How to Quickly and Easily Unclog a Toilet

Clogged toilet troubling you? Plunging your way out of the situation is often the fastest and most efficient fix. Don't have a plunger? No worries! We interviewed a talented plumber, James Schuelke, who showed us many ingenious ways to unclog a toilet without a plunger too.

How to to Unclog a Toilet

If you don't have a plunger, move a toilet brush back and forth inside the porthole to remove clogs. Or, pour 1 cup of baking soda and 2 cups of vinegar into the toilet followed by 1/2 gallon of hot water. Let the mixture sit overnight. In the morning, the bowl should have drained and you can flush the toilet as usual.

Section 1 of 11:

Plunging the Toilet

Download Article

1
Insert the plunger into the toilet bowl. Make sure the plunger completely covers the hole.^{[1]
X
Trustworthy Source

Consumer Reports
Nonprofit organization dedicated to consumer advocacy and product testing

Go to source} Submerge the plunger fully in the water so that you can push and pull water through the opening, not air.
- Add water from the bathroom sink to the bowl if there isn’t enough water to cover the plunger.
- Running the plunger under hot water can soften it, which can help it create a better seal.
- Hopefully your plunger has an “extension flange.” This is the rubber extension after the bell-shaped part of your plunger and it’s designed to better fit the toilet opening.
2
Pump the plunger over the hole. Push down gently at first, since the first plunge will push air into the bowl and could splash back. Then pull up sharply to disturb the clog and loosen it. Continue vigorously pushing and pulling until the water begins to drain.^{[2]
X
Research source} It may take 15 to 20 cycles before the toilet unclogs.
- Be patient. As long as you don't have a hard object (like a kid's toy) stuck in there, plunging alone often suffices. It might not work immediately but will often work after a few dozen plunge cycles.
Advertisement
3
Flush the toilet to check the drainage. If the plunging eventually drains the bowl, but the clog is still blocking a free flow down the drain, leave the plunger in the bowl and fill the bowl with water again. Fill it to the point it is normally after a regular flush, then plunge again. Stubborn clogs might require you to do this a number of times.^{[3]
X
Trustworthy Source

Consumer Reports
Nonprofit organization dedicated to consumer advocacy and product testing

Go to source}
- Flush the toilet 2-4 times once you’re done plunging to move the blockage through the sewer system.^{[4]
  X
  Research source}

Section 2 of 11:

Using a Toilet Brush (Plumber Recommendation)

Download Article

Do your best to get the toilet brush to cover the porthole of the toilet.
3
Move the brush back and forth inside of the porthole, as you would a plunger.
- According to James, it helps if there is some water in the bowl.

Section 3 of 11:

Using an Unclogging Product

Download Article

1
Purchase an enzyme waste removal product. Look for a product that contains a mixture of enzymes that liquify waste materials. These enzymes are used in septic systems to break down waste.^{[5]
X
Research source}
- Products of this sort can usually be purchased at home improvement stores in or near the plumbing aisle. Enzyme waste removal is preferable to using a drain-clearing chemical because it will not harm your pipes or the environment.^{[6]
  X
  Research source}
- This method will only work on organic waste, not toys or other objects.
Pour the recommended amount of the enzyme product into the toilet bowl. You will typically be instructed to wait overnight for the enzymes to go to work on the clog.^{[7]
X
Trustworthy Source

Consumer Reports
Nonprofit organization dedicated to consumer advocacy and product testing

Go to source} The toilet should drain once the clog has cleared.

Section 4 of 11:

Making a Drain Cleaner

Download Article

Maybe you don’t have a plunger or the idea of plunging a clogged toilet with waste in it has you squeamish. If so, you should consider a homemade drain cleaner.

If your toilet tends to clog easily as the result of trying to flush too much waste, using a combination of hot water, baking soda and vinegar will often do the job as well as a commercial drain cleaner.

This method works better for clogs from waste and not clogs caused by hard obstructions like a toy and requires more time than plunging. Here’s how to do it:

1
Heat half a gallon of water. Boil half a gallon of water, then let it cool for a moment while you add other ingredients to the toilet bowl.
- Use at least half a gallon. A small amount of water won't work, since it won't have enough force to push through the clog.
- The water should be no hotter than a hot tea you can drink comfortably. It should not be boiling, since very hot water can crack porcelain. You want to raise the temperature of the water passing around or pressing on the clog.
2
Pour 1 cup baking soda and 2 cups vinegar into the toilet. The baking soda and vinegar create a chemical process that help to dissolve clogs. Distilled white vinegar is commonly used, but any type of vinegar will work. The mixture will fizz a great deal.
- If you don't have baking soda and vinegar on hand, try adding a few squirts of dish soap to the toilet bowl. The soap may help to loosen the clog.
- This method isn't likely to work for clogs caused by a hard obstruction, such as a toy.
Pour it from waist level, rather than right near the rim. The force of the water falling into the bowl can help to clear the clog.
In the morning, the water should have drained. This homemade drain cleaner should successfully clear clogs caused by organic material. If the water won't flush on your second try, you may have hard obstruction causing the clog. Try using a wire coat hanger or a drain snake.

