How to Grease Bicycle Wheel Bearings

Author Info

Last Updated: July 25, 2024

The wheel bearings sit between a cone screwed to the wheel axle and the cup in the wheel hub. They must be properly adjusted and greased. To find out if they need greasing without taking everything apart, simply remove the wheel from the bike, support the axle horizontally with your fingers, and turn the wheel slowly--try not to tilt the axle as it rotates. If the wheel does not turn smoothly or you can feel tiny bumps in your fingers, then you must dismantle the bearing assembly and service the bearings.

Steps

Download Article

Make sure they are in sizes 13mm and 15mm. Those are the most common sizes. No other size wrench will work, but any type of adjustable wrench will do for the locking nut.
2
Put the flat wrench on the bearing cone between the hub and the locking nut. Put the adjustable wrench on the locking nut. Hold the bearing cone in place and unscrew the locking nut. The best position to do this is hunched over the wheel while it sits on the ground. Whatever you do, do not open the cones at all while in this position. Just unlock it so you can unscrew everything with your fingers later.^{[1]
X
Research source}
- Some hubs requires thin wrenches for this step, due to limited space between the locking nut and the cassette housing for example.
Advertisement
Now it is time to unscrew the locking nut almost completely off the axle. Next, unscrew the bearing cone to expose the wheel bearings to the light of day. Any grease in there?^{[2]
X
Research source}
The fast way to re-grease your bearings is by just shooting grease in the bearings, screwing the cone back in, flipping the wheel over, hold the cone of the bearing you've just greased, grab the axle now facing up, unscrew it to reveal the other side's bearings and pack them with grease. But the proper way is by taking everything off, clean all the cones, hub cups, bearings, and repack with grease.^{[3]
X
Research source}
Screw the bearing cone back into place, but not too tight. Bearings should be able to roll smoothly without axle play. Tighten the lock nut into place and check again.

Video

Community Q&A

Search

Add New Question

Question

What grease do I use?

Matt Gander

Community Answer

Any kind of thick grease will do the job.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 19 Helpful 17
Question

Should l grease the chain?

Community Answer

If you grease it, it will work more smoothly, but do not add too much of it or you will fall off the bicycle or the chain may fall off due to very less friction.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 82 Helpful 5

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

In order to repack rear wheels, you have to remove the gear cogs on them. In order to do this, you need a special tool to unscrew it. Check with your local bike shop for the proper one. There are a few models and types. It is possible to remove the sprockets without any special tools but it is much more difficult and destructive than using the right tools.

Thanks
Helpful 5 Not Helpful 0
Only undo one side of the axle, this way you are sure that your axle is always centered when you reassemble it.

Thanks
Helpful 6 Not Helpful 1
Make sure the bearing cones are properly torqued down on both sides. The bearings should be loose enough to allow the wheel to spin smoothly and easily, but tight enough so that there is no side-to-side play when the wheel is reinstalled; grasp the fork or frame and push the wheel sideways with your thumb to check.

Thanks
Helpful 6 Not Helpful 2

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Be careful when mixing greases as not all are compatible.

Thanks
Helpful 16 Not Helpful 3
Coaster brake or inner speed hubs are almost bullet proof and very rarely need re-greasing. They're also quite complicated and you should let a professional overhaul those if you aren't confident in your abilities.

Thanks
Helpful 6 Not Helpful 2
If everything is clean, you might have small pits in your bearing cones or cup. The bearings will still work to some extent but it is best to replace them.

Thanks
Helpful 4 Not Helpful 3
If you ever hear crunching noises while turning the axle, dirt has gotten into your bearings and you should start all over again. To avoid this, make sure you work in a clean place.

Thanks
Helpful 4 Not Helpful 4