How to Adjust Disc Brakes on a Bike

Co-authored by Jonas Jackel

Last Updated: May 20, 2024 Approved

Disc brakes are one of the most common types of brakes found on bicycles. This style of brake has 2 pads that press on either side of the wheel’s rotor (a flat, perforated metal disc) to slow down the bike. Disc brakes come in 2 common varieties: hydraulic and mechanical. If your brakes aren’t working as well as you’d like them to or if they’re rubbing on the rotor when you ride the bike, you can adjust them yourself with an Allen wrench.

Method 1

Method 1 of 3:

Assessing Your Brakes

Download Article

1
Flip your bike upside down or set it in a bike stand. When you adjust your bicycle’s disc brakes, the wheel should be elevated off of the ground so it can spin freely. If you have a bike stand, put your bike in the stand so it’s held in place and elevated off the ground. If you do not have a bike stand, just flip your bike upside down so that the seat and handlebars are on the ground and the wheels are sticking up.^{[1]
X
Research source}
- Portable bike stands are sold at most sporting goods stores. They typically cost between $35–50 USD.
2
Figure out which style of disc brakes you have. Look closely at the caliper at the center of each of your bicycle’s wheels. If the bike’s calipers have a small cable running to them, they are mechanical. If the calipers don’t have any attached cables, they’re hydraulic. If you’re still not sure which style you have, snap a photo of your bike’s brakes and take it to a local cycling shop.^{[2]
X
Research source}
- The caliper looks like a small box about 3 inches (7.6 cm) long that sandwiches the rotor. The caliper is the mechanical device that puts pressure on the rotor and slows down your bicycle.
Advertisement
3
Tighten your wheel in the drop house before adjusting the brakes. A bike’s drop house is the y-shaped frame that the wheel sits between. The drop house attaches to both sides of the wheel and keeps it connected to the bike. Make sure that the wheel is firmly in place by turning the lever on the side of the wheel clockwise. Once you’ve tightened the wheel, fold the lever in until it’s flush with the wheel.^{[3]
X
Research source}
- On some older styles of bike, you may need to tighten the wheel in the drop house manually with an Allen wrench.
4
Avoid touching the edge of the rotor so you don’t cut yourself. The rotor (the circular metal disc that disc brakes apply force to) can be very sharp. As you’re adjusting your disc brakes, try not to touch the edge of the disc. Hold the disc by placing your thumb and fingers on the disc’s 2 flat sides.^{[4]
X
Research source}
- If you do get a cut, stop and wash it with soap. Bandage the small wound before you finish adjusting the brakes.

Method 2

Method 2 of 3:

Adjusting Hydraulic Brakes

Download Article

1
Loosen the 2 bolts on the side of your caliper if the brakes rub. If you can hear your disc brakes rubbing as you drive your bike around, it’s a sign that the brakes are too tight. Inspect the caliper and find both of the ¹⁄₈ inch (0.32 cm) hex bolts that hold the caliper to the frame. Insert an Allen wrench of the corresponding size and twist it a half turn counterclockwise. This should loosen the brakes enough that they stop rubbing.^{[5]
X
Research source}
- It’s possible that the disc brakes are too tight on only 1 wheel. In this case, you will not need to tighten the brake on your other wheel.
2
Squeeze the brake lever 2–3 times to center the caliper on the rotor. After you’ve loosened the 2 hex bolts, squeeze the brake lever that corresponds with the wheel you’re adjusting. If you bumped the caliper while you were loosening it, this will re-center it on the rotor disc. On the last squeeze, keep pressure on the brake lever.^{[6]
X
Research source}
- The right-hand brake lever controls the rear brake and the left-hand brake lever controls the front brake.
3
Tighten the bolts by a half turn before releasing the lever. With the corresponding brake lever held down, again insert the Allen wrench into 1 of the 2 hex bolts. This time, turn the wrench a half turn clockwise to tighten the caliper around the rotor. Tighten the second hex bolts as well.^{[7]
X
Research source}
- If you need to work on both the front and rear brakes at the same time, have a friend hold the brake levers while you work on the calipers.
4
Spin the wheel to make sure that the rubbing has stopped. Make sure that the wheel is unimpeded and can turn freely. Give the wheel a firm spin (in either direction). Listen for the sound of rubbing.^{[8]
X
Research source}
- If the disc brakes no longer rub, you’ve adjusted them successfully!
5
Align the caliper visually over the rotor if the brakes still rub. If the brakes continue to rub, loosen the bolts by a quarter turn. Look down from the top of the caliper and visually align it so that it sits directly over the rotor. With the brake lever held down, fine tune the position of the caliper so that it’s fully centered. Then, tighten the hex bolts a quarter turn.^{[9]
X
Research source}
- Again test the brakes by spinning the wheel and listening for the sound of rubbing brakes.