Section 5 of 11:

Making a Wire Coat Hanger Snake

Download Article

Then wrap the end of the wire with a rag. Use duct tape to keep the rag in place. This will prevent the sharp end from damaging the porcelain in your toilet. The wire hanger method will generally work only if there is an obstruction in the first few inches of the drain.^{[8]
X
Research source}
2
Stick the wrapped end of the wire into the drain. Once the wire is in the drain, twist it, push it, and maneuver it in a circular motion to clear the drain. If you can feel the obstruction, push against it. Keep going until the water begins to drain.^{[9]
X
Research source}
- Make sure you're wearing rubber gloves as you do this. You may get splashed as you move the wire around.
- If you can't feel an obstruction, and the toilet won't drain, the clog must be out of reach of the hanger. Try the plumbing snake method to clear it.
The obstruction and dirty water should now be able to flow through the drain like normal. If the toilet is still slow to drain, the obstruction may have gotten pushed further back, out of reach of the hanger. In this case you'll need to use a plumbing snake to clear it.^{[10]
X
Research source}

Section 6 of 11:

Using a Plumbing Snake

Download Article

If the above methods aren’t working, it’s time to step it up with the use of a real plumbing snake.

A plumbing snake (also sometimes called a "flexible cleaning tool" or "auger") is a flexible coil of wire that can "snake" through the curves of a drain and get deeper than a wire can. The best snake is a "closet auger" which is designed specifically to clear toilet clogs without damaging or staining the bowl.^{[11]
X
Research source}
Push down, feeding the snake further into the drain until you feel an obstruction.
3
Twist and push the snake through the obstruction. The goal is to break up the obstruction into smaller pieces that can move through the pipes. It may take a few minutes of maneuvering to clear the obstruction. Once the water drains, flush the toilet to see whether it drains as quickly as normal.^{[12]
X
Research source}
- Crank the handle on an auger to push the wire through the clog.
It may become necessary to remove the toilet and run the snake through in the opposite direction. This is especially true with hard obstructions that may have been flushed by a curious child. If the obstruction is known to be hard and you are not comfortable removing and replacing the toilet, contact a plumber.

Section 7 of 11:

Utilizing a Wet/Dry Vacuum

Download Article

If you have tried plunging and snaking to no avail, consider using a wet/dry vacuum. Do not use an ordinary vacuum cleaner––it must be the wet/dry variety that can cope with water.
The bowl must be free of water and any other debris in order to vacuum out the obstruction.
Push it into the toilet bowl a few inches into the hole. Use just the flexible hose, rather than an attachment. Coil an old towel around the hole to create a seal around the drain. There’s a good chance the vacuum can suck out the clog.

Section 8 of 11:

Using a Chemical Drain Cleaner

Download Article

Another option to consider is using chemical drain cleaners. They are easy to use and widely available, but there are some things to consider before use. Many of these drain cleaners are toxic to humans and damaging to the environment.^{[13]
X
Research source}^{[14]
X
Research source}

If the drain cleaner is not successful at removing the clog, you now have a toilet bowl full of toxic chemicals. This would limit your ability to plunge the toilet safely as these chemicals can splash up at you and cause harm. Here’s how to use this method:

1
Purchase a chemical drain cleaner. They're available at most grocery, hardware, and "big box" stores.
- Only use chemical drain cleaners that are specifically made for toilets. Using other drain cleaners may damage your toilet.
- If you suspect that there is a hard obstruction, like a toy, do not use a chemical solution. Instead, use a snake or call a plumber.
- Never mix different chemical cleaners together as the result could be extremely dangerous or even fatal fumes.
2
Pour the specified amount into the toilet. Be sure you follow the manufacturer's instructions. Keep the lid down to prevent toxic fumes from filling your bathroom.
- Make sure the bathroom is well ventilated, so you won't inhale potentially dangerous chemicals.

Section 9 of 11:

Clean Up Tips

Download Article

- A used plunger (especially flange plungers) may still have water inside of it after plunging. Keep it over the toilet, turn it a bit, and shake it slightly to drain it so it won't drip on the floor.
- Disinfect the toilet bowl with a disinfectant cleaner after you've cleared the clog.
- Dispose of the wire (if used) and disinfect or dispose of the rubber gloves and any other tools (such as a plunger or snake) that you used. These tools can spread germs and start to stink if not properly cleaned.
- It’s best to mop and clean your bathroom after plunging a toilet. Even if you didn’t see and splash back out of the bowl.

