear RatioDetermine Gear Ratio
Advertisement

Expert Interview

Thanks for reading our article! If you’d like to learn more about ignition switches, check out our in-depth interview with Jason Shackelford.

About This Article

Jason Shackelford
Co-authored by:
Auto Technician
This article was co-authored by Jason Shackelford and by wikiHow staff writer, Eric McClure. Jason Shackelford is the Owner of Stingray Auto Repair, a family owned and operated auto repair shop with locations in Seattle and Redmond, Washington. He has over 24 years of experience in auto repair and services, and every single technician on Jason’s team has more than 10 years of experience. This article has been viewed 50,123 times.
16 votes - 73%
Co-authors: 4
Updated: December 22, 2024
Views: 50,123
Thanks to all authors for creating a page that has been read 50,123 times.

Did this article help you?

Advertisement