Method 3

Method 3 of 3:

Tweaking Mechanical Brakes

Download Article

1
Loosen the small set screw found on the side of the caliper. Some models of mechanical disc brakes have a small “set” screw that clamps down on the caliper’s adjustment dial to prevent it from loosening while you’re riding the bike around. Use a small Philips head screwdriver to turn the set screw 1–2 full rotations counterclockwise.^{[10]
X
Research source}
- Not all bikes with mechanical disc brakes have a set screw on the caliper. If yours doesn’t, you can skip this step.
2
Twist the adjustment dial on the side of the caliper to adjust the brakes. Most bikes with mechanical disc brakes have a 1 inch (2.5 cm) wide plastic dial on the side of the caliper (right next to the wheel’s spokes). Turn the wheel clockwise to move the brake pad closer to the rotor and counterclockwise to move it farther away from the rotor.^{[11]
X
Research source}
- In some cases, bikes with mechanical disc brakes may not have an adjustment dial on the side of the caliper. In this case, there will be a hex bolt on the caliper that fills the same function.
3
Adjust the dial until the caliper is centered directly over the metal rotor. It typically takes some fiddling to line the caliper so it’s centered over the rotor. Periodically give the bike’s wheel a spin and visually inspect the brake pad so that you can tell if the pad is rubbing on the disc brake.^{[12]
X
Research source}
- Most rotors aren’t perfectly flat, so don’t worry if you see a small amount of wobble as the rotor spins.
4
Squeeze the brake lever to make sure that the brakes tighten. Give the lever that corresponds to the brake that you’re adjusting a firm squeeze. The 2 pads should tighten on either side of the rotor.^{[13]
X
Expert Source

Jonas Jackel
Owner, Huckleberry Bicycles

Expert Interview. 18 February 2020.} Both of the pads should touch the rotor disc at the same time; if 1 touches before the other, the rotor isn’t properly centered beneath the caliper.^{[14]
X
Research source}
- The right-hand brake lever works the rear brake, and the left-hand brake lever works the front brake.
5
Tighten the hex bolts and the set screw before riding your bike. Use your Allen wrench to turn the 2 hex nuts on the side of the caliper clockwise. Even if you didn’t loosen them when you were adjusting your mechanical disc brakes, check to make sure that the hex bolts are tight. Also use your screwdriver to tighten the small set screw that you loosened earlier.^{[15]
X
Research source}
- Once you’ve tightened the bolts, the bike should be ready to ride!

Expert Q&A

Search

Add New Question

Question

How can I adjust the brakes on my bike?

Jonas Jackel
Bicycle Shop Owner
Jonas Jackel is the Owner of Huckleberry Bicycles, a bicycle retail store based in San Francisco, California. Jonas has over 20 years of experience managing bicycle retail stores and has operated Huckleberry Bicycles since 2011. Huckleberry Bicycles specializes in servicing, repairing, and custom building road, cross, gravel, touring, folding, and e-bikes. Jonas was also previously sat on the Board of Directors for Bike East Bay, a bicycle-advocacy non-profit organization based in Oakland, California.

Jonas Jackel

Bicycle Shop Owner

Expert Answer

Make sure your rotor is right next to the stationary disc, or else the brakes might feel loose.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 3 Helpful 9

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Things You’ll Need

Allen wrench
Philips head screwdriver
Bike stand (optional)

Tips

If you have mechanical disc brakes, you have the option of adjusting them the same way as you adjust hydraulic disc brakes (i.e., by manually loosening the 2 bolts and visually aligning the caliper over the rotor).^{[16]
X
Research source}

Thanks
Helpful 1 Not Helpful 1
If you’re not comfortable adjusting your brakes yourself, you can take your bike to a cycling shop. Be aware, though, that they’ll charge you both an hourly fee for their time and charge you for any parts they decide to replace.

Thanks
Helpful 2 Not Helpful 1