How to Adjust a Rear Bicycle Derailleur

Co-authored by Jonas Jackel

Last Updated: November 22, 2024 Approved

Have you ever had troubles with your bike switching gears unexpectedly or not shifting correctly? Many people have this problem, but are afraid of attempting to fix it for fear of making things worse. But you don't need to go into the shop to get your bicycle shifting properly. Just adjust the rear derailleur! A good eye and some lubricant should be all you need.

Method 1

Method 1 of 2:

Fixing Shifting Issues

Download Article

You'll need to either lift the bike into a bike stand or flip the bike over so that it rests on the seat and handlebars. To adjust a derailleur, you'll need to pedal the bike while working.
2
Shift the bike to the highest possible gear. On the rear axle, the lowest gear (1^st) is the largest sprocket, and the highest gear (5^th, 6^th, 7^th depending on how many sprockets are on the cassette) is the smallest sprocket. It is furthest away from the centre line of the bike, or closest to the frame fork. A derailleur works by moving the chain from sprocket to sprocket. The derailleur is connected to the shift lever by a steel cable. The derailleur is moved by tightening or relaxing the cable tension. The highest gear (smallest sprocket) on the rear derailleur is actually the point of lowest cable tension, meaning the derailleur is doing the least work and is thus easiest to adjust.
- While pedaling the bike, locate the cable leading to your rear derailleur and pull on it gently. Note how this shifts the chain by moving the derailleur. All a derailleur does is align the chain with the sprockets on the cassette.
Advertisement
The barrel adjuster is the small cylinder connecting the cable to the derailleur. Follow your cable from the rear derailleur up to the handlebars. The tension on this cable is what actually causes gears to shift. You need to have the tension in the cable set up correctly to shift from one gear to the next. Make sure it is seated in its housing and isn't bent, loose, or caught in anything. This isn't a common issue, but it happens.^{[1]
X
Research source}
Keep pedalling the bike, shifting gears one at a time. Make a mental note of points where the chain skips a gear or needs to be clicked twice to shift a gear. Does the derailleur have problems going up or down the gears? Is there any noise or grinding?
5
Return to the highest gear and start shifting until you reach a "problem area," as noted before. For example, if the bike struggles to get from fourth to fifth gear, stop shifting on the fourth gear. While still pedaling, turn the barrel adjuster in the direction you need the cable to fall which, in this case, would be counter-clockwise. Tightening the barrel changes the tension of the cable which, in turn, dictates the gear you're in.^{[2]
X
Research source}
- Note that if the bike is upside-down, you need to turn the barrel away from the direction you want the chain to move. ^{[3]
  X
  Research source}
Loosening the barrel adjuster tightens the cable, making it easier to pull up towards the larger gears. If you shift down and nothing happens, leave it in the shifted gear and keep turning the pedals. Turn the barrel counter-clockwise until the chain jumps up and shifts on its own -- your bike is adjusted.^{[4]
X
Research source}
7
Rotate the barrel adjuster clockwise to help the chain shift up, towards the lower gears. If your chain struggles to move away from the bike, you can tighten the barrel. If it won't shift when you click it, keep pedalling the bike and rotate the barrel. This decreases the tension on the derailleur, allowing the chain to "fall" smoothly to the higher gears. Keep turning slowly until the chain shifts on its own, matching the gear you just tried to shift to.
- Loosening the barrel also helps if your chain is jumping two gears at once when heading to the larger sprockets.^{[5]
  X
  Research source}
8
Check all of the gears by shifting up and down slowly. Once you've adjusted one gear to shift smoothly, the rest of the derailleur usually falls right into place. Check all of the gears to ensure you're adjusted, then move on. If you still have issues:
- Turn the barrel 2-3 turns to the right to full loosen it, then start over. If the cable was too tense when you started, it could need to be re-adjusted from scratch.
- Check for bent gears or derailleur arms. If this didn't work, there is likely a larger issue with the bike.^{[6]
  X
  Research source}
Lubricate the screws and pivot points with bike grease to prevent further issues. Keep the chain lubricated with special chain lube to ensure that stiff chain links do not affect the shifting, and to make sure that the drive train will last a long time.