Section 10 of 11:

Preventing Future Clogs

Download Article

- If your toilet gets clogged often, try to figure out what clogged the toilet and prevent it from happening again. Common culprits are too much toilet paper, tampons (some are flushable but most are not), toys (both kids and pets are suspects), cotton swabs, and baby wipes. Consider having a little "what not to flush" presentation in the best interest of your plumbing.
- Regularly clean the siphon jets around the toilet bowl's edge so that the toilet can flush at full power, making it less likely to clog.
- If your clog was from a child’s toy, invest in some toilet seat locks.

Section 11 of 11:

When to Call a Plumber

Download Article

- Before a clog: If you see (or hear) water backing up in the sinks or showers whenever you flush, that means there's a deep clog that will eventually stop your toilet from working properly. Call a plumber.
- If you smell gas coming from the toilet, it's best to get the plumber and your local electric/ gas company on the scene right away. It could be a cross-bore in the sewers.

Join the Discussion...

I can't call a plumber but my toilet won't unclog. What can I do?

39

WikiSealChaser638

I’m in a rough spot. I have a seriously clogged toilet and I really don’t want my landlord to know. I can't afford a plumber either, so I’m... Read More

WikiMistWhisperer229

Vinegar and baking soda shouldn’t harm the pipes, but that’s also probably not the best option here. Let’s start with the simplest solution... Read More

WikiBandicootJammer750

Dish soap and hot water worked for me! Pour dish soap (or shampoo if you don't have dish soap) down the toilet and then pour hot water down the t... Read More

See all 3 Replies and

Read Discussion

Expert Q&A

Search

Add New Question

Question

What if there is poop in the toilet water?

James Schuelke
Professional Plumber
James Schuelke, along with his twin brother David, is the co-owner of the Twin Home Experts, a licensed plumbing, leak detection, and mold inspection company based in Los Angeles, California. James has over 32 years of home service and business plumbing experience and has expanded the Twin Home Experts to Phoenix, Arizona and the Pacific Northwest.

James Schuelke

Professional Plumber

Expert Answer

It is common to have waste in the water when unclogging a toilet. You can still use a plunger in this case, but you might want to take some additional precautions: (1) Clear the space around the toilet including removing any bath mats/rugs. (2) Use rubber kitchen gloves when plunging. (3) Position yourself in a way to avoid waste water splashing up at you. (4) Have paper towels and cleaning supplies on hand as plunging can create splashback. (5) Have a bucket with soap ready to clean your plunger after use.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 20 Helpful 42

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Read Video Transcript

Tips

If your toilet doesn't flush properly after one flush, don’t flush again or you’ll have an overflowing toliet. Instead, take the lid off of the toilet tank and close the toilet flapper. Closing the flapper (circular drain stopper) will keep more water from entering the bowl.

Thanks
Helpful 16 Not Helpful 9
If the cause of the blockage is an accumulation of feces, clean and disinfect the toilet with plenty of bleach and Creolin (without mixing) to kill parasites and pathogenic bacteria.

Thanks
Helpful 11 Not Helpful 9
If you can see the cause of the clog, reach in and remove it from the toilet if possible. If you can't clear it with your hands, but you know there's an object (such as a child's toy) causing the clog, skip the plunging and go straight to another method.

Thanks
Helpful 9 Not Helpful 14

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Most drain cleaners available in retail stores for home use are not appropriate for toilets. Check the product label to ensure the product is compatible for use with toilet drains. Bear in mind that some drain cleaners produce a great amount of heat as a chemical reaction in contact with water; this heat if not handled properly might seriously damage the toilet and the plastic pipe attached to it.

Thanks
Helpful 28 Not Helpful 12
Coat hangers and drain snakes can scratch the porcelain of the toilet. Try to be careful to minimize the damage, at least in the visible part of the bowl. The end of the coat hanger you are going to introduce in the toilet to "fish" the clog, should be given a v-shaped hook by using some appropriate pliers and then covered lightly with electrical tape. Proceed with greatest caution to engage the hook onto the clog/toy and then softly pull it out in a continuous motion.

Thanks
Helpful 19 Not Helpful 9
Drain-cleaning chemicals are generally extremely toxic and hazardous. One major hazard is the risk of sudden splashback which, depending on the chemical, can cause severe burns. Avoid contact with skin and eyes, and do not mix chemicals. Follow all manufacturer instructions to the letter, and heed all warnings.

Thanks
Helpful 20 Not Helpful 12