Method 2

Method 2 of 2:

Fixing Slipping Chains

Download Article

1
Only adjust your limit screws if the chain is popping out on either side of the derailleur. The two screws labeled "L" and "H" are used to adjust your limits. Basically, they determine how far in either direction the chain can travel. Unless you're having issues with the chain falling out, there is no reason to adjust these screws on the rear derailleur (as they were likely set properly at the factory). However, if your bike was in an accident or you installed a new derailleur, these screws may need to be adjusted.
- If you keep slipping a chain, check your limit screws.
- If you can't shift into the highest or lowest gear, check limit screws.
- If your chain is grinding against your frame, check limit screws.^{[7]
  X
  Research source}
Of course, you would turn it counter-clockwise if the chain is getting stopped too early. The high limit is for the smallest gear in the rear derailleur.
Turn the "L" (low) limit screw clockwise to prevent the chain from moving too far to the left (and potentially into your wheel). Again, turn it the opposite way (counter-clockwise) if the limit is pushed too far in. On the rear derailleur, the low limit is for the biggest gear.
Once you've got the limits where you want them, make sure they are lined up nicely. You should see the jockey wheel (metal arm with small cogs under the derailleur) lined up right underneath the chain.^{[8]
X
Research source}
If you are in the furthest gear, you will see the derailleur moving as you adjust the screws. So, if you need to adjust the low limit, shift to the gear on the far left, the biggest one. Adjust both screws a 1/2 turn and notice if the derailleur moves at all. Make sure it lines up in the middle of the gear, then turn back both screws a 1/2 turn so you don't ruin the limits on the correct screw.^{[9]
X
Research source}

Community Q&A

Search

Add New Question

Question

My rear derailleur does not have a barrel adjuster. How do I adjust it without this?

Community Answer

Use the tension adjuster at the gear shifter at the handlebars located under the shift system at the base of the cable housing.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 6 Helpful 20
Question

I have a 7-gear rear derailleur. Recently it started to jump up by 1 gear. For example, if the gear shifter is at 6, it settles into 7 automatically. Moving from 6 to 5 actually moves the gear from 7 to 6. How do I resolve it?

Community Answer

Adjust your barrel adjuster until it drops into the correct gear, which may require adjusting the cable at its anchor point first.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 9 Helpful 22
Question

What if the cog is spinning without engaging the wheel?

Community Answer

If the cog is spinning, it's most likely that the chain itself is out of line. Guide the chain back onto the a gear and hand-pedal it forward gently until it clicks in.

Thanks! We're glad this was helpful.
Thank you for your feedback.
If wikiHow has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission. Support wikiHow
Yes No

Not Helpful 15 Helpful 13

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Adjustments should be made gradually.

Thanks
Helpful 18 Not Helpful 4
Always check to make sure the derailleur hanger (where the derailleur attached to the frame) is not bent, as it must be bent back before attempting to adjust it the derailleur.

Thanks
Helpful 12 Not Helpful 6
The process for adjusting the front derailleur is nearly identical.

Thanks
Helpful 8 Not Helpful 8

Submit a Tip

All tip submissions are carefully reviewed before being published

Name

Please provide your name and last initial

Submit

Thanks for submitting a tip for review!

Warnings

Failure in properly adjusting the rear derailleur can cause the chain to slip off, damaging the frame and possibly sending the derailleur into the rear wheel.

Thanks
Helpful 10 Not Helpful 1
This may be difficult to do if you don't have bicycle repair experience. If you're unsure, go to your nearest favorite bike shop and see if you can get a shop guy to show you how to adjust it.

Thanks
Helpful 8 Not Helpful 6